Advertisement
Table of Contents
Attention:
The StarBright™ 14 is composed of high quality sensitive multi-layer projection material. Please follow the
precautions below for proper care procedures and to prolong the life of your screen.
Note: Upon unrolling the StarBright™ 14 material, it may exhibit faint vertical memory lines from being rolled up.
These lines will fade out and disappear once the material is properly installed onto the framework.
Failure to use [these safeguards] will result in voiding your warranty.
1.
Avoid using any organic cleaning agents or harsh abrasives, which will result in permanently damaging
the screen material.
2.
Use only a soft-feathered brush or microfiber cloth to spot clean and remove dust.
3.
Please wear a pair of clean, powder-free glove in the process of installing and operating the screen to keep
hand oil and dirt from being transferred to the viewing surface.
4.
Be very careful when unrolling and handling the material. Lay the material flat only to avoid permanently
creasing the material.
5.
Do not rub the cloth with force when cleaning to avoid permanently damaging the surface.
6.
Do not touch the screen surface with sharp objects or allow the screen surface to come in contact with
anything other than the frame.
7.
StarBright™ 14 material damaged in handling, installation, or use is not covered under warranty.
a: Frame parts x 6 pcs
(Springs pre-installed)
j: Gloves x 2 pcs
i: Center support bar x 1 pc
※ Gloves (j) and Protection sheet (k) may not be included in some specific models.
Note: Please make sure all parts are included in your package before proceeding to assemble the fixed
frame screen.
Rev 1/27/2025 BR
Sable Frame StarBright™ 14 Series
Ceiling Ambient Light Rejecting Fixed Frame Screen
Hardware and Parts List
b:
Elbow Joints x 8 pcs
f: M5*50 wood screws x 8 pcs
k: Protection sheet x 1 pc
www.elitescreens.com
For standard (long) throw projectors
User's Guide – Version 2.0
c: M5*6 screws x 40 pcs
g: Wall anchor x 8 pcs
L: Screen Material x 1 pc
d: Springs hook x 2 pcs
h: Wall brackets x 4 pcs
M: Center Joints x 2 pcs
1
Advertisement
Table of Contents
Related Manuals for Elite Screens Sable Frame StarBright 14 Series
Summary of Contents for Elite Screens Sable Frame StarBright 14 Series
- Page 1 Sable Frame StarBright™ 14 Series Ceiling Ambient Light Rejecting Fixed Frame Screen For standard (long) throw projectors User’s Guide – Version 2.0 Attention: The StarBright™ 14 is composed of high quality sensitive multi-layer projection material. Please follow the precautions below for proper care procedures and to prolong the life of your screen. Note: Upon unrolling the StarBright™...
-
Page 2: Frame Assembly
Frame Assembly 1. If gloves (j) were included in the package, please put them on before installation begins. 2. Insert the center joint (m) connector into to one of the 1/2 horizontal frames and fasten it with two M5*6 screws (c). - Page 3 Attaching the screen material to the frame 1. Carefully unroll a small area of the material over the frame as shown below and secure the top and bottom corners by hooking them with two springs on the corner of the material (1), Then hook and secure the springs in the middle (2).
-
Page 4: Center Support
3. Continue unrolling the entire material to the other end, hook the springs in the corners (4) and hook the springs in the middle (5). Center Support Bard Insert the support joiner into each end of the center support bar to complete assembly. support joiner Center support bar Insert the Center Support Bar into the upper top groove on the back of the frame (not the groove where the... -
Page 5: Notice To Installer
4. Once the center support bar is inserted, attach the remaining springs to the material in steps 6-13 in the following order. Notice to Installer: Please use the following installation instructions to obtain superior optical performance from the Retro Reflective CLR/ALR (Ceiling Ambient Light Rejecting) StarBright™ 14 Screen. Projector placement Note: Do not install the projector at an angle that is greater than 5°... -
Page 6: Installation
Installation 1. Measure the overall length and height of the frame and drill holes for the top bottom brackets. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a screwdriver. - Page 7 7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other sharp or abrasive objects. 8. Spare Parts should be placed out of reach of small children in accordance with household safety guidelines. For a local Elite Screens contact or Technical Support, please visit www.elitescreens.com Rev 1/27/2025 BR...
Need help?
Do you have a question about the Sable Frame StarBright 14 Series and is the answer not in the manual?
Questions and answers