Crary CWS CASE IH 2162 Owner's Manual And Parts Manual
  1. Manuals
  2. Brands
  3. Crary Manuals
  4. Farm Equipment
  5. CWS CASE IH 2162
  6. Owner's manual and parts manual

Crary CWS CASE IH 2162 Owner's Manual And Parts Manual

Wind system
Hide thumbs
Table of Contents

Advertisement

Quick Links

OW N E R'S/PA R T S
Manual P/N 50887-00
Rev. 110118.07
SN Range: G00001-Current
CRARY WIND SYSTEM
M A N UA L
CASE IH
2162
MACDON
FD1
FD70
FD75
RECORD SERIAL NUMBER HERE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CWS CASE IH 2162 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Crary CWS CASE IH 2162

Summary of Contents for Crary CWS CASE IH 2162

  • Page 1 CRARY WIND SYSTEM OW N E R’S/PA R T S M A N UA L CASE IH 2162 MACDON FD70 FD75 RECORD SERIAL NUMBER HERE Manual P/N 50887-00 Rev. 110118.07 SN Range: G00001-Current...
  • Page 2 Safety considerations shall be an integral and high prior- ity part of all engineering/design analysis and judgments involving Crary products. It is our stated policy that our products will be manufactured to comply with the safety standards specified by the American Society of Agricultural Engineers, the National Electrical Code, the Society of Automotive Engineers, and/or any other applicable recognized standards at the time manufactured.
  • Page 3 DAYS OF DELIVERY OF THE PRODUCT TO THE ORIGINAL OWNER OR THE WARRANTY WILL BE VOID. In the event of a failure, return the product, at your cost, along with proof of purchase to the selling Crary Industries dealer. Crary Industries will, at its option, repair or replace any parts found to be defective in material or workmanship. Warranty on any repairs will not extend beyond the product warranty.
  • Page 4 To register your product to be protected under our limited warranty coverage please go to www.crary.com/Product-Support/Product-Registration Please take time to fi ll out the online registration form to register your Crary Wind System and start coverage under our limited warranty.
  • Page 5 Only genuine Crary replacement parts should be used to repair the CWS. Crary replacement parts are available from your Crary Dealer. To obtain prompt, effi cient service, remember to give the dealer the correct part description and serial number of the CWS.
  • Page 6 KIT NUMBER BOXES IN KIT NUMBER OF KIT NUMBER 25919 BOXES IN KIT 25920 50203 LEFT HAND DRIVE KIT NUMBER OF KIT NUMBER BOXES IN KIT 50225 50407 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 7: Table Of Contents

    OPTIONS ............79 5.1 MACHINE COMPONENTS .............. 38 5.2 INITIAL ADJUSTMENTS ..............39 DROP TUBE FEEDERHOUSE CLEANER ..........80 DRAPER BRUSH KIT ................81 FEEDERHOUSE TUBE MOUNT KIT ............82 PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 8 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 9: Introduction

    Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your Crary dealer or distributor if you need assistance, information, or additional copies of the manuals.

  • Page 10: Safety

    It may also be used to alert against unsafe practices. IMPORTANT- Instructions that must be followed to ensure proper installation/operation of equipment. NOTE - General statements to assist the reader. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 11: General Safety

    9. Review safety related items annually with all personnel who will be operating or maintain ing the machine. Think SAFETY! Work SAFELY! PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 12: Operating Safety

    11. First-class maintenance is a prerequisite for the safest operation of your machine. Maintenance, including lubrications, should be performed with the machine stopped and locked out. Think SAFETY! Work SAFELY! Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 13: Hydraulic Safety

    10. Do not clean, lubricate, or adjust the drivelines when the reel is engaged and the combine is running.` Think SAFETY! Work SAFELY! PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 14: Transport Safety

    2. Use only lifts, cranes and tools with sufficient capacity for the load. 3. When necessary, have someone assist you. 4. Do not allow spectators in the working area. Think SAFETY! Work SAFELY! Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 15: Sign-Off Form

