1. Manuals
  2. Brands
  3. Crary Manuals
  4. Farm Equipment
  5. CWS HONEY BEE AirFLEX AF200 Series
  6. Owner's & parts manual

Crary CWS HONEY BEE AirFLEX AF200 Series Owner's & Parts Manual

Wind system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OW N E R'S/PA R T S
Manual P/N 52624-00
Rev. 092822.01
SN Range: M00001-Current
CRARY WIND SYSTEM
M A N UA L
HONEY BEE
AirFLEX
AF200 SERIES
RECORD SERIAL NUMBER HERE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CWS HONEY BEE AirFLEX AF200 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Crary CWS HONEY BEE AirFLEX AF200 Series

Summary of Contents for Crary CWS HONEY BEE AirFLEX AF200 Series

  • Page 1 CRARY WIND SYSTEM OW N E R’S/PA R T S M A N UA L HONEY BEE AirFLEX AF200 SERIES RECORD SERIAL NUMBER HERE Manual P/N 52624-00 Rev. 092822.01 SN Range: M00001-Current...

  • Page 2: How To Reach Us

    Features may be described herein which are not present in all systems. Crary Industries assumes no obligation of notice to holders of this document with respect to changes subsequently made.

  • Page 3: Limited Warranty

    THE ORIGINAL OWNER OR THE WARRANTY WILL BE VOID. In the event of a failure, return the product, at your cost, along with proof of purchase to the selling Crary Industries dealer. Crary Industries will, at its option, repair or replace any parts found to be defective in material or workmanship. Warranty on any repairs will not extend beyond the product warranty.
  • Page 4 To register your product to be protected under our limited warranty coverage please go to www.crary.com/Product-Support/Product-Registration Please take time to fi ll out the online registration form to register your Crary Wind System and start coverage under our limited warranty.

  • Page 5: Parts Ordering Information

    Only genuine Crary replacement parts should be used to repair the CWS. Crary replacement parts are available from your Crary Dealer. To obtain prompt, effi cient service, remember to give the dealer the correct part description and serial number of the CWS.

  • Page 6: Inspection After Delivery

    GEARBOX MOUNT KIT NUMBER OF NUMBER OF KIT NUMBER KIT NUMBER BOXES IN KIT BOXES IN KIT 52500 52559 REEL ARM MOUNT KIT NUMBER OF KIT NUMBER BOXES IN KIT 52620 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 7: Table Of Contents

    5.5.2 FAN AIR VOLUME ACTUATOR: ........... 27 5.5.3 LIFT/FORE AND AFT ADJUSTMENT: ........27 PROGRAMMING INSTRUCTIONS: ............27 5.6 OPERATING SUGGESTIONS ............28 5.7 TRANSPORTING ................28 5.8 STORAGE ..................29 PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 8 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 9: Introduction

    Diff erences are covered and explained where in fi nding the information you need. Your Crary dealer will appropriate. Use the Table of Contents as a guide to locate be happy to answer any further questions you may have required information.

  • Page 10: Safety

    It may also be used to alert against unsafe practices. IMPORTANT - Instructions that must be followed to ensure proper installation/operation of equipment. NOTE - General statements to assist the reader. Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 11: General Safety

    9. Review safety related items annually with all personnel who will be operating or maintain ing the machine. Think SAFETY! Work SAFELY! PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 12: Operating Safety

    11. First-class maintenance is a prerequisite for the safest operation of your machine. Maintenance, including lubrications, should be performed with the machine stopped and locked out. Think SAFETY! Work SAFELY! Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 13: Hydraulic Safety

    10. Do not clean, lubricate, or adjust the drive shafts when the reel is engaged and the combine is running. THINK SAFETY! WORK SAFELY! PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 14: Transport Safety

    3. When necessary, have someone assist you. 4. Do not allow spectators in the working area. 5. Be sure to read the Maintenance Safety section. Think SAFETY! Work SAFELY! Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 15: Sign-Off Form

    Do not operate or allow anyone else to operate this equipment. equipment until such information has been reviewed. Annually review this information before the season start-up. SIGN - OFF FORM DATE EMPLOYEE SIGNATURE EMPLOYER SIGNATURE PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 16: Safety Decals

