1. Manuals
  2. Brands
  3. South bend Manuals
  4. Lathe
  5. SB1114F
  6. Manual

South bend SB1114F Manual

Heavy 13 13" x 30" evs lathe w/dro
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
The Model SB1114F lathe is the same machine as the Model SB1051 except for the following:
•
Model SB1114F requires single-phase, hardwired power supply.
•
Added a 2-Axis Fagor Digital Readout (DRO).
•
The distance between centers is 30".
•
Includes 8 cast iron leveling pads.
Except for the differences noted in this insert, all other content in the Model SB1051 Owner's
Manual applies to this machine. Before operating your new lathe, you MUST read and understand
this insert, the entire Model SB1051 Owner's Manual, and the Fagor DRO Owner's Manual to reduce
the risk of injury when using this machine. Keep this insert for later reference.
If you have any further questions about this manual insert or the differences between the Model
SB1114F and the Model SB1051, contact our Technical Support at (360) 734-1540 or email
sales@southbendlathe.com.
New 2-Axis Fagor DRO
Figure 1. Location of new DRO.
Figure
. Location of new DRO.
Copyright © February, 2021 by South Bend Lathe Co., Revised December, 2021 (CS)
WARNING: No portion of this manual may be reproduced without written approval.
MODEL SB1114F HEAVY 13®
13" X 30" EVS LATHE w/DRO
Manual Insert
PHONE: (360) 734-1540 •
Fagor
Fagor
2-Axis DRO
2-Axis DRO
#CS21577 Printed in Taiwan
www.southbendlathe.com
V2.12.21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SB1114F and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for South bend SB1114F

Summary of Contents for South bend SB1114F

  • Page 1 13" X 30" EVS LATHE w/DRO Manual Insert www.southbendlathe.com PHONE: (360) 734-1540 • The Model SB1114F lathe is the same machine as the Model SB1051 except for the following: • Model SB1114F requires single-phase, hardwired power supply. • Added a 2-Axis Fagor Digital Readout (DRO).

  • Page 2: Product Specifications

    I N T R O D U C T I O N Model SB1114F For Machines Mfd. Since 1/21 Product Specifications Product Specifications P.O. Box 2027, Bellingham, WA 98227 U.S.A. © South Bend Lathe Co. PHONE: (360) 734-1540 • www.southbendlathe.com Model SB1114F 13" x 30" EVS Lathe with DRO Product Dimensions Weight................................

  • Page 3: Main Specifications

    I N T R O D U C T I O N For Machines Mfd. Since 1/21 Model SB1114F Oil Pump Horsepower............................1/4 HP Phase............................Single-Phase Amps................................3A Speed..............................1720 RPM Type............................TEFC Induction Power Transfer ............................Direct Bearings....................Shielded & Permanently Lubricated...
  • Page 4 Approximate Assembly & Setup Time ......................2 Hours Serial Number Location ..........................ID Label Features Allen Bradley Electrical Components Signature South Bend 3 V-Way Bed Safety Chuck Guard with Micro-Switch Shut-Off Halogen Work Light 4-Way Tool Post Complete Recycling Coolant System...

  • Page 5: Power Supply Requirements

    P R E P A R A T I O N For Machines Mfd. Since 1/21 Model SB1114F Power Supply Circuit Information A power supply circuit includes all electrical Requirements equipment between the main breaker box or fuse panel in your building and the incoming power Availability connections inside the machine.

  • Page 6: Power Connection

    P R E P A R A T I O N Model SB1114F For Machines Mfd. Since 1/21 Power Connection Connection Type A permanently connected (hardwired) power supply is typically installed with wires running through mounted and secured conduit. A...
  • Page 7 P R E P A R A T I O N For Machines Mfd. Since 1/21 Model SB1114F Connecting Power Supply Wires to Machine During next step, make sure incoming ground wire is connected to grounding screw to ensure machine will be properly grounded (see "Ground Screw"...

  • Page 8: Correcting Phase Polarity

    P R E P A R A T I O N Model SB1114F For Machines Mfd. Since 1/21 Test Run Correcting Phase Polarity This sub-section is only provided for After all preparation steps have been completed, troubleshooting 3-phase power connections. If...
  • Page 9 P R E P A R A T I O N For Machines Mfd. Since 1/21 Model SB1114F Read and follow the safety instructions at Disengage the quick-change gearbox by the beginning of the SB1051 manual, take moving the feed range lever to the neutral all required safety precautions, and make (middle) position, as shown in Figure 9.
  • Page 10 P R E P A R A T I O N Model SB1114F For Machines Mfd. Since 1/21 12. Start the lathe by pulling the spindle lever Move the spindle speed range lever so the arrow on the hub points to the right (see out (see Figure 11) and moving it down.
  • Page 11 P R E P A R A T I O N For Machines Mfd. Since 1/21 Model SB1114F 17. Move the spindle lever to the OFF (middle) 20. Lift the chuck guard up—this will activate position. Remove the end gear cover from the the chuck guard safety switch.

  • Page 12: Electrical Safety Instructions

    E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine.

  • Page 13: Machine Electrical Overview

    E L E C T R I C A L For Machines Mfd. Since 1/21 Model SB1114F Machine Electrical Overview Page numbers in this Electrical Page numbers in this Electrical section refer to this manual insert, section refer to this manual insert,...

  • Page 14: Electrical Component Location Index

    E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 Electrical Component Location Index Chuck Guard Safety Switch Chuck Guard Safety Switch Work Light Work Light (Page 23) (Page 23) (Page 23) (Page 23) RPM Display &...

  • Page 15: Electrical Cabinet Overview

    E L E C T R I C A L For Machines Mfd. Since 1/21 Model SB1114F Electrical Cabinet Overview Figure Figure 12. Electrical cabinet components and wiring. . Electrical cabinet components and wiring. Circuit Breaker 20A (Page 17) Oil Pump Motor Contactor (Page 17)

  • Page 16: Rpm Display Cabinet Overview

    E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 RPM Display Cabinet Overview RPM Display RPM Display Resistor Resistor Figure Figure 13. RPM cabinet components and wiring. . RPM cabinet components and wiring.

  • Page 17: Upper Electrical Cabinet Wiring Diagram

    E L E C T R I C A L For Machines Mfd. Since 1/21 Model SB1114F Upper Electrical Cabinet Wiring Diagram Electrical Cabinet Electrical Cabinet Terminal Board Terminal Board (Page 18) (Page 18) Circuit Board Circuit Board (Page 19)

  • Page 18: Inverter (N1) & Terminal Board (Tb) Wiring

    E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 Inverter (N1) & Terminal Board (TB) Wiring To Work Light To Work Light (Page 23) (Page 23) To RPM Display To RPM Display...