    Do not operate or allow anyone else to operate this equip- ment. ment until such information has been reviewed. Annually review this information before the season start-up. SIGN - OFF FORM DATE EMPLOYEE SIGNATURE EMPLOYER SIGNATURE PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 16: Safety Decals

    REMEMBER - If safety decals have been damaged, removed or become illegible or parts have been replaced without safety decals, new decals must be applied. New safety decals are available from the manufacturer or an authorized dealer. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 17 PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 18: Assembly

    Use Mobilube SHC 75W-90 synthetic gear lube or equivalent with the following specifications: API Service GL-5/MT.1 MIL-L-2105D MACK GO-J PLUS SAE J2360 Capacity: 28 ounces (0.8 liters) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 19 LOCK NUT, 3/8"-16 NYLOCK- FLANGE OUTER MOUNT INNER MOUNT SUPPORT SUPPORT BOLT, 3/8"-16 x 1-1/4 BOLT, 1/2" x 1-1/4" CARRIAGE SERRATED FLANGE Figure 3: Right hand gearbox/fan mount PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 20: Gearbox/Fan Mount (Fd70 , Fd75 & Cih 2162 Headers)

    SAE J2360 Capacity: 28 ounces (0.8 liters) ATTENTION For Hillco applications, please refer to the supplemental installation manual supplied with your drive line. Figure 6: Support bracket Series II Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 21 NUT, 3/8 NUT, 3/8 BOLT, 1/2 X 1-1/4 NYLOCK-FLANGE NYLOCK-FLANGE 1/2 X 1-1/4 BRACKET, BRACKET, NUT, 3/8 LOWER SUPPORT UPPER SUPPORT NYLOCK-FLANGE Figure 8: Right hand gearbox/fan mount PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 22: Right Hand Drive Kit

    5/16” U-bolts and four nuts (Figure 42). REAR TUBE MOUNT SCREW, 11/32 X 7/8 SERIES II GEARBOX KIT BOLT, 3/8 X 3/4 PTO SHIELD SERR FLANGE Figure 10: Right hand drive kit assembly Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 23: Driveline Adjustment

    6. File both shaft ends, and slide the two halves back together. Figure 12: Removing the shield tube PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 24: Reel Arm Mount (Fd1 & Fd75 Headers)

    7. Install new cylinder mount using four 1/2” x 1” Torx bolts. The top hole will not be used on the LH side. Figure 14: LH reel mount (FD1 & FD75 headers) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 25 5/8 FLAT 5/8 X 3-1/4 BOLT, BOLT, 1/2 X 1 TORX 1/2 X 5-1/2 WASHER, 1/2 FLAT Figure 15: Left reel arm mount assembly (FD1 & FD75 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 26: Center Mount

    7. Install new cylinder mount using four 1/2” x 1” Torx bolts. 8. Attach the cylinder to the cylinder mount with the provided cylinder pin and two hair pins. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 27 BRACKET BOLT, 1/2 X 4-1/2 BOLT, 1/2 X 1-1/4 BOLT, 1/2 X 1 TORX NUT, 1/2 NYLOCK Figure 17: Center reel arm mount assembly (FD1 & FD75 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 28: Right Hand Mount

    Figure 19: RH reel mount (FD75 headers) RE-USE OEM HARDWARE TO MOUNT THE TRANSPORT LIGHT IN THESE TWO FRONT Ø.53 HOLES Figure 20: Transport light Figure 21: Cylinder mount Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 29 NUT, 3/8 NYLOCK RH REEL MOUNT WASHER, 1/2 FLAT NUT, 1/2 NYLOCK BOLT, 1/2 X 1 TORX Figure 22: Right reel arm mount assembly (FD1 & FD75 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 30: Reel Arm Mount (Fd70 & Cih 2162 Headers)

    OEM hardware removed in step 2. 12. Reconnect cylinder reusing the OEM hardware (Figure 26). Figure 25: Bearing assembly (FD70 & CIH 2162 headers) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 31 SHOULDER BORE ADAPTER CWS TUBE MOUNT SPACER, RADIAL .63 X .63 BEARING WASHER, 3/8 SAE FLAT Figure 26: LH reel arm mount assembly (FD70 & CIH 2162 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 32: Center Mount

