Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Peri Manuals
  4. Construction Equipment
  5. SCS 190
  6. Instructions for assembly and use

Peri SCS 190 Instructions For Assembly And Use

Single-sided climbing formwork
Hide thumbs

Advertisement

Quick Links

Download this manual
SCS 190 and SCS 250
Single-Sided Climbing Formwork
Instructions for Assembly and Use – Standard Configuration - Version 2.0

Advertisement

loading
Need help?

Need help?

Do you have a question about the SCS 190 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Peri SCS 190

Summary of Contents for Peri SCS 190

  • Page 1 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration - Version 2.0...

  • Page 3: Table Of Contents

    Closing the Anchor Hole Corner Platforms Mounting the Access Ladder Components – Pre-assembly of the Ladder – Ladder Base – Bolting the Ladder 180/6 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 4 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 5: Overview

    Carriage 13 Concreting Platform Section A1.5 13 Working Platform Section A1.1 3+4 Bracket Section A1.3 13 Finishing Platform Section A1.4 Fig. 01 Fig. 02 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 6: Starter Brace Frame And Inclined Application

    3 + 4 brackets Section A1.3 5 - 8, 19 Starter Brace 13 Finishing Frame platform Section A2.2 Section A1.4 Fig. 03 Fig. 04 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 7: Key

    – Arrow representing forces C = Following Anchor wings must nevertheless be available. * if not identical to the action arrow SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 8: Combination Possibilities

    Positioning Plate + Screws Positioning Stud + Nails mostly inclined climbing units for lateral anti-fall protection with Guardrail Post Holder Multi according to static specifications SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 9: Anchoring In The Wall

    Spray the climbing cone with a release – Anchoring depth h agent before installation. – Screw-in depths  Facilitates easier removal. Concrete – Sufficient concrete strength – Cavity-free anchor base SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 10: Introduction

    The Crossbeam contains either sure with the Adjusting Unit. Striking is an Adjusting Unit (SCS 190) or an Adju- carried out by turning the Heavy Duty sting Unit with Carriage (SCS 250). The...

  • Page 11: Safety Instructions

    Deviations from the standard configurati- structions for Assembly and Use provi- on may only be carried out after a sepa- ded by PERI are available at all times for Use only suitable load-carrying equip- rate risk assessment has been com-...
  • Page 12 – Only PERI original components are to sufficient protection against falling, over- be used when replacing parts. turned, sliding or rolling objects and – Repairs are to be carried out by PERI masses. Cordon off areas of risk. qualified personnel only. Supporting structure: –...
  • Page 13 Secure all pins with cotter pins and all used if the power supply fails. bolts with nuts. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 14: Care And Maintenance Instructions

    Panel Formwork – Instructions of Use for the Crane Splice 24 – Instructions of Use for the Lifting Beam 10 t – SCS 190 and SCS 250 Dimensioning Information - Single-Sided Climbing Formwork* – PERI Design Tables – PERI Services –...

  • Page 15: Operating States

    The stability for the loads and condi- tions must be checked by means of a static calculation in accordance with separate SCS dimensioning informati- SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 16: Standard Operating Sequence

    - SCS 250 see A4.5. 3. Install Mounting Ring or Mounting Bolt, see A2.8. (without illustration) A2.6 A2.7 Section A2.6 A1.4 A2.5 Fig. 08 Fig. 09 Fig. 10 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 17: Moving

    5. If necessary: mount access ladder to the finishing platform, see A2.10. (Fig. 11) A2.6 A5.2 A5.3 A2.5 A2.4 Fig. 11 Fig. 12 Fig. 13 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 18: A1 Pre-Assembly

    Assembly with VT 20 Assembly with VT 20 13.5 13.5 13.1 13.1 13.8 13.8 (1500) (2000) 13.4 13.4 1911 2511 Fig. A1.01 Fig. A1.02 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 19 2 x wood screws 8 x 60 in each 40 x 50 mm. case. (Fig. A1.04c) (Fig. A1.01 or A1.02 + Fig. A1.04a) Fig. A1.04c SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 20: Platform Assembly With 80 X 160 Timber

    (13.7) or boards. Leave open gaps for anchor positions and diagonal struts.  No material or dirt falls through the gaps in the decking. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 21: Subsequent Assembly Of The Crossbeam