  • Page 19: Circuit Board (Pcb) Wiring Diagram

    E L E C T R I C A L For Machines Mfd. Since 1/21 Model SB1114F Circuit Board (PCB) Wiring Diagram SPINDLE ROTATION To Inverter To Inverter (Page 18) (Page 18) To Control To Control Panel (Page 20) Panel (Page 20)

  • Page 20: Control Panel Overview

    E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 Control Panel Overview Spindle Speed Spindle Speed Power Power Coolant Pump Coolant Pump STOP STOP Dial Dial Light Light Switch Switch Button Button...

  • Page 21: Spindle Motor Wiring

    CUTTING FLUID E L E C T R I C A L PUMP MOTOR For Machines Mfd. Since 1/21 Model SB1114F (440V) Spindle Motor Wiring Ground Figure Figure 15. Spindle motor junction box. Spindle motor junction box. To Electrical Cabinet Terminal Board...
  • Page 22 E L E C T R I C A L Model SB1114F For Machines Mfd. Since 1/21 Spindle Switch Wiring To Electrical To Electrical Cabinet Cabinet Terminal Board Terminal Board (Page 18) (Page 18) Figure Figure 17. Spindle switch wiring.
  • Page 23 E L E C T R I C A L For Machines Mfd. Since 1/21 Model SB1114F Additional Component Wiring RPM Sensor RPM Sensor RPM Sensor Work Light End Gear End Gear Cover Safety Cover Safety Chuck Guard Switch Switch...

  • Page 24: Headstock Cover

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Headstock Cover PARTS REF PART # DESCRIPTION REF PART # DESCRIPTION PSB1114F0001 OIL FILL CAP 3/4" PSB1114F0003 HEADSTOCK COVER PSB1114F0002 CAP SCREW M6-1 X 40 PSB1114F0004 TOP COVER GASKET...

  • Page 25: Headstock Controls

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Headstock Controls 160-2 160-3 160-1 160-4 160-5 160-6 -25-...
  • Page 26 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Headstock Controls Parts List REF PART # DESCRIPTION PART # DESCRIPTION PSB1114F0006 FLAT WASHER 10MM PSB1114F0049 CAP SCREW M5-.8 X 15 PSB1114F0007 FEED DIRECTION SHIFT FORK PSB1114F0050 SHIFT LEVER...

  • Page 27: Headstock Internal Gears

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Headstock Internal Gears -27-...
  • Page 28 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Headstock Internal Gears Parts List REF PART # DESCRIPTION PART # DESCRIPTION PSB1114F0038 CAP SCREW M6-1 X 16 PSB1114F0095 INT RETAINING RING 62MM PSB1114F0061 OIL SEAL 60 X 62 X 12MM...

  • Page 29: Headstock Transfer Gears

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Headstock Transfer Gears 126 38 PART # DESCRIPTION PART # DESCRIPTION PSB1114F0010 CAP SCREW M6-1 X 10 PSB1114F0131 SHAFT PSB1114F0024 O-RING 43.7 X 3.5 P44 PSB1114F0132 FLAT WASHER 3/4 PSB1114F0030 SET SCREW M8-1.25 X 8...

  • Page 30: Gearbox Gears

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Gearbox Gears 226 225 -30-...
  • Page 31 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Gearbox Gears Parts List PART # DESCRIPTION PART # DESCRIPTION PSB1114F0201 SPLINED SHAFT PSB1114F0232 GEAR 19T PSB1114F0202 OIL SEAL 20 X 32 X 5MM PSB1114F0233 GEAR 20T PSB1114F0203...

  • Page 32: Gearbox Controls

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Gearbox Controls -32-...
  • Page 33 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Gearbox Controls Parts List PART # DESCRIPTION PART # DESCRIPTION PSB1114F0262 FRONT COVER GASKET PSB1114F0301 WOODRUFF KEY 4 X 13MM PSB1114F0263 JACK SCREW PSB1114F0302 SHIFT SHAFT PSB1114F0264 BINDING PLATE PSB1114F0303 O-RING 17.8 X 2.4 P18...
  • Page 34 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Apron -34-...

  • Page 35: Apron Parts List

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Apron Parts List PART # DESCRIPTION PART # DESCRIPTION PSB1114F0501 COMBO GEAR 18T/60T PSB1114F0550 APRON FRONT PANEL PSB1114F0502 THRUST WASHER AS3047 PSB1114F0551 BEVEL GEAR SHAFT 23T PSB1114F0503 ROLL PIN 4 X 22...

  • Page 36: Compound Rest & Tool Post

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Compound Rest & Tool Post 715A -36-...
  • Page 37 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Compound Rest & Tool Post Parts List PART # DESCRIPTION PART # DESCRIPTION PSB1114F0701 TOOL POST NUT FIXED HANDLE PSB1114F0717 INDICATOR PLATE PSB1114F0702 TOOL POST NUT PSB1114F0718 LEADSCREW BRACKET...

  • Page 38: Saddle Top View

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Saddle Top View 813A 910 906 906 821 -38-...
  • Page 39 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Saddle Top View Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION PSB1114F0801 GIB ADJUSTMENT SCREW PSB1114F0829 COMPRESSION SPRING 6 X 15 802 PSB1114F0802 CROSS SLIDE 830 PSB1114F0830 THRUST BEARING NTB/AS2 1730...

  • Page 40: Saddle Bottom View

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Saddle Bottom View (Viewed from underneath the saddle) REF PART # DESCRIPTION REF PART # DESCRIPTION PSB1114F0841 SPACER 6.5 X 15 X 3 PSB1114F0849 OIL TUBE 6 X 160MM ALUMINUM...

  • Page 41: Micrometer Stop

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Micrometer Stop Dial Indicator 1051 1000 1050 1061 1001 1004 1062 1002 1003 1005 1063 1009 1006 1052 1065 1064 1010 1007 1011 1067 1066 1012 1053 1068...