    OEM hardware removed in step 2. 10. Reconnect cylinder using provided cylinder pin and two hair pins (Figure 27). 11. Ensure the RH, LH and center reel mount assemblies are at equal height. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 33 NYLOCK FLANGE SPACER SHOULDER BORE ADAPTER SPACER, RADIAL .63 X .63 BEARING WASHER, 3/8 SAE FLAT Figure 29: Center reel arm mount assembly (FD70 & CIH 2162 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 34: Right Hand Mount

    OEM hardware removed in step 2 as shown (Figure 32). 12. Reconnect cylinder reusing the OEM hardware (Figure 32). Figure 32: Cylinder Mount (FD70 & CIH 2162 headers) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 35 SHOULDER BORE ADAPTER CWS TUBE SPACER, MOUNT RADIAL .63 X .63 BEARING WASHER, 3/8 SAE FLAT Figure 33: RH reel arm mount assembly (FD70 & CIH 2162 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 36: Manifold

    14. On single flow headers only, install end cap using 8-3/8” T-bolt clamp on LH of manifold (Figure 35). Figure 36: Electric actuator Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 37 CENTER REEL MOUNT NUT, 3/8 NYLOCK HALF CLAMP BOLT, 3/8 X 1 CRG CONNECTOR MANIFOLD SINGLE HUMP HOSE CLAMP, 8-11/16" T-BOLT Figure 37: Center manifold Assembly (FD1 & FD75 headers) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 38: Drop Tube Assembly

    RH side of the header so that there is 3.25” between them and the end reel tines to allow clearance for the end drop tubes. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 39: Flex Hose Routing

    After determining movement of the reel. the length of hose needed, cut the hose. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 40 FLEX HOSE CLAMP 8-3/8" T-BOLT CLAMP ELBOW SUPPORT BAND 45 ELBOW Figure 42: Right Hand - Single fl ow air hose installation (30’ FD70 & CIH 2162 headers) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 41 Leave enough slack in this portion of flex hose to allow complete up/down and fore/aft movement of the reel. 21. Install the flex hose over the elbow support band and PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 42 11/32 X 7/8 FD1/FD75 REAR-CENTER TUBE MOUNT BRACKET U-BOLT 141" MANIFOLD REAR TUBE REAR-CENTER TUBE MOUNT MOUNT BRACKET FLEX HOSE LEFT REAR MANIFOLD Figure 45: Left hand tube clamp locations Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 43 U-BOLT T-BOLT CLAMP 8-3/8" TUBE T-BOLT MOUNT CLAMP8-11/16" MANIFOLD T-BOLT CLAMP FLEX HOSE 8-3/8" T-BOLT CLAMP ELBOW ELBOW 8-3/8" SUPPORT Figure 47: Left hand hose routing (Dual Flow) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 44: Electrical Wiring

    MANIFOLD TILT ACTUATOR (TO 15 AMP HARNESS) SWITCH/MOUNT ASSEMBLY (MOUNT INSIDE COMBINE CAB) FAN BUTTERFLY ACTUATOR (TO 5 AMP HARNESS) WIRELESS REMOTE CONTROL Figure 49: Electric wiring Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 45: Operation

    By following recommended procedures, a safe working environment is provided for the operator, bystand- ers and the area around the work site. Untrained operators are not qualifi ed to operate the machine. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 46: Machine Components

    Proper proper setup and operation of your Crary Wind System. Front of Head Rear of Head Figure 50: Machine components Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 47: Initial Adjustments

    2-3 seconds to make the torque limiter slip. Do not allow the torque limiter to slip for more than 2-3 Figure 51: Adjusting the torque limiter seconds at a time to prevent damage to the linings. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 48: Pre-Operation Checklist

    Be sure all components are clipped, taped or tied securely in place. 3. Check that all required nuts and bolts are installed and tightened to their specified torque. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 49: Controls

