Precor Vitality FTS Glide Assembly And User's Manual

Vitality® Benches and Racks
Vitality FTS Glide | Assembly and Use Guide
Assembly Requirements
Precor recommends at least two (2) people for this installation. DO NOT
attempt assembly by yourself.
When assembling the equipment, we recommend you:
• Follow the assembly instructions in order.
• Unpack the box and assemble the equipment close to where you plan to use it.
• Locate the equipment at least 40 inches (1 meter) away from walls or furniture on
either side of the equipment, and 40 inches (1 meter) away from objects behind or
in front of the equipment.
• Assemble the equipment on a solid, flat surface so it remains level and stable.
• DO NOT move equipment without assistance.
Required Tools
• 6 ft (2 m) step ladder rated Type I
• Open-end and socket wrench set (metric)
• Philips screwdriver
• Metric hex wrench set
• Metric hex bit set
• Torque wrench 75 ft-lb (100 N-m)
Hardware Kit
Name
1 1
Right side frame
2 2
Left side frame
3 3
Upper cross frame (accessory rack)
4 4
Lower cross frame
5 5
Pull-up bar
6 6
Pulley
7 7
Left inner shroud
8 8
Right inner shroud
9 9
Outer shroud
Accessories
Handles (2) Ankle strap
1. Frame assembly
1. With your assistant, stand up the
rear feet approximately 22-inches (54 cm) apart and the front feet approximately
51-inches (130 cm) apart. Connect the
each side with 4 10 10 M10 x 65 mm HHB, 8
nuts (Figure 2). Partially tighten.
2. Connect the lower cross frame to each side with 4
4 4
11 mm washers, and 4 15 15 M10 lock nuts (Figure 2). Partially tighten.
1 1
©2024 Precor Incorporated | Vitality Strength
Qty Name
10 10
1 M10 x 65 mm hex head bolt (HHB)
11 11
M10 x 50 mm hex head bolt (HHB)
1
12 12
M6 x 45 mm button head cap screw (BHCS)
1
13 13
Flat washer, 11 mm
1
14 14
Flat washer, 8 mm
1
15 15
M10 lock nut
2
Weight plate 10 lb (4.5 kg)
1
Weight plate 5 lb (2.3 kg)
1
Weight labels
2
Handlebar
1 1 right and left side frames. Space the
2 2
3 3 upper cross frame (accessory rack) to
13 13 11 mm washers, and 4
10 10
M10 x 65 mm HHB, 8
2 2
13 13
10 10
13 13
3 3
15 15
15 15
4 4
13 13
13 13
10 10
Figure 2.
Left side
frame
Qty
8
2
32
20
32
10
14
10
2
2. Attach pull-up bar
1. Use the ladder and carefully loosen the M10 hex head bolts and nuts connected to
the upper pulleys on both side frames (Figure 3). DO NOT REMOVE AT THIS TIME.
2. Remove the nuts and washers on the inside only (Figure 4). Have your assistant
15 15 M10 lock
pull the hex head bolts on one side slightly outward WITHOUT causing the pulley
to fall. Set the
13 13
pull-up bar frame and replace the washers and nuts (Figure 5).
CAUTION Allowing the pulley to fall may cause injury or damage to the
equipment or part.
3. Repeat for the other side.
4. Square frame and torque ALL M10 hardware to 37 ft-lb (51 N-m).
Vitality FTS Glide | Assembly Guide | P/N 306965-101B| 2024 12 03 | Page 1 of 2
Upper cross frame
Inner
shrouds
Lower cross frame
Figure 1. Vitality FTS Glide
pull-up bar into place. Slide the hex head bolts back through the
5 5
Figure 3.
5 5
Figure 5.
Outer shroud
Pull-up bar
Right side
frame
Figure 4.