GreenWorks SNB401 Operator's Manual

Hide thumbs Also See for SNB401:

Operator's manual (44 pages)

Operator's manual (17 pages)

Table Of Contents

Quick Links

Download this manual

2601302

SNOW THROWER

OPERATOR MANUAL

SNB401

www.greenworkstools.com

Table of Contents

Need help?

Do you have a question about the SNB401 and is the answer not in the manual?

Questions and answers

Summary of Contents for GreenWorks SNB401

Page 1 2601302 SNOW THROWER OPERATOR MANUAL SNB401 www.greenworkstools.com...
Page 3: Table Of Contents
English Install the chute deflector......8 Description.........4 Install the chute control rod......8 Purpose........... 4 Install the battery pack......9 Overview..........4 Remove the battery pack......9 General power tool safety Operation........9 warnings........4 Cold weather operation......9 Training............ 4 Start the machine........10 Preparation..........
Page 4: Description
English The term “power tool” in the warnings refers to your DESCRIPTION battery-operated (cordless) power tool. TRAINING PURPOSE This machine is used to remove and clear away snow • Do not allow children under the age of 14 to operate from pavements, gardens, driveways and other ground- this tool.
Page 5: Operation
English • When battery pack is not in use, keep it away from • Never operate the appliance without good visibility the following metal objects: paper clips, coins, keys, or light. Always be sure of your footing, and keep a nails, screws, and other small metal objects that can firm hold on the handles.
Page 6: Recommended Ambient Temperature Range
English the specified range may damage the battery and Symbol Explanation increase the risk of fire. • Recharge only with the charger speciﬁed by the Wear eye protection. manufacturer. A charger that is suitable for one type of battery pack may create a risk of ﬁre when used Thrown objects can ricochet and with another battery pack.
Page 7: Environmentally Safe Battery Disposal
English ENVIRONMENTALLY SAFE PROPOSITION 65 BATTERY DISPOSAL WARNING This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
Page 8: Install The Upper Handle
English INSTALL THE UPPER HANDLE INSTALL THE CHUTE DEFLECTOR 1. Align the holes in the middle handle and the upper 1. Align the tabs with the slots on one side first. handle. 2. Push the chute deflector. 2. Insert the bolt through the middle handle and upper handle.
Page 9: Install The Battery Pack
English 4. When you hear a click, the battery pack is installed. 5. Close the battery door. REMOVE THE BATTERY PACK 6. Turn the grip handle left and right to make sure that 1. Open the battery door. the discharge chute moves in the same direction. 2.
Page 10: Start The Machine
English If the machine does not start: WARNING • remove the battery pack from the machine, Wait until the impeller fully stops before you start the • charge the battery pack to 15 minutes in warm area, machine again. Do not quickly turn the machine off or when the charging light turns green.
Page 11: Led Headlights
English • When you complete the work, let the machine operate for a while to prevent ice formation in the discharge chute. • If the snow is deeper than 8", decrease the speed and let the machine work at its own rhythm. •...
Page 12: Replace The Impeller
English 4. Reinstall the mounting screws and spacers and tighten them. REPLACE THE IMPELLER WARNING Use only approved replacement scrapers. 1. Remove the 5 screws and side wear pad that secure the right side cover. 2. Remove the nut. 2. Remove the mounting screws and spacers and discard the old scraper.
Page 13 English 4. Remove the belt. 6. Remove the screws that secure the left side plate. 5. Using a socket wrench, remove the large pulley. 7. Pull the axle and remove the old impeller, install the new impeller.
Page 14: Store The Machine
English • Make sure the motor is not hot when you store the machine. • Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions: • Replace the damaged parts. •...
Page 15: Troubleshooting
English Impeller size 16 in. (40.6 cm) TROUBLESHOOTING Weight (without battery 15.3 Kg (33.8 Ibs) and charger) Problem Possible cause Solution Battery 2901302, BAB742 and The handle is The bolts are not Adjust the height other BAB series and oth- not in position.
Page 16 It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks. USA address: Greenworks Tools P.O. Box 1238, Mooresville, NC 28115 Canadian address: Greenworks Tools Canada, Inc.
Page 17 www.greenworkstools.com P0801132-04 Rev B...

This manual is also suitable for: