Scheppach HC26 Translation Of Original Instruction Manual page 23

10 Pull the plug out of the outlet
- During non-use of the electric tool or prior to
maintenance and when replacing tools.
11 Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
12 Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13 Remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the electric tool
when you are distracted.
14 Check the electric tool for potential damage
- Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any electric tool on which the switch
cannot be switched on and off.
15 Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
16 Important!
- For your own safety you must only use the acces-
sories and additional units listed in the operating
instructions or recommended or specified by the
manufacturer. The use of mounted tools or ac-
cessories other than those recommended in the
operating instructions or catalog may place your
personal safety at risk.
17 Noise
- Wear ear muffs when you use the compressor.
18 Replacing the power cable
- To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualified electrician. There is a risk of
electric shock!
19 Inflating tires
- Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
20 Roadworthy compressors for building site oper-
ations
- Make sure that all lines and fittings are suitable
for the maximum permissible operating pressure
of the compressor.
21 Place of installation
- Set up the compressor on an even surface.
22. Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
23. Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24. Use a residual current circuit breaker with a trigger
current of 30 mA or less. Using a residual current
circuit breaker reduces the risk of an electric shock.
m WARNING! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain con-
ditions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical im-
plants consult with their physician and the manufacturer
of the medical implant prior to operating the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
Observe the corresponding operating manuals of
the respective compressed air tools / compressed
air attachments! The following general warnings
must also be observed.
Safety instructions for working with compressed
air and blasting guns
• Ensure there is sufficient distance to the product, at
least 2.50 m, and keep the compressed air tools /
compressed air attachments away from the com-
pressor during operation.
• The compressor pump and lines can become very hot
during operation. Touching these parts will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand.
www.scheppach.com GB | 23