Hakko Electronics FX100-53 Instruction Manual
  1. Manuals
  2. Brands
  3. Hakko Electronics Manuals
  4. Soldering Gun
  5. FX100-53
  6. Instruction manual
Hakko Electronics FX100-53 Instruction Manual

Hakko Electronics FX100-53 Instruction Manual

Hide thumbs

Advertisement

Table of Contents

www.valuetronics.com
Instruction Manual
Thank you for purchasing the HAKKO FX-100 Soldering Station.
Please read this manual before operating the HAKKO FX-100.
Keep this manual readily accessible for reference.
1. PACKING LIST AND PART NAMES*
HAKKO FX-100 soldering station
HAKKO FX-1001 soldering iron
Sleeve (Green)
Sleeve (Gray)
Cleaning wire
HAKKO FX-100
Soldering station
Receptacle
he packing list for FX100-53 will be HAKKO FX-100 soldering station, Power cord and Instruction manual
* T
only.
2. COMPATIBLE MODELS
Use this product with the following models.
• FX-1001 (Soldering Iron) T31 series (tip for FX-1001)
• FX-1002 (Micro Soldering Iron) T35 series (tip for FX-1002)
3. SPECIFICATIONS
Power consumption
28 - 85 W
Tip series /
T31-01 Series / 450℃ (840℉)
T31-02 Series / 400℃ (750℉)
Tip temperature
T31-03 Series / 350℃ (660℉)
Temperature stability
±1.1℃ (±2.0℉)
 Station
Output power
50 W
Output frequency
13.56 MHz
Dimensions
127 (W) × 150 (H) × 167 (D) mm
(5.0 × 5.9 × 6.6 in.)
Weight
3 kg (6.6 lb.)
* Specifications and design are subject to change without notice.
* Specifications and design are subject to change without notice.
This device complies with Part 18 of the FCC Rules.
This device complies with Part 18 of the FCC Rules.
CAUTION
This product includes such features as electrically conductive plastic parts and grounding of the handpiece
and station as measures to protect the device to be soldered from the effects of static electricity. Be sure to
observe the following instructions:
1. The handle and other plastic parts are not insulators, they are conductors. When replacing parts or
repairing, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
Soldering Station
Please check to make sure that all items listed
below are included in the package.
1
Heat resistant pad
1
Iron holder
1
Power cord
1
Instruction manual
1
HAKKO FX-1001
Soldering iron
Cleaning wire
Cleaning
Power switch
sponge
Heat resistant
pad
 HAKKO FX-1001 soldering iron
Cord
Total Length (w/o cord)
Weight (w/o cord)
NOTE:
This product is protected against electrostatic discharge.
1
1
1
1
Power cord
Sleeve
Sleeve
(Green)
(Gray)
Iron holder
Iron holder
base
1.3 m (4.3 ft.)
190 mm (7.5 in.) with T31-02D24 tip
31 g (0.07 lb.) with T31-02D24 tip

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FX100-53 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hakko Electronics FX100-53

Summary of Contents for Hakko Electronics FX100-53

  • Page 1 Soldering station Receptacle Iron holder base he packing list for FX100-53 will be HAKKO FX-100 soldering station, Power cord and Instruction manual only. 2. COMPATIBLE MODELS Use this product with the following models. • FX-1001 (Soldering Iron) T31 series (tip for FX-1001) •...

  • Page 2: Warnings, Cautions, And Notes

    4. WARNINGS, CAUTIONS AND NOTES Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s attention to significant items. They are defined as follows: WARNING: Failure to comply with a WARNING may result in serious injury or death. CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved.

  • Page 3: Initial Setup

    5. INITIAL SETUP A. Iron holder large sponge  This product includes two methods for cleaning the tip: a wire tip cleaner, and a sponge. Please be sure to soak the sponge in water before using. 1. Set the iron holder. small sponge 2.
  • Page 4 5. INITIAL SETUP ■ How to replace the sleeve 1. Turn the sleeve assembly counterclockwise and remove it from the handle. Counterclockwise 2. Remove the sleeve as shown in the diagram below. NOTE: A small o-ring is placed inside the sleeve assembly and may fall out when you remove the sleeve assembly.

  • Page 5: Operation

    6. OPERATION ● Operation 1. Turn ON the power switch. 2. The screen will switch in order of product number indication → greeting → home screen. 3. When the home screen is displayed, the MODE status is indicated on the left and output graph at the center.
  • Page 6 6. OPERATION ・When DSP (Display) is pressed The selected information will be displayed on the screen. The cursor moves by pressing the <↑> or <↓> ＳＨＯＷ ＰＲＯＦＩＬＥ button. The following items are displayed in order. ・ＳＨＯＷ ＰＲＯＦＩＬＥ ＳＨＯＷ ＴＩＰ ＬＯＡＤＳ ・ＳＨＯＷ ＴＩＰ ＬＯＡＤＳ ・ＳＨＯＷ ＴＩＰ ＴＩＭＥ ＳＨＯＷ ＴＩＰ ＴＩＭＥ ・ＳＥＬＥＣＴ ＰＲＯＦＩＬＥ ＜↑＞  ＜↓＞  ＜ＯＫ＞ ・ＴＩＰ ＴＹＰＥ ・＜ＣＡＮＣＥＬ＞ SHOW PROFILE The set profile information (Station, User, and Solder) is displayed. ＰＲＯＦＩＬＥ １ ＰＲＯＦＩＬＥ １ ＳＴＡＴＩＯＮ ＩＤ Ｓ：○○○○○ ＵＳＥＲ ＮＡＭＥ Ｕ：×××××× ＳＯＬＤＥＲ ＴＹＰＥ...

