Graco FOAM-CAT@ 200 Instructions-Parts List Manual
Hide thumbs
Also See for FOAM-CAT@ 200:
- Instructions-parts list manual (24 pages) ,
- Instructions manual (22 pages) ,
- Instructions and parts list (44 pages)
Table of Contents
Advertisement
Quick Links
INSTRUCTIONS-PARTS LIST
This manual
contains
WARNINGS
and
AND
READ
RETAIN FOR REFERENCE
Air Powered
FOAM-CAT@ 200 SPRAYER
MAXIMUM WORKING PRESSURE
240 Volt, 1 or 3 Phase, 5 0 / 6 0 Hz
Delivery
15 Ib/min at
temperature rise.
(6.75 Kg/min at 27OC temperature rise.)
Power Requirements
Electrical:
240
Volt Maximum
208
Volt
Minimum
Single phase:
37 Amos with 315 ft (91.4
Three phase:
27 Amps with '315
Compressed Air: 80-120 psi (5.6-8.3 bar)
CFM (0.84 m3/min)
Model 226-991 Includes:
Foam-Cat Heater and Heated Hose Controls
President Plural Component Pump
Pump Stand
ft
15
(4.6
ft
Spray Gun with 0.089 in. (2.26 mm) Dia. Nozzle Kit
Model
Same as 226-991 except does not include the
15 ft heated hose.
Reactive Chemical Hazard
Graco Inc. does not manufacture or supply any of the reactive chemical materials that may be used in this equip-
ment and is not responsible for their effects. Because of the vast number of chemicals that could be used and
their varying chemical reactions, before using this equipment, the buyer and the user should determine all facts
relating to the materials used, including any
posure of human beings to the individual components or their resultant mixtures. Gram assumes no respon-
from the use of such chemical components.
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444
IMPORTANT
INSTRUCTIONS
hose
ft
(91.4 m) hose
ft
or
WARNING
o f
the potential hazards involved. Particular inquity and investiga-
Rev E
SUPERSEDES
0
Advertisement
Table of Contents
Related Manuals for Graco FOAM-CAT@ 200
Summary of Contents for Graco FOAM-CAT@ 200
- Page 1 Reactive Chemical Hazard Graco Inc. does not manufacture or supply any of the reactive chemical materials that may be used in this equip- ment and is not responsible for their effects. Because of the vast number of chemicals that could be used and...
- Page 2 If you are using other similar ac- cessories, refer to the instructions received with that CAUTION: Alerts user to avoid or correct conditions equipment. Graco accessories are listed the back that could damage or destroy equipment.
- Page 3 HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. OBSERVE FOR PROFESSIONAL ONLY. ALL W A R N I N G S . Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General S a f e t y This equipment generates very high fluid pressure.
- Page 4 Doing causes ex- cessive heat buildup which can result in hose rupture end system are designed to be used only with Graco Foam-Cat Heated Hoses. Models 216-613 and 218614. NEVER anempt cause serious bodily injury; including injection, and property to connect other hoses to this heater.
-
Page 5: Reference Numbers
Air Rewlator or Air Valve Heated Hose 9 Air Drfer Foam-Cat contact your Graco representative. Air Drfer Ring Pump Stand Air Hose, Feed Pump Kit Y-Line Strainer Main Air Supply to Dryer Fluid Hose, Disp. Pump to Control Box Cable. -
Page 6: Installation
INSTALLATION Connect en air supply hose (11) from the 1. Secure the sprayer stand (2011 to the floor in a suitable location. Refer to the mounting hole diagram in manual 307-551. pump to the air manifold See the Typical In- stallation. - Page 7 Assemble the main heated hoses 1102). Connect the corresponding fluid hoses of each foot b. A few inches back from the heat tape connec- tors, bend the heat tape ON BOTH SIDES OF CONNECTORS to take up slack. See Fig Then couple the heat tapes.
- Page 8 10. Connect the heated hose assembly (102 8 103) to the heaters and heated hose control See Fig 5. Connect the fluid hoses to the corresponding b. Connect the heat tape (16) of the whip hose to the hose control box cable c.
- Page 9 Fig 10 Guide the needle of the nozzle assembly into TRIGGER TRIGGER SHOWN IN SHOWN the front opening (38) the gun body "ON- SAFE "OFF- SAFE The socket of the piston rod (39) must face POSITION POSITION down. Tilt the nozzle assembly up, and swing the ball the needle into the piston rod...
- Page 10 Connect the feed hose t o the displacement To ground the heater and heated hoses: pumps. Slide an identification band (IS0 or RES) c. Wire the heater to a positively grounded power supply In a mobile installation, be sure the truck over the end of each feed hose (45).
-
Page 11: Operation
OPERATION WARNING Be sure the heater and heated hose circuit breakers are shut off to reduce the risk of electric shock. See Fig 21, page 12. sprayer and check for leaks at all fluid 1. Prime the connections. a. Close the feed pump air inlet valves or regulators See the Typical Installation on page... - Page 12 i. Open the feed pump air valves (8). Refer to the Pressure Relief Procedure Typical Installation. Always relieve the fluid pressure in the sprayer and hoses before checking or adjusting any part of Prime the hoses. the system or any component, to reduce the risk of serious bodily injury, including fluid injection, manifold, hold the manifold (27) so each splashing in the eyes or on the skin, or injury from...
- Page 13 d. Wrap the insulation tubing (68) around the hose connections, overlapping it at the seam. and starting at the gun manifold pull Wrap tape (69) continuously around the tubing, couple of inches of the cover over the hose and beginning and ending about 2 inches (51 mm) tape in place.
- Page 14 M A X e. Set the heated hose ATC MED. NOTE: Graco recommends always using the hose 115°F ATC even if the heater ATC is not used. The first time you use the heater, operate it without using the heater ATC .Check the...
- Page 15 7 . Test the spray pattern. Aim the gun at e piece of scrap cardboard and trigger for 1 second to check the spray pattern. A good pattern should be round and well atomized, and it should harden with a fairly smooth surface.
- Page 16 NOTES: 307-542...
-
Page 17: Parts Drawing
PARTS DRAWING Model without heated hoses Includes items 101, 104, 105 307-542... -
Page 18: Parts List
LIST PARTS Basic Sprayer Components REF PART DESCRIPTION REF PART DESCRIPTION NO. NO. parts) nent (see for Darts) 101078 STRAINER, "Y"; mesh 3/8 npt(m x f ) screen; 3/4 npt(fbe) Includes item 180-199 .ELEMENT, filter, mesh screen 100-101 CAPSCREW, hex hd; 3/8 npt x 1"... -
Page 19: How To Order Replacement Parts
2. Check the parts list identify the correct part number; do not use the ref. no. when ordering. Order all parts from your nearest Graco distributor. 6 digit PART PART DESCRIPTION NUMBER... -
Page 20: Service Information
GRACO MAKES NO WARRANTY, AN0 DISCLAIMS ALL IMPLIED WARRANTIES MERCHANTABILITY AND FITNESS FOR A PAR- TURED BY GRACO. These items sold. but not manufactured bv Graco [such as electric motor. switches. hose. etc.1. Era subiect to the warran- t y , any, oftheir manufacturar.
Need help?
Do you have a question about the FOAM-CAT@ 200 and is the answer not in the manual?
Questions and answers