    (FULLY CLOSED POSITION) Figure 53: Air fl ow REEL LIFT/FORE AND AFT ADJUSTMENT: Consult your owner/operator’s manual that came with your Figure 54: Fan butterfl y actuator header. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 50: Operating Hints

    Add extra lights when transporting at night or during periods of limited visibility. 3. See the owner’s manual that came with your combine and header for proper transportation guidelines. Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 51: Storage

    7. Apply a light coat of grease on the shafts. 8. Check the cutterbar, reel area and drives for entangled material. 9. Touch up all paint nicks and scratches to prevent rust- ing. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 52: Service & Maintenance

    PTO DISCONNECT MECHANISM √ FAN HOUSING AND AIRWAY √ FAN ROTOR YEARLY GEARBOX LUBE CONDITION OF FRICTION DISC √ TORQUE LIMITER (SLIP CLUTCH) √ INSPECT IMPELLER FOR WEAR Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 53: Fluids And Lubricants

    fi rst, the oil should be replaced. When changing the oil, follow this procedure: 1. Place a container under the gearbox. 2. Remove the drain plug. Allow 10 minutes to drain. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 54: Pto Lubrication

    Figure 59: Friction disc torque limiter (slip clutch) Figure 57: Checking fan housing and air hose Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 55: Troubleshooting

    If you encounter a problem that is diffi cult to solve, even after having read through this trouble shooting section, please call your local Crary dealer. Before you call, please have this manual and the serial number from your machine ready.

  • Page 56: Specifications

    The table shown below is for reference purposes only and its use by anyone is entirely voluntary, unless otherwise noted. Reliance on its contents for any purpose is at the sole risk of that person. Crary Co. is not responsible for any loss claim or damage arising therefrom.

  • Page 57: Parts Catalog

    PARTS PARTS CATALOG MacDon/CIH Headers FD70/CIH 2162 FD75 PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 58 PARTS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 59: Gearbox Mount Kit

    BRACKET, MOUNT SUPPORT - INNER 51641-12 WELDMENT, SERIES II GEARBOX MOUNT 51646-12 PLATE, SPACER 51647-12 PLATE, REINFORCEMENT 51648-12 BRACKET, PTO HOLDER 51649-12 BRACKET, ADJUSTMENT 31716-00 THREADLOCKER, MEDIUM STRENGTH, 10ML (NOT SHOWN) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 60 BRACKET, LOWER SUPPORT 53669-12 BRACKET, MOUNT SUPPORT 53670-12 PLATE, GEARBOX MOUNT 53683-12 BRACKET, PTO HOLDER 54562-12 WELDMENT, SERIES 2 GEARBOX MOUNT 31716-00 THREADLOCKER, MEDIUM STRENGTH, 10ML (NOT SHOWN) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 61 PLATE, GEARBOX MOUNT 53683-12 BRACKET, PTO HOLDER 54761-12 WELDMENT, SERIES 2 GEARBOX MOUNT 54871-12 BRACKET,HIGH MOUNT SUPPORT,UPPER 54872-12 BRACKET,HIGH MOUNT SUPPORT,LOWER 31716-00 THREADLOCKER, MEDIUM STRENGTH, 10ML (NOT SHOWN) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 62: Gearbox/Fan

    PARTS GEARBOX/FAN ALL MODELS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 63 ASSEMBLY, SERIES II GEARBOX/FAN (1/7.250) 54504-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/8.429) 54506-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/8.846) 54505-00 ASSEMBLY, SERIES II GEARBOX/FAN (1/9.385) 17755 LUBRICANT, ANTI-SEIZE (NOT SHOWN) 0.002 PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 64: Gearbox Replacement Parts

    PARTS GEARBOX REPLACEMENT PARTS SERIES II Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 65 BUSHING, DOWEL 3/8 X 1 NAMEPLATE TAG, LUBRICATION PLUG, PIPE SOCKET 1/8NPT 7/8 TAPER OIL, MOBIL DELVAC 75W-90 SYNTHETIC (NOT SHOWN) 28 OZ. GREASE, MOBILTH SHC 007 (NOT SHOWN) 0.5 OZ. PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 66: Driveline/C Flange Assembly