  • Page 42: Bed & Shafts

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Bed & Shafts 1163-2 1163 1163-3 1163-5 1103 1163-4 1163-1 1104 1101 1163-6 1150 1146 1145 1102 1144 1143 1142 1141 1148 1140 1139 1149 1147 1140 1137...
  • Page 43 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Bed & Shafts Parts List PART # DESCRIPTION PART # DESCRIPTION 1101 PSB1114F1101 BED W/GAP 30" 1136 PSB1114F1136 CLUTCH COLLAR 1102 PSB1114F1102 CARRIAGE STOP BOLT 1137 PSB1114F1137 TAPERED BUSHING...

  • Page 44: End Gears

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 End Gears 1205 1204 1214 1203 1202 1201 1213 1209 1208 1210 1208 1215 1206 1207 1212 1211 1207 1210 1207 1206 1206 1219 1216 1217 1218 PART #...

  • Page 45: Main Motor

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Main Motor 1303 1349-1 1305 1349-2 1304 1349-3 1349-4 1349-5 1349 1322 1323 1314 1324 1321 1320 1328 1319 1318 1305 1330 1317 1331 1327 1315 1326 1330...
  • Page 46 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Main Motor Parts List PART # DESCRIPTION PART # DESCRIPTION 1301 PSB1114F1301 END GEAR COVER 1325 PSB1114F1325 TAPER PIN #4 X 1-3/4" 1302 PSB1114F1302 KNOB M10-1.5 ROUND KN...

  • Page 47: Stands & Panels

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Stands & Panels 1446 1436 1433 1435 1432 1445 1421 1405 1424 1437 1425 1423 1434 1426 1427 1422 1420 1428 1438 1429 1431 1430 1418 1429 1419...
  • Page 48 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Stands & Panels Parts List PART # DESCRIPTION PART # DESCRIPTION 1401 PSB1114F1401 BRAKE PEDAL ROD 1427 PSB1114F1427 PHLP HD SCR M4-.7 X 40 1402 PSB1114F1402 BRAKE PEDAL...

  • Page 49: Headstock Lubrication System

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Headstock Lubrication System 1536 1539 1537 1529 1535 1504 1537 1506 1538 1534 1514 1537 1536 1515 1535 1530 1534 1505 1506 1531 1504 1507 1501 1502 1532...
  • Page 50 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Headstock Lubrication System Parts List REF PART # DESCRIPTION PART # DESCRIPTION 1501 PSB1114F1501 OIL TUBE ELBOW ADAPTER 3/8" PT X M16-2 1524 PSB1114F1524 LUBRICATION PUMP AM6 1502 PSB1114F1502 OIL TUBE SEAL PB10...
  • Page 51 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Tailstock 1603 1701 1604 1606 1601 1607 1604 1608 1609 1605 1614 1610 1613 1642 1643 1702 1644 1620 1617 1641 1619 1622 1618 1612 1621 1624 1611...

  • Page 52: Tailstock Parts List

    P A R T S Model SB1114F For Machines Mfd. Since 1/21 Tailstock Parts List PART # DESCRIPTION PART # DESCRIPTION 1601 PSB1114F1601 TAILSTOCK LEADSCREW 1632 PSB1114F1632 V-WAY WIPER 1602 PSB1114F1602 TAILSTOCK LEADSCREW NUT 1633 PSB1114F1633 V-WAY WIPER PLATE 1603...

  • Page 53: Steady Rest

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Steady Rest Follow Rest 1801 1802 1851 1803 1800 1853 1852 1804 1806 1805 1854 1809 1807 1810 1808 1855 1850 1856 1812 1811 1857 1858 1813 1815...
  • Page 54 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Bed Stop Chip Cover 1954 1901 1952 1953 1951 1902 1906 1907 1903 1904 1951 1957 1905 1956 1955 PART # DESCRIPTION PART # DESCRIPTION 1901 PSB1114F1901 CAP SCREW M10-1.5 X 60...

  • Page 55: Electrical Cabinets & Control Panel

    P A R T S For Machines Mfd. Since 1/21 Model SB1114F Electrical Cabinets & Control Panel 2025 2001 2002 2027 2026 2004 2007V2 2009 2024 2007V2 2006 2010 2005 2008 2010 2015 2016 2005-1 2006-1 2015 2015 2014 2003...
  • Page 56 P A R T S Model SB1114F For Machines Mfd. Since 1/21 Electrical Cabinets & Control Panel Parts List PART # DESCRIPTION REF PART # DESCRIPTION 2001 PSB1114F2001 RPM DISPLAY NEWCAL SPP-1406 2014 PSB1114F2014 CIRCUIT BOARD SC-001-1 2002 PSB1114F2002 RESISTOR 800W 20OHM...
  • Page 57 P A R T S For Machines Mfd. Since 1/21 Model SB1114F Accessories 2103-1 2104 2105 2102 2103-2 2101 2118 2117 2116 2106 2103 2107 2109 2108 2110 2111 2114 2112 2113 2115 PART # DESCRIPTION REF PART # DESCRIPTION...

  • Page 58: Front Machine Labels

    The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

  • Page 59: Rear & Side Machine Labels

    READ MANUAL LABEL 2212 PSB1114F2212 SAFETY GLASSES LABEL 2202 PSB1114F2202 CHANGING END GEARS LABEL 2213 PSB1114F2213 SOUTH BEND NAMEPLATE 203MM 2203 PSB1114F2203 CHANGING SPEEDS NOTICE LABEL 2214 PSB1114F2214 CHUCK KEY WARNING LABEL 2204 PSB1114F2204 SPINDLE SPEED WARNING LABEL 2215 PSB1114F2215...
  • Page 60 Printed In Taiwan #CS21577...
  • Page 61 ® 13" X 40" HEAVY 13 EVS LATHE MODEL SB1051 OWNER'S MANUAL © March, 2012 by South Bend Lathe Co., Revised December, 2012 (TS) For Machines Mfg. Since 5/11...

  • Page 62: Scope Of Manual

    What did you like about it? Is there anything you would change to make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use? South Bend Lathe, Inc. / / Technical Documentation Manager P.O. Box 2027 Bellingham, WA 98227 Email: manuals@southbendlathe.com...

  • Page 63: Table Of Contents

    Table of Contents INTRODUCTION ............3 Test Run ............. 25 Spindle Break-In ..........28 About This Machine ..........3 ............. 3 Recommended Adjustments ......29 Foreword ............3 Capabilities OPERATION ............30 .............. 3 Features Operation Overview ........... 30 General Identification .......... 4 Chuck &...
  • Page 64 .......... 50 ELECTRICAL ............86 Power Feed Controls ........51 Electrical Safety Instructions ......86 Setting Power Feed Rate End Gears ............52 Machine Electrical Overview ......87 ...... 52 Electrical Component Location Index ....88 Standard End Gear Configuration ........53 Electrical Cabinet Overview ......