    REMEMBER - If safety decals have been damaged, removed or become illegible or parts have been replaced without safety decals, new decals must be applied. New safety decals are available from the manufacturer or an authorized dealer. Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 17 SAFETY PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 18: Assembly

    3.38” SIZE HOLES 30 FT 2, 5 36 FT 3, 6 40 FT 1, 4 45 FT 1, 4 50 FT 1, 4 Figure 1: Fan mount bracket location Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 19: Gearbox/Fan Mount (45')

    Figure 4: Installation (Gauge wheel not shown) CLAMP, GEARBOX MOUNT NUT, 5/8-11 BOLT, 5/8-11 X 8-1/2 GEARBOX MOUNT NUT, 1/2 BOLT, 1/2"-13 X 1-1/4" Figure 3: Gearbox mount bracket location (45’ ) PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 20 8. Place the driveshaft back on the hub shaft. Close the door panel. COGGED SLEAVE T-4 -PLASTIC PLUG SINTERED CARRIAGE BOLT BREATHER SHAFT COLLAR ASSEMBLY Figure 5: Hub Install Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 21: Right Hand Drive Kit

    NE NYLOCK PIN, 3/8 X 1-1/2 WELDMENT, DRIVELINE LYNCH STORAGE BOLT, 1/2 X 1-1/2 BOLT, 3/8 X 1” CARRIAGE HEX HEAD NUT, 1/2” SPIRAL LOCK Figure 7: RH Drive mounts PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 22: Reel Arm Mount

    BOLT, 1/2-13 X X 3-1/2 CRG 3-1/4,FLANGE U-BOLT BOLT, 1/2-13 X 2-3/4, FLANGE MANIFOLD, 40” ALUMINUM WELDMENT, TRANSITION L. SIDE NUT, 5/16-18 NYLOCK-FLANGE Figure 8: LH reel arm installation Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 23: Center Mount

    3/8-16 x 1 MOUNT GUSSETED NUT, 1/2-13 NYLOCK SADDLE FLANGE GUIDE PLATE, RAM CENTER NUT, 3/8-16 ASSEMBLY, NYLOCK NUT, 1/2-13 HALF CLAMP FLANGE NYLOCK FLANGE Figure 10: Center reel arm installation PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 24: Right Hand Mount

    RH RAM INNER ASSEMBLY, TRANSITION R. SIDE NUT, 1/2-13 HALF CLAMP NYLOCK FLANGE NUT, 5/16-18 NYLOCK-FLANGE PLATE, SIDE TRANSITION REAR BOLT, 5/16 X 3-1/2 CRG Figure 12: RH reel arm installation Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 25: Manifold (45 Ft Header)

    HALF CLAMP CONNECTOR 8-11/16" MANIFOLD NUT, 3/8-16 T-BOLT NYLOCK CLAMP 8-11/16" FLANGE T-BOLT HOSE, 8" CLAMP SINGLE HUMP ASSEMBLY, MANIFOLD PIVOT MANIFOLD W/ Figure 16: Center manifold Assembly SERIAL NUMBER PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 26 # OF X-LONG 2 BEND MANIFOLD LENGTH DROP TUBES 30 FT 36 FT 40 FT DRILL HERE 45 FT 50 FT RH Side LH Side Figure 18: Drilling Drop Tube Holes Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 27: Flex Hose Routing

    CLAMP 8-11/16” 156” MANIFOLD T-BOLT U-BOLT CLAMP FLEX HOSE T-BOLT 8-11/16" ELBOW CLAMP 8-3/8" T-BOLT SUPPORT BAND CLAMP 8-11/16" Figure 19: Right Hand - Single Flow fl ex hose installation PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 28 11. Install the flex hose over the elbow support band and the front end of the 40” manifold with an 8-3/8” t-bolt clamp at each end. Figure 22: Tube mount orientation Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 29 5/16-18 X 3/4 SHOULDER GAUGE BOLT INDICATOR INDICATOR BRACKET LINK FLEX HOSE U-BOLT 8-3/8" T-BOLT CLAMP 190" MANIFOLD 8-3/8" T-BOLT CLAMP FLEX HOSE Figure 24: Left hand hose routing PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 30 156" MANIFOLD SCREW, FLEX HOSE 3/8-16 X 1” NUT, 5/16-18 NYLOCK-FLANGE T-BOLT ELBOW ELBOW CLAMP SUPPORT 8-3/8" T-BOLT BAND CLAMP 8-11/16" Figure 25: Left hand hose routing (Dual Flow) Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 31: Electrical Wiring