    PARTS DRIVELINE/C FLANGE ASSEMBLY ALL MODELS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 67 PROFILE, INNER 1B (LONG) 14733-00 PROFILE, OUTER 2A (LONG) 14734-00 TUBE, INNER SHIELD (LONG) 14735-00 TUBE, OUTER SHIELD (LONG) 15575 PIN, M10 X 80 SPRING 12210 DECAL, OUT 12211 DECAL, IN PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 68: Fan Hose Assembly

    50139-12 WELDMENT, TUBE MOUNT 15176 SCREW, 11/32 X 7/8 HWH AB THREAD 15617 BOLT, 3/8 X 3/4 SERR FLANGE 32212-00 SHIELD, PTO CONNECTION 50682-12 MOUNT, MACDON TRANSITION MANIFOLD Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 69 MANIFOLD, 111" ALUMINUM 54857-00 MANIFOLD, 120” ALUMINUM 52011-00 KIT, DUAL FLOW DAMPER INDICATOR 17777 FLEX HOSE, 8”ID X 8FT. (NOT SHOWN) 76280-00 HOSE, 8" X 4' FLEXIBLE (NOT SHOWN) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 70: Reel Arm Mount (Lh)

    PARTS REEL ARM MOUNT - LH FD1 & FD75 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 71 WELDMENT, REEL MOUNT - LH 51417-00 ASSEMBLY, REEL ARM MOUNT (INCLUDES ITEMS 14 AND 18) CAP, END ITEM PART NUMBER DESCRIPTION 16091 CLAMP, T-BOLT (8-1/4”) 21924 CAP, TUBE 8” (NOTCHED) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 72: Reel Arm Mount - Center

    PARTS REEL ARM MOUNT - CENTER FD1 & FD75 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 73 WELDMENT, CENTER REEL MOUNT 54370-00 ASSEMBLY, MANIFOLD PIVOT 54382-33 WELDMENT, CWS CONNECTOR MANIFOLD 54831-12 WELDMENT, REEL MOUNT-CENTER 54835-12 BRACKET, REEL ARM MOUNT-CENTER 54840-12 WELDMENT, CYLINDER MOUNT-CENTER 54843-12 PIN, CYLINDER MOUNT PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 74: Reel Arm Mount - Rh

    PARTS REEL ARM MOUNT - RH FD1 & FD75 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 75 54853-12 WELDMENT, CYLINDER MOUNT-OUTER 54862-12 BRACKET, REEL ARM MOUNT - RH 50139-12 WELDMENT, TUBE MOUNT 22809 SADDLE GUIDE 51417-00 ASSEMBLY, REEL ARM MOUNT (INCLUDES ITEMS 19 AND 26) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 76 PARTS REEL ARM MOUNT (LH) FD70 & CIH 2162 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 77 53666-12 WELDMENT, CYLINDER MOUNT 70046 IDLER SPACER 70362 SPACER .63 X .63 PULLEY CAP, END ITEM PART NUMBER DESCRIPTION 16091 CLAMP, T-BOLT (8-1/4”) 21924 CAP, TUBE 8” (NOTCHED) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 78 PARTS REEL ARM MOUNT (CENTER) FD70 & CIH 2162 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 79 ASSEMBLY, MANIFOLD PIVOT 54382-33 WELDMENT, CWS CONNECTOR MANIFOLD 54682-12 TUBE, ARM MOUNT 54684-00 PIN, CYLINDER MOUNT 54886-12 WELDMENT, MANIFOLD PIVOT ROD 70046 IDLER SPACER 70362 SPACER .63 X .63 PULLEY PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...
  • Page 80 PARTS REEL ARM MOUNT (RH) FD70 & CIH 2162 HEADERS Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 81 50139-12 WELDMENT, TUBE MOUNT 53662-12 STRAP, ADJUSTMENT 53666-12 WELDMENT, CYLINDER MOUNT 70046 IDLER SPACER 70362 SPACER .63 X .63 PULLEY 17410 FLEX HOSE, 8"ID X 6FT. (NOT SHOWN) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 82: Air Manifold