  • Page 65: Introduction

    As the operator of a South Bend Lathe, you now join the ranks of some very famous and important customers, such as Henry Ford, who used the machines he purchased to help him change the world.

  • Page 66: General Identification

    13" x 40" Heavy 13 ® EVS Lathe I N T R O D U C T I O N For Machines Mfg. Since 5/11 General Identification Figure 1. Identification. A. Spindle Speed Digital Readout Coolant Pump & Tank Access B.

  • Page 67: Basic Controls

    I N T R O D U C T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Headstock & Quick-Change Basic Controls Gearbox Refer to Figures 2–7 and the following descriptions to become familiar with the basic controls of this lathe.

  • Page 68: Control Panel

    13" x 40" Heavy 13 ® EVS Lathe I N T R O D U C T I O N For Machines Mfg. Since 5/11 4-Way Tool Post: Mounts up to four cutting Control Panel tools at once that can be individually indexed to the workpiece.

  • Page 69: Tailstock

    I N T R O D U C T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Tailstock Safety Brake Pedal This lathe is equipped with a brake pedal (see Figure 7) to quickly stop the spindle instead of allowing it to coast to a stop on its own.

  • Page 70: Product Specifications

    13" x 40" Heavy 13 ® EVS Lathe I N T R O D U C T I O N For Machines Mfg. Since 5/11 Product Specifications 0RGHO 6% +HDY\   [  (96 /DWKH Š 2TQFWEV &KOGPUKQPU 9GKIJV  NDU 9KFVJ UKFGVQUKFG Z &GRVJ HTQPVVQDCEM Z *GKIJV  Z  Z  KP (QQVRTKPV .GPIVJ Z 9KFVJ   Z  KP 5JKRRKPI &KOGPUKQPU...
  • Page 71 I N T R O D U C T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe %QQNCPV 2WOR 6[RG 6'(% +PFWEVKQP %NCUU ( *QTUGRQYGT  *2 2JCUG 2JCUG #ORU # 5RGGF  42/ 2QYGT 6TCPUHGT  &KTGEV &TKXG $GCTKPIU 5JKGNFGF 2GTOCPGPVN[ .WDTKECVGF...
  • Page 72 13" x 40" Heavy 13 ® EVS Lathe I N T R O D U C T I O N For Machines Mfg. Since 5/11 &KOGPUKQPU $GF 9KFVJ  KP .GCFUETGY &KCOGVGT  KP .GCFUETGY 62+  62+ .GCFUETGY .GPIVJ  KP 5VGCF[ 4GUV %CRCEKV[   KP (QNNQY 4GUV %CRCEKV[ ...

  • Page 73: Safety

    S A F E T Y For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).
  • Page 74 13" x 40" Heavy 13 ® EVS Lathe S A F E T Y For Machines Mfg. Since 5/11 Entanglement: Loose clothing, gloves, neckties, Chuck Keys or Adjusting Tools: Tools used to jewelry or long hair may get caught in adjust spindles, chucks, or any moving/ moving parts, causing entanglement, rotating parts will become dangerous...

  • Page 75: Additional Metal Lathe Safety

    S A F E T Y For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Additional Metal Lathe Safety Speed Rates. Operating the lathe at the wrong Clearing Chips. Metal chips can easily cut bare speed can cause nearby parts to break or the skin—even through a piece of cloth.

  • Page 76: Additional Chuck Safety

    13" x 40" Heavy 13 ® EVS Lathe S A F E T Y For Machines Mfg. Since 5/11 Additional Chuck Safety Entanglement. Entanglement with a rotating Chuck Capacity. Avoid exceeding the capacity chuck can lead to death, amputation, broken of the chuck by clamping an oversized bones, or other serious injury.

  • Page 77: Preparation

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Preparation Overview Things You'll Need The purpose of the preparation section is to help To complete the preparation process, you will you prepare your machine for operation.

  • Page 78: Power Supply Requirements

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 The full-load current is not the maximum Power Supply amount of amps that the machine will draw. If the machine is overloaded, it will draw additional Requirements amps beyond the full-load rating.

  • Page 79: Grounding Requirements

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Grounding Requirements Extension Cords This machine must be grounded! In the event We do not recommend using an extension cord of certain types of malfunctions or breakdowns, with this machine.

  • Page 80: Unpacking

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 Unpacking This item was carefully packaged to prevent damage during transport. If you discover any damage, please immediately call Customer Service at (360) 734-1540 for advice.

  • Page 81: Cleaning & Protecting

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Cleaning & Protecting Avoid chlorine-based solvents, such as The unpainted surfaces are coated at the factory acetone or brake parts cleaner that may with a heavy-duty rust preventative that damage painted surfaces.

  • Page 82: Location

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 Weight Load Location Location Refer to the Machine Specifications for the Physical Environment weight of your machine. Make sure that the surface upon which the machine is placed will The physical environment where your machine bear the weight of the machine, additional...

  • Page 83: Lifting & Moving

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Position hardwood blocking under each Lifting & Moving end of the bed, as shown in Figure 12. This will keep the lifting straps away from the leadscrew, feed rod, and spindle rod to prevent bending them during lifting.

  • Page 84: Leveling & Mounting

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 Attach the lifting straps to the power lifting Leveling & Mounting equipment (see Figure 14 for an example). You must level your machine and either use Power Lifting the included foot pads and leveling hardware or...

  • Page 85: Bolting To Concrete Floors

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe To level the machine, use a precision level to Assembly make sure the bedways are level from side-to- side and from front-to-back.

  • Page 86: Adding Coolant

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 Besides adding oil to the reservoirs, we also To connect power cord to the lathe: recommend that you lubricate other points on MAKE SURE POWER CORD IS NOT YET the lathe at this time.

  • Page 87: Test Run

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Connect the incoming ground wire to the Test Run ground terminal directly above the master power switch, as illustrated in Figure 20. After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation.
  • Page 88 13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 Clear away all tools and objects used during Note: During the next step, you may need to use assembly, lubrication, and preparation.
  • Page 89 P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe 11. To ensure carriage components do not 14. Press the STOP button to turn the lathe unexpectedly move during the following OFF, then, without resetting the STOP steps, disengage the half nut lever and feed...