    Figure 29: Damper position indicator installed (Green/Yellow Wires) SWITCH/MOUNT ASSEMBLY (MOUNT INSIDE COMBINE CAB) (Blue/Orange Wires) FAN BUTTERFLY ACTUATOR (TO 5 AMP HARNESS) WIRELESS REMOTE CONTROL Figure 28: Electrical wiring PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 32: Operation

    By following recommended procedures, a safe working environment is provided for the operator, bystanders and the area around the work site. Untrained operators are not qualifi ed to operate the machine. Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 33: Machine Components

    The CWS stationary air tubes deliver a constant stream high pressure fan. of high velocity air which fi rmly pushes the crop off the Figure 31: Front and Rear views of Machine Components PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 34: Initial Adjustments

    CWS. The torque limiter is set in the CENTER engaged position from the factory. Before use, the slip clutch LOCK NUTS must be slipped and adjusted to ensure proper function. Figure 33: Adjusting the torque limiter Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 35: Pre-Operation Checklist

    Be sure all components are clipped, taped or tied securely in place. 3. Check that all required nuts and bolts are installed and tightened to their specified torque. PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 36: Controls

    1. Locate the push-button labeled "PROGRAM" on the receiver. Press and hold this button until the red LED next to the program button illuminates (approximately 2 seconds). The receiver is now in the transmitter Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 37: Operating Suggestions

    5. Remember: more air uses more horsepower. 6. Gradually adjust air position fore and aft until optimum crop flow is achieved. 7. Gradually reduce air further until minimum air is used to maintain crop flow. PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 38: Removing From Storage

    7. Apply a light coat of grease on the shafts. 8. Check the cutterbar, reel area and drives for entangled material. 9. Touch up all paint nicks and scratches to prevent rust- ing. Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 39: Service & Maintenance

    PTO SHIELD RETAINING BEARING PTO DISCONNECT MECHANISM √ FAN HOUSING AND AIRWAY √ FAN ROTOR YEARLY GEARBOX LUBE CONDITION OF FRICTION DISC √ TORQUE LIMITER (SLIP CLUTCH) √ INSPECT IMPELLER FOR WEAR PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 40: Fluids And Lubricants

    See Figure 37 for the location of oil fi ll and drain plugs. Lubricate the PTO disconnect mechanism. Every 500 operating hours or annually, whichever comes fi rst, the oil should be replaced. When changing the oil, follow this procedure: Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 41: Fan Housing And Air Hose

    KNIFE EDGE AND NEEDS TO BE REPLACED. Figure 40: Critically worn impeller blades 6.7 FAN IMPELLER Every year the fan impeller and airway should be checked for wear or plugging. (Figure 38) PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 42: Torque Limiter (Slip Clutch)

    8. Tighten nuts following an alternating cross pattern until the clutch slips momentarily upon initial startup and then continues to operate normally. Figure 43: Clutch settings Figure 41: Torque limiter (slip clutch) Figure 42: Slip clutch components Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 43: Troubleshooting

    Crary dealer. Before you call, please have this manual and the serial number from your machine ready. BEFORE YOU CALL...

  • Page 44: Specifications

    The table shown below is for reference purposes only and its use by anyone is entirely voluntary, unless otherwise noted. Reliance on its contents for any purpose is at the sole risk of that person. Crary Co. is not responsible for any loss claim or damage arising therefrom.

