Advertisement
Quick Links
Specifications
▪
Compatible underwater housings:
▪
Compatible photo cameras
▪
Compatible TTL strobes:
▪
TTL outputs onboard:
▪
HSS (High Speed Synchronization) support
▪
Flash settings control by camera menu
▪
Flash settings storage in TTL Converter nonvolatile onboard memory, even after power is turned off
▪
Rear / Front Curtain synchronization support:
▪
Continuous shooting mode (CL / CH) support:
Switching "TTL / M" underwater:
▪
▪
(+/-) "Flash Exposure compensation" support:
▪
Switching power "ON/OFF":
▪
Battery type:
▪
Current consumption (in standby mode)
▪
Battery capacity (+20°C):
▪
Fiber-optical cable type:
▪
Compatible Electric Bulkheads (Aquatica original optional accessories):
▪
Electric Sync Cord support (Sea&Sea, Ikelite):
▪
Dual Electric Sync Cord support (Sea&Sea, Ikelite):
11066-HSS Optoelectronic TTL Converter
for AQUATICA underwater photo housings for CANON cameras
(Firmware: June-2024)
USER'S MANUAL
Inon Z-330, Z-240, D-200, S-220
Sea&Sea YS-250, YS-D1, YS-D3 Mark II, YSD3-DUO
Ikelite DS-232, DS-230, DS-162, DS-161, DS-160, DS-125
Retra Pro MAX
Marelux APOLLO-III V2.0, APOLLO-S
Subtronic Pro 270, Pro 160
613 cores only (Nauticam 26216 / 26217, HowShot 613L, Sea&Sea 50133 / 50128 / 50135)
(including HSS functionality)
(including HSS functionality)
manual type HSS with Retra and Apollo strobes, - up to 1/8000s
65 000 flashes, 1 year in standby mode
Aquatica electric bulkheads (Nikonos)
Aquatica
Canon
2 optical + 1 electrical
automatic by camera command
CR2032 (2pcs.)
0.01 mkA
yes
yes
yes
yes
yes
yes
yes
yes
Advertisement
Related Manuals for UWT 11066-HSS
Summary of Contents for UWT 11066-HSS
- Page 1 11066-HSS Optoelectronic TTL Converter for AQUATICA underwater photo housings for CANON cameras (Firmware: June-2024) USER’S MANUAL Specifications ▪ Compatible underwater housings: Aquatica ▪ Compatible photo cameras Canon ▪ Compatible TTL strobes: Inon Z-330, Z-240, D-200, S-220 Sea&Sea YS-250, YS-D1, YS-D3 Mark II, YSD3-DUO...
- Page 2 Safety Warning for Batteries usage ➢ Use only batteries of the type specified in the Specification. ➢ Batteries must be new and undamaged. Carefully check batteries before usage. ➢ To avoid leakage or explosion, always check appropriate battery terminals position (“plus” terminal up) before installing to the TTL Converter.
- Page 3 Recommended time of camera activity, – 15 seconds, or another minimal time allowed by the camera menu. Also, please set a minimum time for viewing image and other similar camera activities. Don’t set “Hold” option in camera menu, it causes fast battery drain. Initial settings for underwater shooting with flash ▪...
- Page 4 ▪ Enter submenu for Synchronization settings: Set “1 curtain” or “2 curtain”, or “HSS” synchronization: Shooting in TTL flash mode ▪ Set main dial switch on the underwater strobe body to TTL mode. Please refer to concrete strobe User Manual to choose an appropriate mode (Z330, Z-240, Retra Pro MAX set to “S-TTL”, YS-D1 set to “DS-TTL”, YS-250/DS-161/DS160 set to “TTL”).
- Page 5 ▪ Set “1-st curtain” or “2-nd curtain” synchronization type. ▪ Don’t set “HSS” menu option when shooting in TTL mode, - this setting switches system to manual HSS mode even if TTL option is set. ▪ During the initial test, dependently of concrete camera model, strobes condition etc., photographer should initially adjust (+/-) correction to TTL Flash exposure control.
- Page 6 Some manual underwater strobes (like MF-1) requires very strong optical signal for synchronization, this case necessary to set maximum power by this scale (1/1). • Special note for YS-D3 DUO strobe usage: TTL Converter’s Flash intensity adjustment by camera controls in this “Controlled Manual mode”...
- Page 7 Continuous (Serial) Shooting using underwater strobes ▪ TTL Converter supports Continuous shooting in all modes, including TTL and M modes. But the main role in this case plays underwater strobes specific (read below). ▪ Compact size underwater strobes like Z-240, Z-330, YS-D1, YS-D3 Mk II etc. have rather weak charger inside, which cannot charge the strobe quick enough between series of TTL doubled flashes (pre-flash + main flash).
Need help?
Do you have a question about the 11066-HSS and is the answer not in the manual?
Questions and answers