  • Page 90: Spindle Break-In

    13" x 40" Heavy 13 ® EVS Lathe P R E P A R A T I O N For Machines Mfg. Since 5/11 19. Push the STOP button in, move the spindle Spindle Break-In lever to the OFF position, then replace the end gear cover.

  • Page 91: Recommended Adjustments

    P R E P A R A T I O N For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Use the foot brake to stop spindle rotation, Recommended then run the lathe at 250 RPM for 10 minutes with the feed range lever on the Adjustments headstock in the L (low) position, and then...

  • Page 92: Operation

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 To complete a typical operation, the operator Operation Overview does the following: The purpose of this overview is to provide Puts on safety glasses, rolls up sleeves, the novice machine operator with a basic removes jewelry, and secures any clothing,...

  • Page 93: Chuck & Faceplate Mounting

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Chuck & Faceplate Installation & Removal Mounting Devices This lathe is equipped with a D1-type spindle Because chucks are heavy and often awkward to nose.

  • Page 94: Chuck Installation

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Incrementally tighten the camlocks in a Chuck Installation criss-cross or star pattern to ensure that the To ensure accurate work, it is extremely chuck seats evenly against the spindle.

  • Page 95: Registration Marks

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Verify that the chuck fits the spindle Chuck Removal properly by checking for any gaps between the mating surfaces. To remove the chuck: DISCONNECT LATHE FROM POWER! —...

  • Page 96: Scroll Chuck Clamping

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Scroll Chuck Clamping 4-Jaw Chuck This scroll-type chuck has an internal scroll-gear Refer to the Chuck Installation (see Page 32) that moves all jaws in unison when adjusted with and Chuck Removal (see Page 33) instructions the chuck key.

  • Page 97: Faceplate

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Tighten each jaw in small increments. Faceplate After you have adjusted the first jaw, continue tightening the remaining jaws Refer to the Chuck Installation (see Page 32) in an opposing sequence, as shown by the and Chuck Removal (see Page 33) instructions...

  • Page 98: Tailstock

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 To mount a non-concentric workpiece to the Quill Lock Tailstock Lock faceplate: Lever Lever DISCONNECT LATHE FROM POWER! Protect the bedway with a piece of plywood.

  • Page 99: Installing Tooling

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe However, other tooling without tangs, such as Installing Tooling the four remaining tools shown in Figure 37, This tailstock uses a quill with an MT#5 taper can still be used if the potential load will not that has a lock slot in the back of the bore that exceed the strength of the tapered fit.

  • Page 100: Removing Tooling

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 To offset the tailstock: Removing Tooling Loosen the hex bolts underneath both ends Use a shop rag to hold the tool. of the tailstock to release the clamping pressure between the top and bottom Rotate the quill handwheel counterclockwise...

  • Page 101: Aligning Tailstock To Spindle Centerline

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Note: As long as this dead center remains in the Aligning Tailstock to Spindle chuck, the point of the center will remain Centerline true to the spindle centerline.

  • Page 102: Centers

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Note: If necessary in the following step, refer Centers to Offsetting Tailstock on Page 38 for detailed instructions. Figure 46 shows the MT#5 dead centers included with the lathe.

  • Page 103: Live Centers

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Live Centers Removing Center from Spindle A live center has bearings that allow the center To remove the sleeve and center from the tip and the workpiece to rotate together;...

  • Page 104: Removing Center From Tailstock

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Use the quill handwheel to feed the quill out Mounting Workpiece Between from the casting approximately 1". Centers Note: Do not extend the quill more than 2"...

  • Page 105: Steady Rest

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Loosen the clamp knob that secures the two Steady Rest halves of the steady rest and open the top portion, as shown in Figure 52.

  • Page 106: Follow Rest

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Follow Rest Carriage & Slide Locks The follow rest mounts to the saddle with two The carriage, cross slide, and compound rest cap screws (see Figure 53).

  • Page 107: Compound Rest

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Compound Rest Four-Way Tool Post The compound rest handwheel has an indirect- The four-way tool post is mounted on top of the read graduated scale.

  • Page 108: Aligning Cutting Tool With Spindle Centerline

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Tools Needed Aligning Cutting Tool with Spindle Tool Post T-Wrench ..........1 Centerline Steel Shims ..........As Needed For most operations, the cutting tool tip should Cutting Tool ............

  • Page 109: Adjustable Feed Stop

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Adjustable Feed Stop Micrometer Stop The adjustable feed stop collar shown in Figure 60, The micrometer stop allows you to manually is designed to stop carriage movement when using stop the carriage at the same position for repeat the feed rod.

  • Page 110: Manual Feed

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Manual Feed Spindle Speed The handwheels shown in Figure 62 allow the Using the correct spindle speed is important operator to manually move the cutting tool.

  • Page 111: Setting Spindle Speed

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Rotate the spindle speed dial on the control Setting Spindle Speed panel all the way counterclockwise to set it Setting the spindle speed requires positioning at the minimum speed for startup.

  • Page 112: Power Feed Controls

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 A. Feed Range Lever: Selects the low or high feed rate range by re-aligning the headstock transfer gear. In the middle position, ALWAYS make sure the spindle is completely disables power feed.

  • Page 113: Setting Power Feed Rate

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Setting Power Feed Rate The feed rate chart on the upper right of the headstock face shows the settings for metric and inch feed rates.

  • Page 114: End Gears

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 End Gears When using power feed to move the cross The end gears can be setup for the standard or slide, the feed rate is ⁄...

  • Page 115: Alternate Configuration

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Loosen the pivot hex nut shown in Figure Alternate Configuration 72, then swing the pivot arm to the left so Use the alternate end gear configuration for that 44T/56T gears are away from the 57T cutting modular or diametral threads.

  • Page 116: Threading

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 The configuration string of characters to Threading the right of the selected thread pitch (LS8Y) displays the positions to set the threading The following subsections describe how to use controls for a metric thread pitch of 1.75 (see the threading controls and charts to set up...

  • Page 117: Apron Threading Controls

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe Apron Threading Controls Thread Dial The half nut lever (see Figure 74) engages the When inch threading, the numbers on the thread carriage with the leadscrew, which moves the dial are used with the thread dial chart to show carriage and cutting tool along the length of the...

  • Page 118: Thread Dial Chart

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Even TPI Not Divisible By 4 Thread Dial Chart For threading a TPI that is even but not divisible The thread dial chart (see Figure 76) can be by 4, use any of the non-numbered lines on the found on the front of the thread dial housing.

