Icon Process Controls Truflo UltraFlo UF500 Series Quick Start Manual page 11

Truflo — UltraFlo
®
Clamp-On Ultrasonic Flow Meter Sensor
Calibration Settings
STEPS
Ultrasonic Flowmeter
Main Display
1
Net
1171.325
Ultrasonic Flowmeter
M
Setup Menu
2 05:09:55
Flow (ml/min)
9.500
1171.325
ml
Calibration
3
Measure parameter
0. Pipe 0D: 6.35 mm
1. Pipe THK: 1.00 mm
2. Material : PFA
3. Fluid: Water
Manual totalizer
4. Negative flow : OFF
Flow
0.000
Time
M.T 0.0000
Enter to start ...
Ultrasonic Flowmeter
05:09:55
Setup Menu
4
Flow (ml/min)
9.500
1171.325
ml
25-0613 © Icon Process Controls Ltd.
UF-500S
®
DISPLAY
05:09:55
▶
Flow (ml/min)
0.000 9.500
Net
2467.32
ml
▶
Setup menu
0. Measure parameter
1. System setting
2. Calibration
+
3. Output setting
4. Historical data
5. Manual totalizer
6. System information
▶
System setting Calibration
0. System unit 0. Scale factor : 1.000
1. Flow unit: ml/min 1. 4-20mA Calibrate
2. Total unit: ml 2. Set zero
3. Total RESET 3. Lowflow cut
System information
4. Time set 4. Manual zero
5. System lock : unlock 5. Hi AGC
Ultrasonic Flowmeter
ml/m
6. Damping : 003 6. RTD Calibration
SN:35030200
0.0
7. Linear Correction
s
ON/OFF Times
RunTime
ml
Setup menu
▶
0. Measure parameter
1. System setting
2. Calibration
3. Output setting
4. Historical data
▶
5. Manual totalizer
6. System information
Ultrasonic Flowmeter
05:09:55
Flow (GPM)
Main Display
GAL
Setup menu
3. Output setting
4. Historical data
5. Manual totalizer
Setup Menu
6. System information
7. Language
Select 2. Calibration
8. Energy setting
Note: The flow meter is factory-calibrated.
9. Extern model
Manual totalizer
Flow
0.000
Time
0.0
M.T 0.0000
Calibration
0. Scale factor : Ratio between "actual value" and "reading value".
Enter to start ...
1. 4-20mA Calibrate : Current Loop Calibration. Factory calibrated.
Output setting
2. Set Zero : Calibrates the meter to recognize when no fluid is
0. RS485 Setup
moving through the pipe. –
1. 4-20mA setting
2. Alarm value
3. Lowflow cut : Minimum flow rate threshold below which the
3. OCT output
meter registers the flow as zero.
Language 4. Relay output
5. OCT multiplier
0. English
4. Manual Zero : Actual value adjustment . Factory calibrated.
6. Frequency range
5. Hi AGC : Automatic Gain Control. Select "
V1.11
signal in challenging conditions.
12
2 h
6. RTD Calibration : Resistance Temperature Detector Calibration.
Factory calibrated.
7. Linear Correction : Factory calibrated.
4-20mA setting
0. 4mA Val : 0.00 GPM
1. 20mA Val : 132.0 GPM
2. Model : vs flow
Setup menu
3. Output setting
4. Historical data
5. Manual totalizer
6. System information
7. Language
Back to Setup Menu
8. Energy setting
9. Extern model
(Refer Page 6 for Keypad Functions)
OPERATION
Setup menu
0. Measure parameter
1. System setting
2. Calibration
3. Output setting
4. Historical data
5. Manual totalizer
6. System information
Measure parameter
0. Pipe 0D: 6.35 mm
1. Pipe THK: 1.00 mm
2. Material : PFA
3. Fluid: Water
4. Negative flow : OFF
System information
Ultrasonic Flowmeter
ml/m
SN:35030200
V1.11
s
ON/OFF Times
RunTime
ml
Historical data
0. By Hour
Ent to set Zero | Reset Zero
1. By Day
2. By Month
3. By Year
0.03m/s
4. ON/OFF Time
Measure parameter
0. Pipe 0D: 6.35 mm
1. Pipe THK: 1.00 mm
2. Material : PFA
3. Fluid: Water
4. Negative flow : OFF
Setup menu
3. Output setting
4. Historical data
5. Manual totalizer
6. System information
7. Language
8. Energy setting
9. Extern model
System setting
0. System unit
1. Flow unit: ml/min
2. Total unit: ml
3. Total RESET
4. Time set
5. System lock : unlock
6. Damping : 003
Language
0. English
12
2 h
(Factory Default)
" to amplify the
ON
System setting
0. System unit
1. Flow unit: ml/min
2. Total unit: ml
3. Total RESET
4. Time set
5. System lock : unlock
6. Damping : 003
Calibrati
0. Scale f
1. 4-20m
2. Set zer
3. Lowflo
4. Manua
5. Hi AG
6. RTD C
7. Linear
Calibrati
0. Scale f
1. 4-20m
2. Set zer
3. Lowflo
4. Manua
5. Hi AG
6. RTD C
7. Linear
11