    (13.9), and se- cure with nails. Fig. A1.09 (Fig. A1.09) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 22: Hatch Installation

    20x TORX 6 x 40 (35). (Fig. A1.11) Fig. A1.11a Mount hatches and ladder access on corner platforms.  Free access to hatch possible. Fig. A1.11 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 23: Bracket Installation

    A1 Pre-Assembly SCS 190 SCS 250 A1.3 Mounting the brackets From the working platform with Cross- beam SCS 190 or SCS 250 mount the brackets with the following components. (Fig. A1.12a + A1.12b) Pos. Item no. Components per platform Vertical Strut SCS 237 118710 Fig.

  • Page 24: Platform Assembly With Vt

    2. Align board with platform. 3. Pre-drill board. 4. Connect Guardrail Post and boards using F .H. Bolt M8 x 100 and Nut M8. (Fig. A1.14) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 25 (14.4) to the Guardrail Post using Screw ISO4762-M8x70-8.8-ga. 4. Repeat steps 1 to 3 twice. (Fig. A1.18) M8 x 70 MU SW 13 Fig. A1.18 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 26: Assembling The Finishing Platform

    6 x 80 (2x per crossing). (Fig. A1.19b) 6. Cut out openings for the Platform „C” Posts SCS 232 (11). (Fig. A1.19c) Fig. A1.19c Centre line of bracket SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 27: Mounting Guardrails

    2. Align board on the platform. 3. Fix Guardrail Connector CB (14.4) to the Guardrail Posts (10) using Screw ISO4762-M8x70-8.8-ga 13.5 (Fig. A1.21) Fig. A1.21 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 28: Platform Assembly With Gt

    Assembly procedure is identical to Fig. A1.22b finishing platform, see A1.4 on previous page. „C” (Fig. A1.20 + A1.21) Fig. A1.22c Centre line of bracket SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 29: Mounting The Side Protection

    F .H. Bolts DIN 603 M8 x 100 MU M8 x 100 MU (6x) (Fig. A1.23 + A1.23a) (6x per holder). (Fig. A1.23a) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 30: Alternative Fall Protection

    Ø 6 x 80 4. Fix Toe Board on End Guardrail Posts (13.3) using F .H. Bolts M8 x 100 MU. (Fig. A1.25) Fig. A1.25 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 31 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 32: A2 Assembly On The Construction Site

    We recommend concreting a starter base ∆h as a stop in order to ensure the exact position and tightness of the form- work. (Fig. A2.01) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 33: Assembling The Starter Brace Frame

    – at the top on the Spindle Connector (5.1), – at the bottom on the Starter Bar (19). 9. Screw Anchor Bolt PERI 14/20 x 130 (28) onto the end of the Starter Bar.  Secure against tipping. Ø 26 10.
  • Page 34 Hex. Nut DW 15 SW 30/108 (20.5). Fig. A2.04 3. Tighten Wingnut Pivot Plate DW 15 (20.8) on the Tie Rod. (Fig. A2.04) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 35 – Perm. anchoring force per DW 15 = 80 kN. – Anchor inclination > 45°, e.g. if starter is inclined forwards at a large angle, see B4.3. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 36: Initial Use

    3. Lower platform unit and insert cross- beam heads into the Mounting Rings (16). (Fig. A2.06) Are both crossbeam heads completely and securely in the correct position? (Fig. A2.07a) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 37 Anchor to the formwork. Fig. A2.07 – If the mounting procedure is not pos- sible, correct the bracket spacing by modifying the platform. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 38: Connecting The Finishing Platform

    1. SCS 250: completely retract the Carri- age (2.1) and turn Heavy Duty Spindle (8) until the formwork reaches an an- gle of 2° to the rear. SCS 190: turn the Heavy Duty Spindle (8) until the form- work reaches an angle of approx. 8°...

