Advertisement
Quick Links
Specifications
▪
Compatible underwater housings:
▪
Compatible photo cameras
▪
Compatible TTL strobes:
▪
TTL outputs onboard:
▪
HSS (High Speed Synchronization) support
▪
Flash settings control by camera menu
▪
Flash settings storage in TTL Converter nonvolatile onboard memory, even after power is turned off
▪
Rear / Front Curtain synchronization support:
▪
Continuous shooting mode (CL / CH) support:
▪
Switching "TTL / M" underwater:
▪
(+/-) "Flash Exposure compensation" support:
▪
Switching power "ON/OFF":
▪
Battery type:
▪
Current consumption (in standby mode)
▪
Battery capacity (+20°C):
▪
Fiber-optical cable type:
▪
Compatible Electric Bulkheads (optional accessories):
▪
Electric Sync Cord support (Sea&Sea, Ikelite):
▪
Dual Electric Sync Cord support (Sea&Sea, Ikelite):
11086-HSS Optoelectronic TTL Converter
for ISOTTA underwater photo housings for CANON cameras
(including 2 LEDs)
(Firmware: June-2024)
USER'S MANUAL
Inon Z-330, Z-240, D-200, S-220
Sea&Sea YS-250, YS-D1, YS-D3 Mark II, YSD3-DUO
Ikelite DS-232, DS-230, DS-162, DS-161, DS-160, DS-125
Retra Pro MAX
Marelux APOLLO-III V2.0, APOLLO-S
Subtronic Pro 270, Pro 160
613 cores only (Nauticam 26216 / 26217, HowShot 613L, Sea&Sea 50133 / 50128 / 50135)
(including HSS functionality)
(including HSS functionality)
manual type HSS with Retra and Apollo strobes, - up to 1/8000s
65 000 flashes, 1 year in standby mode
UWTechnics electric M14 bulkheads (Nikonos, S-6, Ikelite)
Isotta
Canon
2 optical + 1 electrical
automatic by camera command
CR2032 (2pcs.)
0.01 mkA
yes
yes
yes
yes
yes
yes
yes
yes
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for UWT 11086-HSS
Summary of Contents for UWT 11086-HSS
- Page 1 11086-HSS Optoelectronic TTL Converter for ISOTTA underwater photo housings for CANON cameras (including 2 LEDs) (Firmware: June-2024) USER’S MANUAL Specifications ▪ Compatible underwater housings: Isotta ▪ Compatible photo cameras Canon ▪ Compatible TTL strobes: Inon Z-330, Z-240, D-200, S-220 Sea&Sea YS-250, YS-D1, YS-D3 Mark II, YSD3-DUO...
- Page 2 Safety Warning for Batteries usage ➢ Use only batteries of the type specified in the Specification. ➢ Batteries must be new and undamaged. Carefully check batteries before usage. ➢ To avoid leakage or explosion, always check appropriate battery terminals position (“plus” terminal up) before installing to the TTL Converter.
- Page 3 TTL Converter battery energy saving ▪ In camera menu please set an acceptable Review Time and Time before going to Standby mode and other timings of camera activity, these are most important settings for TTL-Converter battery saving. When camera is active, TTL Converter is also active and consumes energy from battery.
- Page 4 Flash firing – “Enable” (switch ON the flash) or “Disable” (switch OFF the flash) E-TTL II meter. – Recommended to set “Average” metering type, as initial setting, “Evaluative” type also can be useful with some camera models. Flash sync. speed in Av mode – “1/250 fixed”, “1/60-1/250 auto” or “Auto’ ▪...
- Page 5 Set “1-st curtain” or “2-nd curtain” synchronization type. ▪ Don’t set “HSS” menu option when shooting in TTL mode, - this setting switches system to manual HSS mode even if TTL ▪ option is set. ▪ During the initial test, dependently of concrete camera model, strobes condition etc., photographer should initially adjust (+/-) correction to TTL Flash exposure control.
- Page 6 In such Manual mode also becomes available flash output level scale in submenu. User can adjust flash output level by camera wheel, looking to this menu scale (or looking to camera service screen): Some manual underwater strobes (like MF-1) requires very strong optical signal for synchronization, this case necessary to set maximum power by this scale (1/1).
- Page 7 Continuous (Serial) Shooting using underwater strobes ▪ TTL Converter supports Continuous shooting in all modes, including TTL and M modes. But the main role in this case plays underwater strobes specific (read below). ▪ Compact size underwater strobes like Z-240, Z-330, YS-D1, YS-D3 Mk II etc. have rather weak charger inside, which cannot charge the strobe quick enough between series of TTL doubled flashes (pre-flash + main flash).
Need help?
Do you have a question about the 11086-HSS and is the answer not in the manual?
Questions and answers