  • Page 119: Chip Drawer

    For Machines Mfg. Since 5/11 O P E R A T I O N 13" x 40" Heavy 13 ® EVS Lathe ⁄ ⁄ Fractional TPI Chip Drawer For TPI that have a ⁄ ⁄ fraction, use position The chip drawer catches swarf and metal 1 on the thread dial (see Figure 81).

  • Page 120: Coolant System

    13" x 40" Heavy 13 ® EVS Lathe O P E R A T I O N For Machines Mfg. Since 5/11 Coolant System When the coolant pump is turned ON and the BIOLOGICAL & POISON valve lever (see Figure 84) is opened, fluid is HAZARD! delivered through the nozzle from the coolant Use the correct personal...

  • Page 121: Accessories

    This collet attachment takes advantage of the setting tapers. South Bend factory-made collet port in the lathe gear cover. It installs easily without requiring modification to the gear cover. Capable of delivering years of trouble-free service and...
  • Page 122 Pictures just don't do them justice. They are very nice quality clocks and perfect for the South Bend Lathe aficionado. 6.14" 2.05" 3.39" 0.71" SB1298 SB1299 3.07" 0.59" 70° SB1300 Figure 91. Antique-finished South Bend shop clocks. Figure 93. SB1246 MT#3 Bull Nose Center. -60-...
  • Page 123 SB1365—Way Oil SB1251—Machinist's Oak Tool Box Engineered for the high pressure exerted on Proudly made in the South Bend tradition, this horizontal or vertical ways and slides. Protects heavy-duty oak tool chest will safeguard your against rust and corrosion. Ensures stick-free, finest tools for many years of dependable service.

  • Page 124: Maintenance

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 Daily, After Operations Maintenance Schedule • Depress STOP button and shut OFF the master power switch (to prevent accidental startup).

  • Page 125: Maintenance Chart

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe -63-...

  • Page 126: Lubrication

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 Lubrication Oil Fill The following recommended lubrication Spout schedules are based on light-to-medium usage. Keeping in mind that lubrication Headstock helps to protect the value and operation Oil Tank...

  • Page 127: Changing Headstock Oil

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Remove the side and rear motor access Verifying Oil Pump Operation covers and the end gear cover. To prevent costly damage to the headstock gears and bearings, a kill switch will shut the Remove the three V-belts (refer to V-Belts...

  • Page 128: Quick-Change Gearbox

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 Remove the oil fill spout cover, place the Tip: Place one or more magnets at the bottom of catch pan under the oil tank drain plug (see the tank to collect any fine metal particles.

  • Page 129: Adding Oil

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Adding Oil Draining Oil & Flushing Reservoir Use a 12mm wrench to remove the gearbox fill Since the apron oil reservoir supplies the one- plug (see Figure 103).

  • Page 130: One-Shot Oiler

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 One-Shot Oiler Longitudinal Leadscrew The one-shot oiler shown in Figure 107 Oil Type ..Mobil Vactra 2 or ISO 68 Equivalent lubricates the saddle ways with oil from the Oil Amount ..........

  • Page 131: Ball Oilers & Oil Cup

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe A. Cross Slide Leadscrew & Nut Ball Oilers & Oil Cup B. Compound Rest Leadscrew & Nut Oil Type ..

  • Page 132: End Gears

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 End Gears Lubricating DISCONNECT LATHE FROM POWER! Grease Type ..........NLGI#2 Frequency ....Annually or When Changing Remove the end gear cover and all the end gears shown in Figure 111.

  • Page 133: Coolant System Service

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Although most swarf from machining operations Coolant System is screened out of the coolant before it returns to the tank, small particles will accumulate in Service the bottom of the tank in the form of sludge.

  • Page 134: Adding Fluid

    13" x 40" Heavy 13 ® EVS Lathe M A I N T E N A N C E For Machines Mfg. Since 5/11 To change the coolant: Adding Fluid Position the coolant nozzle over the back of DISCONNECT LATHE FROM POWER! the backsplash so that it is pointing behind the lathe.

  • Page 135: Machine Storage

    M A I N T E N A N C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Slide the tank partially into the base and re- Thoroughly clean all unpainted, bare metal connect the fluid hose. surfaces, then apply a liberal coat of way oil, heavy grease, or rust preventative.

  • Page 136: Backlash Adjustment

    13" x 40" Heavy 13 ® EVS Lathe S E R V I C E For Machines Mfg. Since 5/11 Cross Slide Backlash Adjustment Tools Needed: Backlash is the amount of free play felt while Hex Wrench 3mm ..........1 changing rotation directions with the handwheel.

  • Page 137: Leadscrew End Play Adjustment

    S E R V I C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Leadscrew End Play Gib Adjustment The goal of adjusting the gib screws is to remove Adjustment sloppiness or "play" from the ways without over- adjusting them to the point where they become After a long period of time, you may find that stiff and difficult to move.
  • Page 138 13" x 40" Heavy 13 ® EVS Lathe S E R V I C E For Machines Mfg. Since 5/11 Figures 118–122 show the location of the Note: Remove the thread dial body and the adjustment screws for each gib on this machine. carriage lock clamp to access the saddle gib adjustment screw on the tailstock side (see Figure 121).

  • Page 139: Half Nut Adjustment

    S E R V I C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Half Nut Adjustment V-Belts The clamping pressure of the half nut is fully V-belts stretch and wear with use, so check the adjustable with a gib that can be loosened or tension on a monthly basis to ensure optimal tightened by two set screws.

  • Page 140: Brake & Switch

    13" x 40" Heavy 13 ® EVS Lathe S E R V I C E For Machines Mfg. Since 5/11 Remove the pedal stop shown in Figure 127. Brake & Switch As the brake lining wears, the foot pedal Pedal Lever develops more travel.

  • Page 141: Leadscrew Shear Pin Replacement

    Contact South Bend to order a replacement shear pin (Part Number PSB10121234) or use the Pedal specifications in Figure 130 to fabricate your own.
  • Page 142 13" x 40" Heavy 13 ® EVS Lathe S E R V I C E For Machines Mfg. Since 5/11 To replace the shear pin: Use the magnet to remove the shear pin head, then rotate the lathe spindle to line DISCONNECT LATHE FROM POWER! up the inner and outer bores, as shown in Figure 133.

  • Page 143: Gap Insert Removal & Installation

    S E R V I C E For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe With the pin completely seated in the bore Gap Insert Removal & and the head flush with the leadscrew shoulder, slide the shroud washer against Installation the shoulder, then rotate the washer 180°...