  • Page 39: Tension Belt

    Ratchet Lever SW 19 (Item no. 027180) When not in use, wrap the Tension Belt around the guardrail of the finishing platform and secure. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 40: Fixing The Leading Anchor

    Check all individual components of the Leading Anchor, its as- assembly and the position of the anchor. sembly and the position of the anchor. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 41 Check all individual components of the Leading Anchor, their Check all individual components of the Leading Anchor, their assembly and the position of the anchor. assembly and the position of the anchor. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 42: Releasing The Leading Anchor

    (15.6) with Allen Key SW 14 and remove. (Fig. A2.13b) SW 14 Fig. A2.13b Tool Allen Key SW 14*. *For older Anchor Positioning Stud type, use Allen Key SW 12. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 43: Mounting Ring Or Mounting Bolt

    15.1 16.3 Removal: Release the Mounting Ring or Mounting Bolt and remove. Fig. A2.15b Tool Ratchet Wrench 1” with Screwdriver Bit SW 27-1” . SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 44: Closing The Anchor Hole

    Tool for Climbing Cone M30/DW 20: 29.2 – M36 Ratchet Wrench 1” with Socket SW 46-1” . M36/DW26: Ratchet Wrench 1” with Socket SW 55-1” . Fig. A2.16b SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 45: Mounting The Access Ladder

    110608) can also be installed. fore, install the ladder at an angle. – Assembly of the hatch (31) in the wor- king platform, see A1.6. Fig. A2.18 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 46: Pre-Assembly Of The Ladder

    Fix base rung (40.2) of the Ladder Base (40) to the planking of the finishing plat- form using 3x Torx 6 x 40 (43). Fig. A2.20 Fig. A2.21 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 47: Mounting The Ladder Safety Cage

    3. Fasten Safety Cage 2x below - as above, see Point 2. (Fig. A2.23 - shown without Hatch) M12 x 25 MU SW 19 Fig. A2.23 Fig. A2.23b SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 48: A3 Assembling The Formwork

    7 . Check the spacing of the Strongback (corresponds to bracket spacing c) at the bottom end and correct if necessary. (Fig. A3.02) 8. Securely fix Waler Fixation (7) using wingnut. (Fig. A3.01a) Fig. A3.01b SCS 190 und SCS 250 Einhäuptige Kletterschalung Aufbau- und Verwendungsanleitung – Regelausführung...

  • Page 49: Installing The Compression Brace

    The finishing platform can also be fixed Inclined formwork to the Platform Post (11) in an inclined position, see B5. M20 x 45 Fig. A3.04 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 50: Fixing The Formwork To The Brackets

    Spindle Connector. – Secure Fitting Pins with cotter pins. 11. Release crane lifting gear. Fig. A3.05 12. Align formwork, see A4.1 to A4.5. (Fig. A3.05) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 51: Exchanging The Formwork

    4. Open Waler Fixation (7) and remove 12. Remove bracing. (4x). 5 Carefully lift the formwork with the crane. If necessary, adapt Adjusting Unit (6) or offset (2x). SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 52: A4 Formwork Alignment

    4. Check the position of the Anchor Posi- tioning Stud or Anchor Positioning Plate. (Fig. A4.03) Tool Hammer or Tie Rod DW 15. Fig. A4.03 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 53: Operating The Adjusting Unit

    Fitting Pins. – Hole spacing in Crossbeam: 62.5 mm.  Adjusting Unit is in a secured position. SCS 250 Operating the Carriage, see A4.5. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 54: Operating The Carriage

    Unit (1.1), see A4.4 - Close the form- work Are cotter pins inserted into both Fitting Pins (1.2 + 1.4)? Tool Ratchet Wrench ½” with Socket SW 19- ½” L. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 55: A5 Crane-Assisted Climbing

    Lifting Beam RCS 10 t. For this, follow the Instructions for Fig. A5.01 Use for the Lifting Beam RCS 10t. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 56: Preparation

    2° to the rear, anchor (15). see A4.5 and A4.1. (Fig. A5.03) SCS 190: incline formwork approx. 8° to the rear, see A4.1. or, if necessary, determine inclination of the climbing unit by trial or error. Anchor position C: Remove Climbing Cone (15.1/15.7) and close...