  • Page 45: Parts Catalog

    Parts Catalog Honey bee AirFLEX Headers AF200 Series PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 46: Gearbox Mount Kit

    NUT, 5/8-11 CENTERLOCK 15232-00 BOLT, 1/2 -13X1-1/4 FLANGE NC 15616 NUT, 1/2 SPIRAL LOCK 52611-12 WELDMENT, MOUNT-CLAMP 55106-12 WELDMENT, MOUNT GEARBOX HBEE AIRFLEX 31716-00 THREADLOCKER, MEDIUM STRENGTH 10ML (NOT SHOWN) Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 47: Drive Kit

    NUT, 3/8-16 NE NYLOCK CMS F1 5ANS 15616 NUT, 1/2 SPIRAL LOCK 17879 PIN, 3/8 X 1-1/2 LYNCH CMS F1 5ANS 32212-00 SHIELD, PTO CONNECTION 52448-12 WELDMENT, STORAGE DRIVELINE (HONEY BEE) 54450-12 PLATE, PTO LOCK PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 48: Gearbox/Fan

    PARTS GEARBOX/FAN SERIES II Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 49 ASSEMBLY, SERIES II GEARBOX/FAN (1/7.250) 54504-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/8.429) 54506-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/8.846) 54505-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/9.385) 17755 LUBRICANT, ANTI-SEIZE (NOT SHOWN) 0.002 PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 50: Gearbox Replacement Parts

    54932 32254-00 GEAR BOX, 7.250:1 54928 3 2255-00 GEAR BOX, 8.429:1 54929 32257-00 GEAR BOX, 8.846:1 54931 32256-00 GEAR BOX, 9.385:1 54930 Kit Includes Service Manual Threadlocker & Box Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 51 BOLT, 3/8NC X 5-1/2 HEX GR8 ZINC COATED 15042 NUT, 3/8 HEX NC 30738-00 BUSHING, DOWEL 3/8 X 1 OIL, MOBIL DELVAC 75W-90 SYNTHETIC (NOT SHOWN) 28 OZ. NPN = No Part Number PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 52: Driveline/C Flange Assembly

    PARTS DRIVELINE/C FLANGE ASSEMBLY ALL MODELS 21 SPLINE SHOWN Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 53 PROFILE, INNER 1B (LONG) 14733-00 PROFILE, OUTER 2A (LONG) 14734-00 TUBE, INNER SHIELD (LONG) 14735-00 TUBE, OUTER SHIELD (LONG) 15575 PIN, M10 X 80 SPRING 12210 DECAL, OUT 12211 DECAL, IN PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 54: Fan Hose Assembly

    MANIFOLD ELBOW - 8” X 90 DEG (MR) 21512 BAND, ELBOW SUPPORT 50508-33 MANIFOLD, 156” ALUMINUM 52679-12 WELDMENT, TRANSITION LT. REAR 76280-00 HOSE, FLEXIBLE 8” ID X 4 FT LONG Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 55 WELDMENT, DUAL FLOW LINK 52013-12 BAR, GAUGE DUAL FLOW INDICATOR 52015-35 BRACKET, INDICATOR DUAL FLOW 52663-12 WELDMENT, MANIFOLD ADJ. REAR 76280-00 HOSE, FLEXIBLE 8” ID X 4 FT LONG PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 56: Right Hand Side

    MANIFOLD, 94” ALUMINUM 50660-00 ASSEMBLY, DUAL FLOW Y 55111-12 WELDMENT, MOUNT TRANSITION - REAR R1 55112-12 WELDMENT, MOUNT TRANSITION - REAR R2 76280-00 HOSE, FLEXIBLE 8” ID X 4 FT LONG Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 57: Hub Assembly

    BREATHER, SINTERED BRONZE, 1/4” NPT 35384-00 HUB, HBEE AF, DRIVE 35385-00 RETAINING RING 80 MM GRV 35386-00 PLUG, T-4 PLASTIC 52450-00 SHAFT, 44MM/ 1-3/8" 6 SPL X 6 SPL STUB PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 58: Damper Indicator Kit

    SCREW, HEX SOC #10-24 X 1.00 ZP 15908-00 BOLT, 5/16-18 X 3/4 ZP FLANGE SHOULDER 52012-12 WELDMENT, DUAL FLOW LINK 52013-12 BAR, GAUGE DUAL FLOW INDICATOR 52015-35 BRACKET, INDICATOR DUAL FLOW Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 59: Reel Arm Mount, Lh