  • Page 144: Gap Removal

    13" x 40" Heavy 13 ® EVS Lathe S E R V I C E For Machines Mfg. Since 5/11 Install all fasteners and lightly snug them in Gap Removal place. Remove the four gap-bed cap screws, shown in Figure 138. Mount a dial indicator with a magnetic base to the top of the saddle to indicate alignment.

  • Page 145: Troubleshooting

    TROU B LESHOOTI NG For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. Symptom Possible Cause Possible Solution...
  • Page 146 13" x 40" Heavy 13 ® EVS Lathe TROU B LESHOOTI NG For Machines Mfg. Since 5/11 Symptom Possible Cause Possible Solution Entire machine 1. Workpiece is unbalanced. 1. Re-install workpiece as centered with the spindle bore as possible. vibrates upon startup and while 2.
  • Page 147 TROU B LESHOOTI NG For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Symptom Possible Cause Possible Solution Workpiece is 1. Headstock and tailstock are not 1. Realign the tailstock to the headstock spindle bore properly aligned with each other. centerline (see Page 39).

  • Page 148: Electrical

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines.

  • Page 149: Machine Electrical Overview

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Machine Electrical Overview RPM Display (Page 90) Chuck Guard Safety Switch (Page 97) Resistor (Page 90) Work Light (Page 97) Electrical Cabinet (Pages 91, 93, &...

  • Page 150: Electrical Component Location Index

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 Electrical Component Location Index Chuck Guard Safety Switch Work Light (Page 97) (Page 97) RPM Display & Resistor (Page 90) Control Panel (Page 94)

  • Page 151: Electrical Cabinet Overview

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Electrical Cabinet Overview Figure 139. Electrical cabinet components and wiring. Circuit Breaker 24V (Page 91) Oil Pump Motor Contactor (Page 91) Spindle Motor Overload Relay (Page 91) Inverter (Page 92) Oil Pump Motor Overload Relay (Page 91)

  • Page 152: Rpm Display Cabinet Overview

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 RPM Display Cabinet Overview RPM Display Resistor Figure 140. RPM cabinet components and wiring. RPM Display Cabinet Wiring Diagram (RPM &...

  • Page 153: Upper Electrical Cabinet Wiring Diagram

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Upper Electrical Cabinet Wiring Diagram 220 380 400 415 440 Transformer Ciruit Breakers Grnd Ground R/L1 S/L2 T/L3 Ground Spindle Contactor...

  • Page 154: Inverter (N1) & Terminal Board (Tb) Wiring

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 Inverter (N1) & Terminal Board (TB) Wiring To RPM Display To Work Light Cabinet Wiring (Page 97) (Page 90 ) Inverter To Chuck...

  • Page 155: Circuit Board (Pcb) Wiring Diagram

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Circuit Board (PCB) Wiring Diagram To Inverter (Page 92) To Control Panel (Page 94) VR4 3 Control Panel VR4 2 Control Panel VR4 1...

  • Page 156: Control Panel Overview

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 Control Panel Overview Spindle Speed Power Coolant Pump STOP Dial Light Switch Button Button Figure 141. Control panel wiring (viewed from behind). Control Panel Wiring Diagram Spindle Speed Power Light...

  • Page 157: Spindle Motor Wiring

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Spindle Motor Wiring Junction Ground Figure 142. Spindle motor junction box. To Electrical Cabinet Terminal Board (Page 92) Coolant Pump Motor Wiring To Electrical Cabinet Terminal Board (Page 92)

  • Page 158: Spindle Switch Wiring

    13" x 40" Heavy 13 ® EVS Lathe E L E C T R I C A L For Machines Mfg. Since 5/11 Spindle Switch Wiring To Electrical Cabinet Terminal Board (Page 92) Figure 144. Spindle switch wiring. Oil Pump Motor & Pressure Sensor Wiring To Electrical Cabinet Oil Pressure Terminal Board...

  • Page 159: Additional Component Wiring

    E L E C T R I C A L For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Additional Component Wiring RPM Sensor Work Light End Gear Cover Safety Chuck Guard Switch Safety Switch Figure 146. End gear cover safety switch and RPM sensor.

  • Page 160: Parts

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Headstock Cover PART # DESCRIPTION PART # DESCRIPTION PSB10510001 OIL CAP PSB10510003 HEADSTOCK TOP COVER PCAP29M CAP SCREW M6-1 X 40 PSB10510004 TOP COVER GASKET -98-...

  • Page 161: Headstock Controls

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Headstock Controls -99-...
  • Page 162 13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Headstock Controls Parts List PART # DESCRIPTION PART # DESCRIPTION PW04M FLAT WASHER 10MM PSB10510048 SHIFT LEVER BRACKET PSB10510007 FEED DIRECTION SHIFT FORK PCAP24M CAP SCREW M5-.8 X 16 PEC015M...

  • Page 163: Headstock Internal Gears

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Headstock Internal Gears -101-...
  • Page 164 13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Headstock Internal Gears Parts List PART # DESCRIPTION PART # DESCRIPTION PCAP01M CAP SCREW M6-1 X 16 PR38M INT RETAINING RING 62MM PSB10510061 OIL SEAL 30 X 62 X 12MM PSB10510096...

  • Page 165: Headstock Transfer Gears

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Headstock Transfer Gears PART # DESCRIPTION PART # DESCRIPTION PORP044 O-RING 43.7 X 3.5 P44 PSB10510132 SHAFT FLAT WASHER 6MM PSS20M SET SCREW M8-1.25 X 8 PSB10510133 COMBO GEAR ASSY 21T/42T PRIV009M...

  • Page 166: Gearbox Gears

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Gearbox Gears -104-...
  • Page 167 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Gearbox Gears Parts List PART # DESCRIPTION PART # DESCRIPTION PSB10510201 SPLINE SHAFT PSB10510232 GEAR 19T PSB10510202 OIL SEAL 20 X 32 X 5 PSB10510233 GEAR 20T PSB10390203...

  • Page 168: Gearbox Controls

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Gearbox Controls -106-...
  • Page 169 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Gearbox Controls Parts List PART # DESCRIPTION PART # DESCRIPTION PSB10510262 FRONT COVER GASKET PSB10510289 WOODRUFF KEY 4 X 13 PSB10510263 JACKSCREW PSB10510302 SHIFT SHAFT PSB10510264...

