Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kwikset Rently Smart Bolt Elite Flex
Summary of Contents for Kwikset Rently Smart Bolt Elite Flex
- Page 1 Manufactured by Smart Bolt Elite Flex Installation Manual Rev 1.0...
-
Page 2: Manager Features
NOTE: The battery life is based on 10 entries per day. However, misaligned doors will shorten the battery life since the motor uses more power This manual will walk you through all the required steps to add your new Rently Smart Bolt Elite Flex to your door. -
Page 3: Installation
Installation... -
Page 4: Before Installation
Before Installation WARING: Do not insert the batteries into the lock until it is fully installed. Doing so may damage the lock. Check the parts in the box Exterior Lock Interior Lock Mounting Plate Battery Cover Door Sensor 4 AA Batteries Keys Latch Collar... -
Page 5: Required Tools
Required tools You will need a Phillips head screwdriver. If using an electric screwdriver, we recommend that you adjust it to the lowest torque to avoid stripping the screws Remove your existing deadbolt and strike Installation Instructions Install the Latch... - Page 6 If the rectangle shaped hole is not centered in the door hole, rotate the latch face to extend the latch. If your door is not chiseled, install the drive-in collar.
-
Page 7: Install The Strike
Install the strike... - Page 8 Install the Exterior Lock Arrange the corresponding rubber gaskets to be fully seated against the back of the keypad and the back of the mounting bracket. Feed the keypad wire under the latch, then through the cable hole in the mounting bracket. Route the cable under the latch Make sure the keyhole is in the vertical position and pointing up...
- Page 9 Install the mounting plate and door sensor Route the cable through the bottom hole of the mounting plate Mount the door sensor next to the edge of the door, Route the cable through hole of the rubber pad.
- Page 10 Tighten the screws evenly. DO NOT over-tighten. Install the interior Lock Keep the interior lock knob to pointing up. Connect the keypad cable and the door sensor cable to the interior lock by firmly snapping the connectors together.
- Page 11 WARNING: Adjust the cable under the cable clip to prevent the screws from pinching it. Secure the interior lock onto the mounting plate. Rotate the deadbolt knob by hand to be sure that it moves freely and that the screws are not overtightened.
- Page 12 Install the AA batteries Ensure the door is open while installing batteries. Ensure correct polarity. Use new, non- rechargeable Alkaline batteries only.
-
Page 13: Reference Guide
Reference Guide... - Page 14 Swipe the Fob card close to this Auto Lock switch icon. Enable / Disable Auto Lock feature when a door sensor is 4. Lock button installed. Used for locking the door. Turn piece Smartkey Cylinder Lock and unlock from the Kwikset rekeyable cylinder. interior.
- Page 15 Inclusion / Exclusion / Reset Network On factory default the device does not belong to any Z-Wave® network. The device needs to be added to an existing Z-Wave® network to communicate with the devices of this network. This process is called Inclusion. Devices can also be removed from a Z-Wave®...
-
Page 16: Lock / Unlock The Door
Lock / Unlock the door Locking Unlocking To lock your door, press the To unlock your door, enter the Lock button. The lock will beep User Code, present the User Fob, as the bolt extends. use the physical key or unlock via Rently Smart Home App. -
Page 17: Troubleshooting
SmartKey® Re-key Re-key the lock to work with your existing key by following the SmartKey® Re-key instructions. NOTE: If Auto-Lock is enabled, remove the battery pack before re- keying your lock Troubleshooting If you have any issues, please visit our support center: https://help.rently.com/ Or call us at (855)-248-8144... -
Page 18: Regulatory Compliance
Regulatory Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 19: Technical Specifications
Technical Specifications Dimensions: 6.43’’ x 5’’ x 3.25’’ Protocol: Bluetooth BLE, Z-Wave®, NFC Devices: iOS and Android Compatibility: 1 3/8’’ to 1 3/4’’ door thickness Handing: Self-handing Power: 4 AA Batteries Codes: Supports up to 250 unique codes and 250 Fobs Operating Temp: Exterior: -30˚C to 75˚C Interior: 25˚C to 70˚C...
Need help?
Do you have a question about the Rently Smart Bolt Elite Flex and is the answer not in the manual?
Questions and answers