Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Future Automation Manuals
  4. TV Mount
  5. AL965
  6. Installation instructions manual

Future Automation AL965 Installation Instructions Manual

Hide thumbs Also See for AL965:

Advertisement

Quick Links

Download this manual
AL 9 6 5
TV A CTU A TOR L I F T 5 0 " - 6 5 "
I N S TA L LA T I O N
I N ST R U CTI ON S
I SSUE 016

Advertisement

loading
Need help?

Need help?

Do you have a question about the AL965 and is the answer not in the manual?

Questions and answers

Related Manuals for Future Automation AL965

Summary of Contents for Future Automation AL965

  • Page 1 AL 9 6 5 TV A CTU A TOR L I F T 5 0 ” - 6 5 ” I N S TA L LA T I O N I N ST R U CTI ON S I SSUE 016...

  • Page 3: Sa Fety Di Sc La Imer

    Clean only with a dry cloth and always unplug any electrical items being used in conjunction with this product before cleaning. Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as possible. However, Future Automation makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
  • Page 4 Under the warranty, Future Automation aims to either solve the issue remotely (via telephone or email support) or if the mechanism requires a part, arrange a visit to your premises by a Future Automation approved engineer or send replacement items where appropriate.

  • Page 5: Table Of Contents

    GUI D E C O NT E NTS SAFE TY DISCLA IM ER PR OD UCT WA RR A NT Y & RISK ASSESS M EN T GUIDE C ONT ENTS PACKA GE CONTENT S MECH ANISM QUICK-ST A RT GUI D E INITIAL OP ERA TION CABINET MOUNTING SCRE EN BRA CKET FIT TING...

  • Page 6: Package Contents

    PACKAG E CONT ENTS 1 - AL965 1.1 - BASE PLATE 1.2 - LINEAR ACTUATOR 1.3 - BASE SHELF BRACKET 1.4 - PUSH BARS (X2) 1.5 - FIXED FLAP MOUNTING BRACKET (X2) 1.6 - FIXING PLATE 1.7 - UPRIGHT SUPPORT BRACKET 2 - FB49 2.1 - UPRIGHTS (X2)
  • Page 7 MEC HA NI SM QUI CK - S TART GUI DE Some Future Automation mechanisms may ship with the control box disconnected to prevent damage during transit. In order to operate the mechanism, the control box will need to reconnected, then have mains power applied along with the desired control method.

  • Page 8: Initial Op Era Tion

    INI T I A L OPER A T ION • Unpack and check the mechanism fully for any damage or obvious visual faults before operation. • Test the mechanism by running it fully up and down once (refer to the mechanism control section of the instructions for more details)

  • Page 9: Cabinet Mounting

    • Double check the cabinet measurement against the latest AL965 technical sheet • Place the AL965 mechanism into the cabinet and fix down via the bottom and rear fixing holes indicated below (fixings not supplied). • Secure the AL965 cable management chain to the rear of the cabinet (fixings not supplied).

  • Page 10: Scre En Bra Cket Fit Ting

    SCR EEN BRACKE T F ITT IN G • Located the push rollers on the side of the main body, and fix in place using the supplied countersunk washers and M6 x 12mm countersunk bolts. Follow the same process for mounting the fixed flap brackets.

  • Page 11: She Lf Fitt Ing

    • Check the base shelf dimensions against the latest AL965 technical sheet. • Place the base shelf onto the shelf bracket and fix from the underside (fixings not provided).

  • Page 12: Scre En Alignment 1

    • With the mechanism in the IN position, offer the screen up to the AL965 and position it so that the top of the screen sits at least 5mm [3/16”] below the underside of the cabinet lid.

  • Page 13: Scre En Mou Nt Ing 1

    SCREEN M OU NTIN G • Remove the star nut and insert the supplied rubber buffer into the screen upright and use the M5 half nut to lock it in place (repeat this for the other upright). • Lay the screen down on a safe surface and place the screen uprights on to the screens VESA holes.

  • Page 14: Push Bar A Djust Ment 1

    P US H BAR ADJU S T MEN T • When the mechanism opens, the push bar should be in contact with the flap at all times • The flap should not open past 90°. • Instructions for adjusting the push rollers can be found below.

  • Page 15: Final Checks 1

    FIN A L CH EC K S • Make sure the AL965 opens and closes fully without any interference from the cabinet. • Make sure the flap opens and closes smoothly and the push rollers contact the flap correctly. •...

  • Page 16: Ge Ner A L Cont Rol 1

    REPLACING MECHANISM BATTERIES The standard Future Automation Infrared (IR) remote control required x2 AAA batteries to operate. These are provided with the mechanism in the Accessories Pack. These batteries can be replaced as the per the image below.

  • Page 17: Infrar Ed (Ir)

    INF RA RE D (I R) This mechanism can be controlled via the supplied 14 button Infrared (IR) Remote Control, paired with the supplied Infrared (IR) lead and sensor. The mechanism's functions can be controlled by plugging the Infrared (IR) lead and sensor into the 3.5mm IR Input Jack shown on the General Mechanism Control page.

  • Page 18: Rad Io F Requency (R F)

    RA D I O F RE QUEN CY (RF) If purchased with the Radio Frequency (RF) control option, this mechanism can be controlled via the supplied 4 button Radio Frequency (RF) Remote Control, paired with the in-built Radio Frequency (RF) sensor. Confirmation of Radio Frequency (RF) input will be shown by a single flash of the large green LED located on the end of the control box.

  • Page 19: Conta Ct Closu

    C ONT ACT C LOSURE This Mechanism can be controlled via Contact Closure, utilising an 8 Pin RJ45 Connector attached to a length of CAT5 (Type 568A or 568B) cable. The mechanism’s functions can be controlled by plugging this into the RJ45 port on the mechanism control board, then shorting pins 1-8 on this connector as shown in the Contact Closure Input Table below.

  • Page 20: Rs232 Cont Rol 1

    RS2 32 CON T RO L This Mechanism can be controlled via RS232, utilising a 6 Pin RJ11/RJ25 connector OR 9 Pin Serial connector attached to a length of 6 core cable. The mechanism's functions can be controlled by plugging this into the RJ11/RJ25 port on the mechanism control box, then inputting the RS232 commands shown in the RS232 Input Table below.
  • Page 21 NO T E S :...
  • Page 22 NO T E S :...
  • Page 23 NO T E S :...
  • Page 24 EUROPEAN OFFICE NORTH AMERICAN OFFICE Address: Address: Unit 6-8 Enterprise Park Brunel Road 127 Venture Drive Bedford Dover Bedfordshire MK41 9TG 03820 Phone: +44 (0) 1438 833577 Phone: +1 (603) 742 9181 Email: info@futureautomation.co.uk Email: info@futureautomation.net Office Hours: Office Hours: Mon - Fri 8:00 to 17:30 GMT Mon - Fri 7:00 to 17:00 EST Saturday &...