  • Page 170: Apron Front View

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Apron Front View -108-...
  • Page 171 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Apron Front View Parts List PART # DESCRIPTION PART # DESCRIPTION PSB10510401 COMBO GEAR 18T/60T PORP026 O-RING 25.7 X 3.5 P26 PSB10510402 THRUST WASHER AS3047 PSB10510430 SHAFT BRACKET...

  • Page 172: Apron Rear View

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Apron Rear View 462 463 PART # DESCRIPTION PART # DESCRIPTION PSTB001 STEEL BALL 1/4" PSB10510470 COMPRESSION SPRING 6 X 27 PSB10510422 GEAR 18T PRP04M ROLL PIN 4 X 24...

  • Page 173: Compound Rest & Tool Post

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Compound Rest & Tool Post 515A PART # DESCRIPTION PART # DESCRIPTION PSB10510501 LEVER PSB10510517 INDICATOR PLATE PSB10510502 TOOL POST NUT PSB10510518 LEADSCREW BRACKET PSB10510503 COLLAR...

  • Page 174: Saddle Top View

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Saddle Top View 613A -112-...
  • Page 175 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Saddle Top View Parts List PART # DESCRIPTION PART # DESCRIPTION PSB10510601 GIB ADJUSTMENT SCREW PSTB001 STEEL BALL 1/4" PSB10510602 CROSS SLIDE PSB10510629 COMPRESSION SPRING 6 X 15 PSB10510603...

  • Page 176: Saddle Bottom View

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Saddle Bottom View (Viewed from underneath the saddle) PART # DESCRIPTION PART # DESCRIPTION PSB10510641 SPACER 6.5 X 15 X 3 PSB10510649 OIL TUBE 6 X 160MM PSB10510642 GEAR 16T...

  • Page 177: Micrometer Stop

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Micrometer Stop Dial Indicator PART # DESCRIPTION PART # DESCRIPTION PSB10510700 MICROMETER STOP ASSEMBLY PSB10510750 DIAL INDICATOR ASSEMBLY PCAP71M CAP SCREW M10-1.5 X 60 PSB10510751 INDICATOR DIAL PRIV009M...

  • Page 178: Bed & Shafts

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Bed & Shafts -116-...
  • Page 179 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Bed & Shafts Parts List PART # DESCRIPTION PART # DESCRIPTION PSB10510801 PSB10510836A TAPERED BUSHING PSB10510802 CARRIAGE STOP BOLT PSB10510836A TAPER PIN #4 X 1-1/4" PB24M HEX BOLT M12-1.75 X 45 P51203...

  • Page 180: End Gears

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 End Gears PART # DESCRIPTION PART # DESCRIPTION PCAP02M CAP SCREW M6-1 X 20 PSB10510911 SPACER PSB10510902 GEAR FLAT WASHER 6MM PSB10510912 SHAFT COLLAR PSB10510903 GEAR 24T...

  • Page 181: Motor

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Motor -119-...

  • Page 182: Motor Parts List

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Motor Parts List PART # DESCRIPTION PART # DESCRIPTION 1001 PSB10511001 END GEAR COVER 1025 PSB10391025 TAPER PIN #4 X 1-3/4 1002 PSB10511002 KNURLED KNOB M10-1.5 1026...

  • Page 183: Stands & Panels

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Stands & Panels -121-...
  • Page 184 13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Cabinets & Panels Parts List PART # DESCRIPTION PART # DESCRIPTION 1101 PSB10511101 BRAKE PEDAL ROD 1127 PS65M PHLP HD SCR M4-.7 X 40 1102 PSB10511102 BRAKE PEDAL...

  • Page 185: Headstock Lubrication System

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Headstock Lubrication System -123-...
  • Page 186 13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Headstock Lubrication System Parts List PART # DESCRIPTION PART # DESCRIPTION 1201 PSB10511201 OIL TUBE ELBOW ADAPATER 3/8"PT X M6-1 1225 PSB10511225 LUBRICATION MOTOR 1/4HP 220V 3PH 1202 PSB10511202...

  • Page 187: Tailstock

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Tailstock 1301 1303 1346 1304 1306 1307 1308 1309 1305 1304 1314 1310 1313 1342 1343 1347 1344 1317 1341 1322 1321 1312 1318 1319...
  • Page 188 13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Tailstock Parts List PART # DESCRIPTION PART # DESCRIPTION 1301 PSB10511301 TAILSTOCK LEADSCREW 1332 PSB10511332 V-WAY WIPER 1302 PSB10511302 LEADSCREW NUT 1333 PSB10511333 V-WAY WIPER PLATE 1303...

  • Page 189: Steady Rest

    P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Steady Rest Follow Rest 1451 1401 1402 1400 1403 1404 1452 1453 1406 1405 1409 1407 1410 1454 1408 1411 1412 1456 1413 1455 1450...

  • Page 190: Electrical Cabinets & Control Panel

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Electrical Cabinets & Control Panel 1500 1501 1502 1503 1512 1507 1509 1509 1506 1504 1505 1504-1 1505-1 1508 1511 1510 1514 1514 1514 1515...
  • Page 191 P A R T S For Machines Mfg. Since 5/11 13" x 40" Heavy 13 ® EVS Lathe Electrical Cabinets & Control Panel Parts List PART # DESCRIPTION PART # DESCRIPTION 1500 PSB10511500 RPM DISPLAY NEWCAL SPP1406 1511 PSB10511511 OL RELAY AB 193T1AA40 2.5-0.4A 1501 PSB10511501 RESISTOR...

  • Page 192: Accessories

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Accessories 1552-1 1553 1554 1551 1552-2 1568 1550 1567 1566 1556 1552 1557 1559 1558 1560 1561 1564 1562 1563 1565 PART # DESCRIPTION PART # DESCRIPTION...

  • Page 193: Front Machine Labels

    The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

  • Page 194: Rear & Side Machine Labels

    13" x 40" Heavy 13 ® EVS Lathe P A R T S For Machines Mfg. Since 5/11 Rear & Side Machine Labels 1620 1622 1619 1620 1621 1624 1623 1620 1621 1622 PART # DESCRIPTION PART # DESCRIPTION 1600 PSB10511600 MODEL NUMBER BRASS PLATE 1613 PSB10511613...

  • Page 195: Warranty

    W A R R A N T Y Warranty This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance.
  • Page 196 Printed In U.S.A. #TS14550...

Table of Contents