  • Page 7: Parameter Setting

    6. OPERATION TIP TYPE The tip type (450°C, 400°C, 350°C) is displayed. • When MANUAL SET is selected When MANUAL SET is selected, the screen changes to the one as shown in the lower right figure. Select an appropriate number according to the tip to be used. Then, the tip type is displayed so that the tip type is clearly known.
  • Page 8 7. PARAMETER SETTING DISPLAY The fashion in which the output graph is displayed can be changed. NORMAL: Histogram (rolling bar graph), EXPAND: Horizontal expanding graph, OFF: No display DISPLAY screen  When NORMAL is selected  ＮＯＲＭＡＬ ＥＸＰＡＮＤ Ｎ ＯＦＦ ＜↑＞  ＜↓＞  ＜ＯＫ＞ When OFF is selected When EXPAND is selected     Ｎ Ｎ ＬＯＣＫ Displayed when password lock is set  AUTO SLEEP The automatic sleep period can be set up. Sleep function is canceled by removing the solder iron from the  holder or pressing one of the 3 buttons. Setting AUTO SLEEP ＡＵＴＯ ＳＬＥＥＰ ＳＥＴ In the AUTO SLEEP mode, you can set the sleep     ０１ｍｉｎ time between 01 to 29 minutes. When 00 is set,  the sleep function is OFF     ＜↑＞  ＜↓＞  ＜ＯＫ＞ AUTO SHUTOFF The time to automatically turn off the soldering station can be set up. Electricity is stopped automatically when the solder iron is not used for the set period of time. SHUTOFF function is canceled by pressing one of the 3 buttons. Setting AUTO SHUTOFF ＡＵＴＯ−ＳＨＵＴＯＦＦ ＳＥＴ When the SHUT OFF time is set, the power     ＮＯＷ：３０ｍｉｎ supply stops when the soldering iron is not ...
  • Page 9 7. PARAMETER SETTING PROFILE The profile information can be set up. STATION ID: Station name, Asset ID, etc., PROFILE1,2: User name and solder information. PROFILE screen When STATION ID is selected ＳＴＡＴＩＯＮ ＩＤ ＳＴＡＴＩＯＮ ＩＤ ＰＲＯＦＩＬＥ １ 〔              〕 ＰＲＯＦＩＬＥ ２ ＜↑＞  ＜↓＞  ＜ＯＫ＞  ＜↑＞  ＜↓＞  ＜ＯＫ＞ When PROFILE1 (2)  is selected When USER NAME is selected ＵＳＥＲ ＮＡＭＥ ＰＲＯＦ．１ ＵＳＥＲ ＳＯＬＤＥＲ ＴＹＰＥ 〔              〕 ＜ＣＡＮＣＥＬ＞ ＜↑＞  ＜↓＞  ＜ＯＫ＞  ＜↑＞  ＜↓＞  ＜ＯＫ＞ When SOLDER TYPE is selected You can make your name and ID from  A-Z ,  ＰＲＯＦ．１ ＳＯＬＤＥＲ 0-9 ,  . ,  -  and space. You can enter  〔              〕 up to 14 letters. This is blank in the initial setting.   ＜↑＞  ＜↓＞  ＜ＯＫ＞ ALERT TIME "CHG TIP" is displayed on the home screen when the iron tip cumulative running time reaches the set period. To clear this display, you need to change the tip and reset the TIP TIME from the DSP menu. (See ...

  • Page 10: Maintenance

    8. MAINTENANCE Performing proper and periodic maintenance extends product life. Efficient soldering depends upon the temperature, quality and quantity of the solder and flux. Apply the following service procedure as dictated by the conditions of usage. Since the soldering iron can reach a very high temperature, please work carefully. Except the case especially indicated, always turn the power switch OFF and disconnect the power plug before performing any maintenance procedure.

  • Page 11: Parts List

    11. PARTS LIST ● HAKKO FX-100 Starion Item No. Part No. Part Name Specifications Item No. Part No. Part Name Specifications Power cord, 3-wire B5002 P.W.B B2419 120V USA cord & American plug Power cord, 3-wire B5003 Transformer 100 - 110V B2421 cord but no plug Power cord, 3-wire...
  • Page 12 HEAD OFFICE 4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN TEL:+81-6-6561-3225 FAX:+81-6-6561-8466 http://www.hakko.com E-mail:sales@hakko.com OVERSEAS AFFILIATES U.S.A.: AMERICAN HAKKO PRODUCTS, INC. TEL: (661) 294-0090 FAX: (661) 294-0096 Toll Free (800)88-HAKKO 4 2 5 5 6 http://www.hakkousa.com HONG KONG: HAKKO DEVELOPMENT CO., LTD. TEL: 2811-5588 FAX: 2590-0217 http://www.hakko.com.hk E-mail:info@hakko.com.hk...

This manual is also suitable for:

Fx-1001Fx-100Fx-1002

Table of Contents