  • Page 57: Iii. Mounting

    Mounting Rings, check the distance of the Climbing Anchor to the formwork. – If the mounting procedure is not possible, correct the bracket spacing by modifying the platform. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 58: Secured Position - Locking Pins

    *alternative: Mounting Bolt. Fig. A5.06 “X” View from the rear Fig. A5.06a SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 59: Released Position - Locking Pins

    2. Insert cotter pin (2.6) in the shaft (2.5) of the locking pin.  Climbing position (Fig. A5.07 + A5.07a) *alternative: Mounting Bolt. Fig. A5.07 “Y” View from the front Fig. A5.07a SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 60: A6 Dismantling The Climbing Formwork

    Fig. A6.01 Rings and move to the dismantling area. 6. Place finishing platform on the ground and release Bolts M20. (Fig. A6.02) Fig. A6.02 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 61 Fig. A6.04 accordance with the risk assessment of the contractor. Dispose of non-recyclable material in ac- cordance with the respective national re- gulations. Fig. A6.05 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 62: B1 Planning

    – Dimensions – Weight of the unit with formwork – Weight of the unit without formwork – Maximum formwork height – Permissible loads Fig. B1.01 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 63: Planning The Anchor Positioning Plate

    = 30 mm. Climbing Anchor M36: x = 40 mm. H = height measurement. 15.5/15.11 Position of the Anchor Positioning Plate. (Fig. B1.02) min. Fig. B1.02 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 64: B2 Dimensioning

    – Changes in inclination termined in separate static calculations. dimensioning information, – All other executions deviating from – determine through a separate static the standard case calculation. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 65: Influencing Factors

    – Material storage on the working – Materials can be left on the working materials can be left on the working platform allowed. platform. platform. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 66: Verifications

    When complying with the standard dimensions and permissible Finishing widths of influence, no proof is required. platform Fig. B2.03 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 67: Anchor Dimensioning

    Fig. B2.04 anchoring depth h nom. (Fig. B2.04) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 68: B3 Starter Heights

    – For very low starter heights, use addi- tional components or site-specific so- lutions with timbers. – The solutions for SCS 190 and SCS 250 are very similar. – The example shown is SCS 190. Starter height 2.80 - 3.00 m.
  • Page 69 Timber 160 x 160 mm – 1,50 m Fig. B3.05 For the Crossbeam Unit SCS 250, position the timber under the pressure point of the Carriage. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...
  • Page 70 Starter Bar SCS 187 118799 Tie Rod DW 15 - installed diagonally – Anchor Bolt PERI 14/20 x 130 124777 1,77 m Fig. B3.07 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 71: B4 Inclined Starter

    Starter Brace Frame (20). – When using standard formwork, the concreting height h must be redu- Fig. B4.02 ced. SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 72: B5 Inclined Climbing Units

    – Install Tension Belt (12) for increased system stability. (Fig. B5.01 + B5.01a) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 73: Forward Inclinations Of Up To

    Spindle (8) is free of play. (Fig. B5.02 + Fig. B5.02a) Pos. Item no. Components per climbing unit 123664 Connection Plate SCS Ø 21–125 Fig. B5.02a Fig. B5.02 SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 74: B6 Changes In Inclination

    – Anchor the vertical Tie Rod DW 20 (23) with Bracing Shoe SCS M36/DW 20 (21) for transferring the higher lift-off forces. Fig. B6.02 (Fig. B6.02) SCS 190 and SCS 250 Single-Sided Climbing Formwork Instructions for Assembly and Use – Standard Configuration...

  • Page 75: B7 Corner Platforms

    Bolts M24 x 130 and Nuts M24 to the crossbeam.  Additional intermediate platform beams are to be supported. SCS 190: Fig. B7 .02 + B7 .02a SCS 250: Fig. B7 .03 + B7 .03a 2. In the mitre area of the free ends of 13.1 13.1...

