Kwikset Powerbolt2 User Manual

49697 / 01
Installation Guide
Required Tools
AA
Use and programming
instructions are located on the
Additional Tools (depending on application)
reverse side of this document.
3
Install latch
For doors with chiseled edge For doors without chiseled edge
A
A2
J (2x) B
A
wood
block
7
Load batteries and reset the lock
A B C
Press and hold the
Reset button on the
H
interior assembly for
ve seconds, until you
hear three beeps.
Note: The turnpiece
4x may rotate on its own.
AA
G
Ensure correct polarity. For best
results, use new, non-rechargeable
Alkaline batteries only.
10
Install strike
B
J (2x)
Parts in the Box
Latch and Strike Exterior Assembly Interior Assembly
A B
C
F
If needed, please contact
Kwikset to order a drive-in
D E
latch for your lock.
Fasteners
A2
J
Kwikset
1-800-327-5625
L
www.kwikset.com
4
Prepare exterior keypad (if needed)
For doors with 2-1/8" (54 mm) holes For doors with 1-1/2" (38 mm) holes
2-1/8" 1-1/2"
54 mm 38 mm
Proceed to step 5. Temporarily remove gasket Remove adapter ring
A B
C
C Reinstall gasket,
ensuring a tight seal.
8
Install interior assembly
A B C
G
45°
door
edge
Rotate turnpiece
AWAY from the
door edge.
Align colored edges of
connectors and ensure
secure cable connection.
11
Re-key the lock
D
If needed, re-key the lock to
work with your existing key.
See the supplied SmartKey
Re-key instructions for more
information.
1
Check dimensions
2-3/8" (60 mm)
or
2-3/4" (70 mm) 1-3/8" — 1-3/4"
35 mm — 44 mm
H
1-1/2" 2-1/8"
G
or
38 mm 54 mm
Additional door preparation may be
required for doors with 1-1/2" (38 mm)
holes. Consult the drilling instructions at
www.kwikset.com/doorprep.
K
5
Prepare mounting plate (if needed)
For doors with 2-1/8" (54 mm) holes For doors with 1-1/2" (38 mm) holes
2-1/8"
54 mm
Proceed to step 6.
Use pliers to remove the two tabs from the mounting plate (F).
F
D E
G
K (3x)
Check for smooth turnpiece rotation.
If turnpiece does not rotate, pull
interior assembly (G) off the door.
Repeat steps 7B and 7C, making
sure the turnpiece is rotated
away from the door edge.
12
Program the lock
Programming
instructions are
located on the
reverse side of
this document.
2
Adjust the backset of latch (if needed)
A B
Hold the latch in front of the
door hole, with the latch face
ush against the door edge.
1"
A / A2
25 mm
Latch Adjustment (only if needed)
6
Install keypad and mounting plate
A B
Locate screws (L)
and keep them
1-1/2"
within reach.
38 mm
L
Cable goes
underneath latch
D
Keep parallel to
edge of door
Tighten
screws
evenly
L (2x)
9
IMPORTANT: Enter door handing code and test lock
F
A While the door is OPEN AND UNLOCKED, enter the following code to teach the lock the orientation of the door.
Default
Lock
MASTERCODE:
button
0-0-0-0
B C
Press the Lock If the latch bolt
Make sure
button once. extends to lock,
door is
the lock has
unlocked.
correctly learned
the orientation of
the door.
Template
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available at www.kwikset.com/doorprep.
Edge Face
Fold
Centerline
2-3/8" (60 mm)
2-3/4" (70 mm)
Backset
If the latch holes are
centered in the door hole, no
adjustment is required.
Proceed to step 3.
If the latch holes are NOT
centered, adjust latch. See
"Latch Adjustment."
180°
C
F
C
E
E
Insert key and test latch.
If latch does not extend
or retract smoothly,
adjust screws (L).
L
Remove key when
nished and make sure
the latch bolt is in the
unlocked position.
Lock
If programming is successful,
"0"
button
the keypad will ash green
twice with two beeps.
If unsuccessful, the keypad will
ash red three times with three
beeps. Attempt to enter the
code again.
D
Unlock
door.