Page 1
VUTR 651 PE EC L A21 VUTR 351 PE EC R A21 VUTR 651 PE EC R A21 VUER 351 P EC L A21 VUER 651 P EC L A21 VUER 351 P EC R A21 VUER 651 P EC R A21...
SAFETY REQUIREMENTS This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the unit by a person responsible for their safety. Children should be supervised to ensure that they do not play with the unit.
Page 4
Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc. Do not close or block the intake or extract vents in order to ensure the efficient air flow. Do not sit on the unit and do not put objects on it.
PURPOSE The unit is designed to ensure continuous mechanical air exchange in houses, offices, hotels, cafés, conference halls, and other utility and public spaces to recover the heat energy contained in the air extracted from the premises and warm up the filtered stream of supply air, as well as for exhaust ventilation in kitchens, commercial bakeries etc.
VUTR (VUER) 351/651 P(E) EC TECHNICAL DATA The unit is designed for indoor application with the ambient temperature ranging from +1 °C up to +40 °C and relative humidity up to 60 % without condensation. In cold, damp rooms, there is a possibility of freezing or condensation inside and outside the casing. In order to prevent condensation on the internal walls of the unit, it is necessary that the surface temperature of the casing is 2-3 °C above the dew point temperature of the transported air.
VUTR (VUER) 351/651 P(E) EC DESIGN AND OPERATING PRINCIPLE The unit operation is as follows: warm, stale extract air flows through the air ducts into the unit and is filtered. Then the air is moved through the rotary heat exchanger and is exhausted outside through the air ducts with the extract fan. Cold fresh intake air flows through the air ducts into the unit’s supply filter, where it is filtered.
MOUNTING AND SET-UP READ THE USER'S MANUAL BEFORE INSTALLING THE UNIT. THE UNIT MUST BE MOUNTED BY A QUALIFIED EXPERT ONLY, PROPERLY TRAINED AND HAVING THE REQUIRED TOOLS AND MATERIALS. The units are available in left-hand and right-hand design. Choosing the right design can improve the ease of installation, shorten the length of the ducts and reduce the number of air duct bends.
Page 10
VUTR (VUER) 351/651 P(E) EC The air ducts must be slipped over the unit flanges until tight. Flexible air ducts must be rigidly fixed with a metal worm clamp. If the air ducts are too short or not connected, protect the unit parts from ingress of foreign objects. To prevent uncontrollable access to the fan the spigots may be covered with a protecting grille or other protecting device mesh width not more than 12.5 mm.
Page 11
SERVICE PANEL The unit is equipped with a hinged service panel for technical and maintenance operations. The unit design enables the user to remove the service panel. Remove the hinge lock and disconnect the grounding wire to remove the service panel. The VUTR (VUER) 651 P(E) EC is equipped with two hinged service panels for repair and maintenance work.
UNIT DESIGN To ensure comfortable installation and provide space for accessing the unit, left and right design types of the unit are designed. VUTR (VUER) 351/651 P(E) EC R VUTR (VUER) 351/651 P(E) EC L Top view VUTR (VUER) 351/651 P(E) EC L VUTR (VUER) 351/651 P(E) EC R A –...
VUTR (VUER) 351/651 P(E) EC CONNECTION TO POWER MAINS ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED AND WILL VOID THE WARRANTY. The unit is designed for connection to power mains with the parameters specified in the technical data table. The connection must be made using durable, insulated and heat-resistant conductors (cables, wires).
EXTERNAL WIRING DIAGRAM Valve1 Valve2 N PE 9 10 B +24V SM1* SM2* CCU* PK1* Boost* Designation Name Wire Model Note SM1* Supply damper actuator 2 x 0.75 3A, 30VDC/~250VAC SM2* Exhaust damper actuator 2 x 0.75 3A, 30VDC/~250VAC PK1* Contact from fire alarm panel 2 x 0.75 Remove the jumper,~250VAC...
VUTR (VUER) 351/651 P(E) EC TECHNICAL MAINTENANCE DISCONNECT THE UNIT FROM POWER MAINS BEFORE ANY MAINTENANCE OPERATIONS! Maintenance operations of the unit are required 3-4 times per year. They include general cleaning of the unit and the following operations: 1. Filter maintenance. Clogged filters increase air resistance in the system and reduce supply air volume.
Page 17
VUTR (VUER) 651 P(E) EC 3. Fan maintenance (once per year). Even in case of regular maintenance of the filters and the heat exchanger, some dust may accumulate inside the fans and reduce the fan performance and supply air flow. Clean the fans with a soft brush or cloth.
VUTR (VUER) 351/651 P(E) EC TROUBLESHOOTING Possible faults and troubleshooting Problem Possible reasons Troubleshooting Make sure the power supply line is connected No power supply. correctly, otherwise troubleshoot the connection error. The fan(s) does (do) not start when the unit is on. The motor is jammed, the impeller blades are Turn the unit off.
MANUFACTURER’S WARRANTY The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU of the European Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking Council Directive 93/68/EEC.
CERTIFICATE OF ACCEPTANCE Unit Type Single-room air handling unit with heat recovery Model Serial Number Manufacture Date Quality Inspector’s Stamp SELLER INFORMATION Seller Address Phone Number E-mail Purchase Date This is to certify acceptance of the complete unit delivery with the user’s manual. The warranty terms are acknowledged and accepted.
Need help?
Do you have a question about the VUER 351 P EC L A21 and is the answer not in the manual?
Questions and answers