Subscribe to Our Youtube Channel
Related Manuals for Eaton PSPD Series
Summary of Contents for Eaton PSPD Series
- Page 1 ® ® E E a a t t o o n n P P S S P P D D S S e e r r i i e e s s Installation Manual p/n: IM01005032E Revision 04...
- Page 2 Eaton reserves the right to change specifications without prior notice. Eaton is a registered trademark and is a trademark of Eaton or its subsidiaries and affiliates. All other trademarks are property of their respective companies. ©Copyright 2025 Eaton, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the...
- Page 3 9 9 W W a a r r r r a a n n t t y y ............................................................2 2 4 4 Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 4 The Eaton PSPD Series is designed to mount on the wall (or other vertical surface) as close as possible to the electrical cabinet. The SPD Series is available in voltage ratings from 120-600V AC, surge current capacity ratings from 50kA to 400kA, and NEMA 1, NEMA 4 or NEMA 4X enclosures.
- Page 5 C C a a t t a a l l o o g g N N u u m m b b e e r r i i n n g g S S y y s s t t e e m m Each Eaton PSPD Series unit has a name plate that identifies the parameters used for manufacture. These...
- Page 6 Conducting dielectric, Megger, or Hi-potential testing with the PSPD installed will cause internal damage to the PSPD. The PSPD will also cause the test to fail. Every Eaton PSPD Series unit is tested at the factory for dielectric breakdown. No further SPD testing is required for installation.
-
Page 7: Installation
The ideal mounting location for the Eaton PSPD Series is as close as possible to the electrical enclosure. The Eaton PSPD Series should be mounted in such a way as to minimize any sharp bends in the wiring conduit. 2 2 . . 3 3... - Page 8 Figure 9 Figure 13. PSPD Series type 1 and type 2 units do not require over current protection devices, fuses or circuit breakers to operate correctly. All local and national electric codes must be followed during installation and these codes may require protection of the conductors leading to the PSPD unit.
- Page 9 F F i i g g u u r r e e 3 3 . . N N E E M M A A 1 1 ( ( s s u u f f f f i i x x K K ) ) Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 10 F F i i g g u u r r e e 4 4 . . N N E E M M A A 4 4 - - 4 4 X X ( ( s s u u f f f f i i x x N N , , P P ) ) Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 11 F F i i g g u u r r e e 5 5 . . N N E E M M A A 1 1 ( ( w w i i t t h h d d i i s s c c o o n n n n e e c c t t ) ) ( ( s s u u f f f f i i x x M M ) ) Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 12 F F i i g g u u r r e e 6 6 . . N N E E M M A A 4 4 - - 4 4 X X ( ( w w i i t t h h d d i i s s c c o o n n n n e e c c t t ) ) ( ( s s u u f f f f i i x x O O , , Q Q ) ) ( ( N N E E M M A A 4 4 X X n n o o t t a a v v a a i i l l a a b b l l e e w w i i t t h h P P o o w w e e r r X X p p e e r r t t S S P P D D ) ) Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 13 F F i i g g u u r r e e 8 8 . . S S i i d d e e m m o o u u n n t t F F o o r r m m C C W W i i r r e e s s Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 14 F F i i g g u u r r e e 9 9 . . S S p p l l i i t t P P h h a a s s e e U U n n i i t t s s Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 15 F F i i g g u u r r e e 1 1 0 0 . . 3 3 - - P P h h a a s s e e D D e e l l t t a a Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 16 F F i i g g u u r r e e 1 1 1 1 . . 3 3 - - P P h h a a s s e e W W y y e e U U n n i i t t s s Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 17 Damage will occur to the device if the high leg is not on Phase B. N N O O T T E E Please consult the factory for 240 delta high leg applications with high leg on the ‘C’ phase. Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 18 F F i i g g u u r r e e 1 1 3 3 . . W W i i r r i i n n g g - - S S i i n n g g l l e e p p h h a a s s e e U U n n i i t t s s ( ( 2 2 3 3 0 0 L L ) ) Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
-
Page 19: Operating Features
D D i i s s p p l l a a y y s s a a n n d d I I n n d d i i c c a a t t o o r r s s All Eaton PSPD Series units (Basic, Standard and Standard with Surge Counter) use a display panel to indicate system status. - Page 20 3 3 . . 2 2 . . 3 3 S S t t a a n n d d a a r r d d W W i i t t h h S S u u r r g g e e C C o o u u n n t t e e r r F F e e a a t t u u r r e e P P a a c c k k a a g g e e The Eaton PSPD Series Standard With Surge Counter configuration display panel is shown in Figure F F i i g g u u r r e e 1 1 6 6 .
- Page 21 Place the display back onto the PSPD enclosure. Take care not to overstress or crimp the ribbon cable. Replace the two Phillips head screws. Tighten screws to 1.35 Nm (12 in-lbs). Restore power to the unit. Eaton PSPD Series Installation Manual IM01005032E—Rev 04...
- Page 22 C C h h a a p p t t e e r r 5 5 I I E E C C A A p p p p r r o o v v e e d d M M o o d d e e l l s s Eaton’s one-port low-voltage surge protective device delta models PSPD120480D3M,P SPD160480D3M and PSPD200480D3M meet the requirements of IEC 61643-11 / EN 61643-11, Part 11: Test Class II, and are intended to be installed in applications with a degree of protection rated IP 20.
-
Page 23: Troubleshooting
Table 2 This Troubleshooting Chart identifies possible causes and solutions to the malfunction. Further assistance may be obtained by calling Eaton’s Applications Engineers, at 1-800-809-2772, option 4, sub-option 2, including being directed to the warranty process if applicable. T T a a b b l l e e 2 2 . . T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g C C h h a a r r t t... - Page 24 Relay wire length (optional) 48" of 14AWG extend beyond the conduit hub RoHS Compliant Internal Disconnect (optional) Eaton 30 Amp FDC Circuit Breaker, Type MCCB Input Power Frequency 50/60 Hz, Power Xpert SPD Power consumption (Basic units) 208Y, 240S, 240D, voltage codes 0.5W...
-
Page 25: Specifications
Ordering guidelines for specific models. Warranty 10 years, 15 years if you register on www.eaton.com/spd and then click the warranty registration icon. ROHS compliant Wire length and AWG Factory pre-wired with 48 inches of #10 AWG wire. Eaton PSPD Series Installation Manual IM01005032E—Rev 04... - Page 26 F F i i g g u u r r e e 1 1 7 7 . . E E a a t t o o n n P P S S P P D D S S e e r r i i e e s s ** Eaton’s delta catalog numbers PSPD120480D3M, PSPD160480D3M and PSPD200480D3M meet the requirements of IEC 61643-11 / EN 61643-11, part 11: Test Class II, and are intended to be installed in applications with a degree of protection rated IP 20.
-
Page 27: Warranty
C C h h a a p p t t e e r r 9 9 W W a a r r r r a a n n t t y y Eaton warrants these products for a period of 10 years from the date of delivery to the purchaser, 15 years if you register on www. - Page 28 Warranty In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the use of existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the information, recommendations and descriptions contained herein.
- Page 29 IM01005032E04 IM01005032E 04...
Need help?
Do you have a question about the PSPD Series and is the answer not in the manual?
Questions and answers