    52621-12 BRACKET, LH RAM OUTER 52622-12 BRACKET, LH RAM INNER 52656-12 PLATE, SIDE TRANSITION REAR PLATE (HONEY BEE) 52681-12 WELDMENT, TRANSITION L. SIDE (HONEY BEE) 54343-12 WELDMENT, REEL MOUNT PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 60: Reel Arm Mount, Center

    GUIDE, SADDLE 52616-12 WELDMENT, ARM MOUNT, GUSSETED 52623-12 PLATE, RAM CENTER 54365-12 WELDMENT, CENTER REEL MOUNT 54370-00 ASSEMBLY, MANIFOLD PIVOT 54382-33 WELDMENT, CWS CONNECTOR MANIFOLD 54886-12 WELDMENT, MANIFOLD PIVOT ROD Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 61: Reel Arm Mount, Rh

    PLATE, SIDE TRANSITION REAR PLATE (HONEY BEE) 52657-12 WELDMENT, TRANSITION R. SIDE (HONEY BEE) 52467-12 WELDMENT, REEL MOUNT W/INDICATOR 52614-12 BRACKET, SMV HONEY BEE 17843 ACTUATOR, ELECTRIC (XXXXX ONLY) PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 62 WELDMENT, 30 FT. (XL) CWS CENTER MANIFOLD (12”) 14077-00 DECAL, CWS LOGO (YELLOW) 15388 NUT, 3/8” NE NYLOCK ZP 15007 BOLT, 3/8” X 1-1/2 GR5 HCS ZP 27214-00 PLATE, CONNECTOR/BAFFLE Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 63 ASSEMBLY, 40FT. CWS MANIFOLD - LH (WITH DECAL) 52683-00 ASSEMBLY, 35FT. CWS MANIFOLD - RH (WITH DECAL) 54380-00 ASSEMBLY, 40FT. CWS MANIFOLD - RH (WITH DECAL) 14077-00 DECAL, CWS LOGO (YELLOW) PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 64 ASSEMBLY, 45FT CWS MANIFOLD - RH (WITH DECAL) 52752-00 ASSEMBLY, 50FT CWS MANIFOLD - RH (WITH DECAL) 50197-00 ASSEMBLY, 45FT CWS MANIFOLD - LH (WITH DECAL) 52751-00 ASSEMBLY, 50FT CWS MANIFOLD - LH (WITH DECAL) Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 65: Drop Tube Kit

    KIT, X-LONG DROP TUBE 2 BEND (INCLUDES ITEMS BELOW) D=47” 15351 NUT, 5/16” SERRATED FLANGE NC ZP 15700-00 U-BOLT, 5/16-18 X 8.19” X 6.59” 17313 FOAM SEAL-AIR TUBE 52557-00 ASSEMBLY, X-LONG AIR TUBE 2 BEND PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...

  • Page 66: Switch/Mount Plate

    LANYARD, CRARY (BLACK) (NOT SHOWN) 33184-00 HARNESS, ACTUATOR - MANIFOLD 31133-00 HARNESS, ACTUATOR - BUTTERFLY 30349-00 SWITCH AND REMOTE, CWS/FAR ACTUATOR CONTROL ASSM 55181-00 KIT, REMOTE, CWS/FAR ACTUATOR CONTROLLER (INCLUDED IN ITEM 4) Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...

  • Page 67: Kit, Drop Tube Feederhouse Cleaner

    NUT, 5/16 NYLOCK 15700-00 U-BOLT, 5/16-18 X 8.19 X 6.59 17313 SEAL, FOAM 31756-00 BOX, 14 X 14 X 6 (NOT SHOWN) 50381-00 BRACKET, FEEDERHOUSE CLEANER 50385-00 TUBE, FEEDERHOUSE CLEANER PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 68 PARTS Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts PN 52624-00...
  • Page 69 PARTS PN 52624-00 Honey Bee AirFLEX AF200 Series Crary Wind System Owner’s/Parts...
  • Page 72 237 12TH ST. NW • P.O. BOX 849 WEST FARGO, ND 58078-0849 Manufactured in the PH: 1-800-247-7335 • FAX: (701) 282-9522 United States of America www.crary.com by Crary Industries...

This manual is also suitable for:

Cws honey bee airflex af240

Table of Contents