  • Page 76: Components

    SCS Single-Sided Climbing System Art no. Weight [kg] 118737 140.000 Crossbeam SCS 250 Platform Beam for climbing brackets with Adjusting Unit SCS and Carriage SCS to work for retracting the formwork. Notes Wrench Size Carriage SW19, Adjusting Unit SW30. 18 x 62,5 = 1125 9 x 125 = 1125...
  • Page 77 SCS Single-Sided Climbing System Art no. Weight [kg] 41.000 Diagonal Strut SCS 257 118714 Diagonal compression strut of the climbing bracket. M 30x140 Ø48,3 Ø48,3 M30x140 Included in delivery 017040 Screw-On Coupler DK 48 ga 2 pc 125999 Screw M30x140mm-8.8 coat 2 pc 725119 Hex Nut ISO7040-M30-8-ga 2 pc...
  • Page 78 SCS Single-Sided Climbing System Art no. Weight [kg] 118730 96.700 Crossbeam SCS 190 Platform Beam for climbing brackets with Adjusting Unit SCS to prevent tipping of the formwork. Notes Wrench Size Adjusting Unit SW30. 14 x 62,5 = 4 x 125 = Ø25x200...
  • Page 79 SCS Single-Sided Climbing System Art no. Weight [kg] 6.280 Guardrail Post SCS 150 118579 Guardrail post to connect handrail boards and toeboards. Ø21 Ø10 Ø10 Ø21 Accessory (not included) 113762 Guardrail Conn. Plate ACS/SCS 051160 Handrail Connector CB Art no. Weight [kg] 118578 23.900 Platform Post SCS 232 Rigidly suspension of the Finishing Platform SCS with Platform Beam SCS for single-sided application or use as Platform...
  • Page 80 SCS Single-Sided Climbing System Art no. Weight [kg] 51.700 Starter Bar SCS 118799 Basic bar for the erection of a brace frame for the starter. Ø26x120 Ø21 Ø48,3 Ø62 Ø26 1917 Included in delivery 017040 Screw-On Coupler DK 48 ga 2 pc 111567 Fitting Pin Ø26x120mm 1 pc 022230 Cotter Pin 5/1 ga 1 pc Art no.
  • Page 81 SCS Single-Sided Climbing System Art no. Weight [kg] 110022 0.491 Spacer M20x82mm Spacer for Climbing Rails RCS. SW 30 Included in delivery 104477 Screw ISO4014-M20x120-8.8-ga 1 pc 130341 Hex-Nut ISO7042-M20-8-ga 1 pc Art no. Weight [kg] 6.960 Height Adj. Unit-2 CB/SCS/RCS 129689 For height adjustment of RUNDFLEX Panels on the Strongbacks CB/RCS/SCS.
  • Page 82 SCS Single-Sided Climbing System Art no. Weight [kg] 46.300 Heavy Duty Spindle SCS 198-250 118585 Adjustable diagonal strut to support the strongback. 1980 max 2500 Ø26x120 1853 Included in delivery 111567 Fitting Pin Ø26x120mm 2 pc 022230 Cotter Pin 5/1 ga 2 pc Art no.
  • Page 83 SCS Single-Sided Climbing System Art no. Weight [kg] 1.400 Swivel Coupler SW Ø48/48mm ga 017010 For Scaffold Tubes Ø 48 mm. Notes Coupling category: B. SW 19 Art no. Weight [kg] 017020 1.120 Standard Coupl. RA Ø48/48mm ga For Scaffold Tubes Ø 48 mm. Notes Coupling category: B.
  • Page 84 SCS Single-Sided Climbing System Art no. Weight [kg] 0.884 Guardrail Conn. Plate ACS/SCS 113762 For assembling Scaffold Tubes Ø 48 mm or Ø 60 mm as Guardrail by means of Bail Pin A64 on Guardrail Posts ACS, SCS and GT 24. Fixation by Hex. Bolt M8, M12, M16 or Wood Screw Ø 8 mm. Ø13,5 Ø9 Ø18...
  • Page 85 SCS Single-Sided Climbing System Art no. Weight [kg] 4.390 Guardrail Post Holder Multi 126088 For fixing of an end guardrail post on Girders GT 24, VT 20 or KH 80/160. Fixing of the guardrail posts by means of Screws M20. Notes Suitable for Guardrail Post RCS 226 item no.: 109720 Guardrail Post RCS/SRU 184 item no.: 114328 Vertical scaffold tubes...
  • Page 86 SCS Single-Sided Climbing System Art no. Weight [kg] 0.865 Girder Connector M20 110330 For the fixation of 80 mm wide decking supports made of wood on Platform Beams with suitable boring of Ø 21 mm. Ø9 M20x40 Accessory (not included) 024470 Wood Screw 6x60 SK-TX30 HPI Included in delivery 706458 Screw ISO4017-M20x40-8.8-ga 1 pc 781053 Hex-Nut ISO7040-M20-8-ga 1 pc...
