Raspberry Pi 4 B User Manual page 4

uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this
product for environmentally safe recycling.
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
FCC
Raspberry Pi 4B FCC ID: 2ABCB-RPI4B
This device complies with part 15 of the FCC Rules. Operation is
subject to the ollowing two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION
Any changes or modications to the equipment not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment. This equipment has
been tested and found to comply within the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Re-orient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a different circuit
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician
for help.
For product available in the USA/Canada market, only channel
1–11 can be operated and these channel assignments deal with
only the 2.4GHz range.
This device and its antenna(s) must not be co-located or
operated in conjunction with any other antenna or transmitter
except in accordance with FCC's multi-transmitter procedures. If
this device is operated in the 5.15–5.25GHz requency range, then
it is restricted to an indoor environment only.
IMPORTANT NOTE
FCC Radiation Exposure Statement: Co-location of this module
with another transmitter that operates simultaneously is required
to be evaluated using the FCC multi-transmitter procedures.
This device complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. The device contains an
integral antenna, hence the device must be installed such that
there is a separation distance of at least 20cm from all persons.
LABEL OF THE END PRODUCT
The nal end product must be labelled in a visible area with the
following: "Contains TX FCC ID: 2ABCB-RPI4B". I the size o the
end product is larger than 8×10cm, then the following FCC part
15.19 statement must also be available on the label:
"This device complies with part 15 of the FCC Rules.
Operation is subject to the ollowing two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
intererence that may cause undesired operation."
ISED
Raspberry Pi 4B IC: 20953-RPI4B
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the ollowing two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conorme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1. L'appareil ne doit pas produire de brouillage.
2. L'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
For product available in the USA/Canada market, only channels 1
to 11 are available or 2.4GHz WLAN. Selection o other channels
is not possible.
Pour les produits disponibles sur le marché USA / Canada, seuls
les canaux 1 à 11 sont disponibles pour le réseau local sans l 2,4
GHz. La sélection d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co-located with
any other transmitters except in accordance with IC multi-
transmitter product procedures. Referring to the multi-transmitter
policy, multiple-transmitter(s) and module(s) can be operated
simultaneously without reassessment permissive change.
Cet appareil et son antenne/ses antennes ne doivent pas être
co-localisés avec un autre émetteur, sau en conormité avec les
procédures de Industry Canada pour les produits multi-émetteurs.
En se réérant à la politique multi-émetteurs, plusieurs émetteurs
et modules peuvent être utilisés simultanément sans réévaluation
pour changement permissif.
The device or operation in the band 5150–5250 MHz is only or
indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems.
Les dispositis onctionnant dans la bande 5150-5250 MHz sont
réservés uniquement pour une utilisation à l'intérieur an de
réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux.
IMPORTANT NOTE
IC RADIATION EXPOSURE STATEMENT
This equipment complies with IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum separation
distance of 20cm between the device and all persons.
Cet équipement est conorme aux limites d'exposition au
rayonnement IC RSS-102 dénies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec une
distance de séparation minimale de 20 cm entre l'appareil et
toutes les personnes.
INTEGRATION INFORMATION FOR THE OEM
It is the responsibility of the OEM / Host product manufacturer
to ensure continued compliance to FCC and ISED Canada
certification requirements once the module is integrated in
to the Host product. Please refer to FCC KDB 996369 D04 for
additional inormation. The module is subject to the ollowing
FCC rule parts: 15.207, 15.209, 15.247, 15.403 and 15.407
HOST PRODUCT USER GUIDE TEXT
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation
is subject to the ollowing two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that causes undesired operation.
CAUTION
Any changes or modifications to the equipment not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply within
the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
1. Re-orient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a different circuit
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician
for help.
For products available in the USA/Canada market, only
channels 1 to 11 are available or 2.4GHz WLAN. This device
and its antenna(s) must not be co-located or operated in
conjunction with any other antenna or transmitter except in
accordance with FCC's multi-transmitter procedures. This
device operates in the 5.15–5.25GHz requency range and is
restricted to indoor use only.
ISED CANADA COMPLIANCE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the ollowing two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conorme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1. L'appareil ne doit pas produire de brouillage.
2. L'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
For products available in the USA/Canada market, only channels
1 to 11 are available or 2.4GHz WLAN Selection o other channels
is not possible.
Pour les produits disponibles sur le marché USA / Canada, seuls
les canaux 1 à 11 sont disponibles pour le réseau local sans l 2,4
GHz. La sélection d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co-located with any
other transmitters except in accordance with IC multi-transmitter
product procedures.
Cet appareil et son antenne/ses antennes ne doivent pas
être co-localisés avec un autre émetteur, sau en conormité
avec les procédures de Industry Canada pour les produits
multi-émetteurs.
The device or operation in the band 5150–5250 MHz is only or
indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems.
Les dispositis onctionnant dans la bande 5150-5250 MHz sont
réservés uniquement pour une utilisation à l'intérieur an de
réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux.
IMPORTANT NOTE
IC RADIATION EXPOSURE STATEMENT
This equipment complies with IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum separation
distance of 20cm between the device and all persons.
Cet équipement est conorme aux limites d'exposition au
rayonnement IC RSS-102 dénies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec une
distance de séparation minimale de 20 cm entre l'appareil et
toutes les personnes.
HOST PRODUCT LABELLING
The host product must be labelled with the following information:
"Contains TX FCC ID: 2ABCB-RPI4B"
"Contains IC: 20953-RPI4B"
"This device complies with part 15 of the FCC Rules. Operation is
subject to the ollowing two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
intererence that cause undesired operation."
IMPORTANT NOTICE TO OEMS:
The FCC Part 15 text must go on the Host product unless the
product is too small to support a label with the text on it. It is not
acceptable just to place the text in the user guide.