    ASSEMBLY, 30FT. CWS MANIFOLD - RH (WITH DECAL) 54868-00 ASSEMBLY, 35FT. CWS MANIFOLD - RH (WITH DECAL) 54380-00 ASSEMBLY, 40FT. CWS MANIFOLD - RH (WITH DECAL) 14077-00 DECAL, CWS LOGO (YELLOW) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 83 BOLT, 3/8 X 1-1/2 HEX GR5 ZP 15388 NUT, 3/8 NE NYLOCK ZP 50198 ASSEMBLY, 45FT CWS MANIFOLD - RH (WITH DECAL) 50197 ASSEMBLY, 45FT CWS MANIFOLD - LH (WITH DECAL) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 84: Drop Tube Kit

    KIT, SHORT DROP TUBE (INCLUDES ITEMS BELOW) D=36” 15351 NUT, 5/16” SERRATED FLANGE NC ZP 15700-00 U-BOLT, 5/16-18 X 8.19” X 6.59” 25831-00 ASSEMBLY, SHORT AIR TUBE 17313 FOAM SEAL-AIR TUBE (NOT SHOWN) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 85: Damper Indicator Kit

    SCREW, HEX SOC #10-24 X 1.00 ZP 15908-00 BOLT, 5/16-18 X 3/4 ZP FLANGE SHOULDER 52012-12 WELDMENT, DUAL FLOW LINK 52013-12 BAR, GAUGE DUAL FLOW INDICATOR 52015-35 BRACKET, INDICATOR DUAL FLOW PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 86: Switch/Mount Plate

    LANYARD, CRARY (BLACK) (NOT SHOWN) 33184-00 HARNESS, ACTUATOR - MANIFOLD 31133-00 HARNESS, ACTUATOR - BUTTERFLY 30349-00 SWITCH AND REMOTE, CWS/FAR ACTUATOR CONTROL ASSM 50892-00 WIRELESS REMOTE CONTROL (INCLUDED IN ITEM 4) Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 87: Options

    PARTS Parts Catalog Crary Wind System OPTIONS PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 88: Drop Tube Feederhouse Cleaner

    NUT, 5/16 HEX NC ZP 15356 NUT, 5/16 NE NYLOCK ZP 15700-00 U-BOLT, 5/16-18 X 8.19 X 6.59 17313 FOAM SEAL - AIR TUBE 50381-00 BRACKET, FEEDERHOUSE CLEANER 50382-00 TUBE, FEEDERHOUSE CLEANER Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...

  • Page 89: Draper Brush Kit

    BOLT, 1/4-20 X 3/4 HWH GR5 CZP 15177-00 RIVET, 1/4-20 OE KNRLD NUT 50398-00 ASSEMBLY, 38" BRACKET/BRUSH FD70/75 50399-00 ASSEMBLY, 72" BRACKET/BRUSH FD70/75 TOOL, 1/4-20 MANUAL RIVNUT INSTALL (NOT 30366-00 SHOWN) PN 50887-00 Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts...

  • Page 90: Feederhouse Tube Mount Kit

    DUAL FLOW MACDON FD70 FEEDERHOUSE TUBE MOUNT KIT KIT, FEEDER HOUSE MOUNTS DUAL FLOW MACDON FD70 - (50767) ITEM PART NUMBER DESCRIPTION 50450-00 WELDMENT, MACDON FD70 TUBE MOUNT BRACKET Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts PN 50887-00...
  • Page 92 237 12TH ST. NW • P.O. BOX 849 WEST FARGO, ND 58078-0849 Manufactured in the PH: 1-800-247-7335 • FAX: (701) 282-9522 United States of America www.crary.com by Crary Industries...

This manual is also suitable for:

Cws macdon fd1Cws macdon fd70Cws macdon fd75

Table of Contents

Save PDF