  • Page 87 SCS Single-Sided Climbing System Art no. Weight [kg] Tie Rods DW20 030700 2.560 Tie Rod DW20 spec. Length 030800 0.000 Cutting Costs DW20/B20 Notes Non-weldable! Observe Approval! Permissible tension force 150.0 kN. DW 20 Art no. Weight [kg] Tie Rods B20 030745 2.600 Tie Rod B20 spec. Length 030800 0.000 Cutting Costs DW20/B20 Notes...
  • Page 88 SCS Single-Sided Climbing System Art no. Weight [kg] 0.339 Advancing Screw M30x70 ga 029450 For fixing the M30 Anchor System if the plywood formlining is drilled through. M 30 SW 19 Accessory (not included) 029380 Anchor Posit. Plate M30 ga Art no. Weight [kg] 029380 0.184 Anchor Posit.
  • Page 89 SCS Single-Sided Climbing System Art no. Weight [kg] 2.550 Mounting Ring SCS M36 118772 For anchoring of the SCS Bracket at high tension forces and vertical loads. SW 27 Accessory (not included) 030940 Climbing Cone-2 M36 DW26 Art no. Weight [kg] 030940 2.980 Climbing Cone-2 M36 DW26 Tie System M36.
  • Page 90 Art no. Weight [kg] 131709 9.980 Sealing Adhesive-3 6-Cans-Set For bonding PERI Concrete Cones. Notes See Safety Data sheet! Consisting of: 6 x Component A, 6 x Component B Component A = Net quantity / Can 459 ml / 752 g...
  • Page 91 SCS Single-Sided Climbing System Art no. Weight [kg] 0.170 Anchor Posit. Plate M36 ga 029390 For fixing the M36 anchor system if the plywood formlining is drilled through. Ø7 Ø36,5 Accessory (not included) 029440 Hex-Wood Screw DIN571-6x20-ga Art no. Weight [kg] L [mm] 029430 0.930 Screw ISO4017-M36x70-8.8-ga Bolt for anchoring of climbing systems and as advancing bolt.
  • Page 92 SCS Single-Sided Climbing System Art no. Weight [kg] 9.610 Bracing Shoe SCS DW20 M36 123819 Used as compression point at starter sections with optional connections to Scaffold Tube Bracing Ø 48 mm, Vertical Tie Rod DW20 Suspension, Climbing Anchor M36, Diagonal Strut SCS or Heavy Duty Spindle SCS. Ø26 Ø37 Ø31...
  • Page 93 SCS Single-Sided Climbing System Art no. Weight [kg] 0.786 Wingnut DW20 ga 030990 For anchoring with Tie Rod DW20 or B20. Notes Permissible load 150.0 kN. DW 20 SW 36 Art no. Weight [kg] 051250 2.790 Tension Belt 570/25kN For preventing climbing systems tipping over due to the wind. Notes Follow relevant Instructions for Assembly and Use for the system.
  • Page 94 SCS Single-Sided Climbing System Art no. Weight [kg] 0.065 Hex-Nut ISO7040-M20-8-ga 781053 Self-locking. M 20 SW 30 Art no. Weight [kg] 131352 5.130 Tie Yoke Ø60x250xØ18mm Ø18 Ø8 Art no. Weight [kg] 030100 0.439 Wingnut DW15 ga For anchoring with Tie Rod DW15 or B15. Notes Permissible load 90.0 kN.
  • Page 95 SCS Single-Sided Climbing System Art no. Weight [kg] L [mm] Steel Walers SRU U120 103874 30.900 Steel Waler SRU 122 U120 1222 103877 38.100 Steel Waler SRU 147 U120 1472 103886 44.700 Steel Waler SRU 172 U120 1722 103889 52.000 Steel Waler SRU 197 U120 1972 103898 58.600 Steel Waler SRU 222 U120...
  • Page 96 SCS Single-Sided Climbing System Art no. Weight [kg] Tie Rods DW15 030030 1.440 Tie Rod DW15 spec. Length 030005 0.720 Tie Rod DW15 0.5m 030050 0.000 Cutting Cost DW15/B15 Notes Non-weldable! Observe Approval! Permissible tension force 90,0 kN. DW 15 B 15 Art no. Weight [kg] 030840 0.515 Threaded Anchor Plate DW15...
  • Page 97 SCS Single-Sided Climbing System Art no. Weight [kg] L [mm] 0.560 Ratchet Wrench 1/2 „ 072180 Art no. Weight [kg] L [mm] 029610 5.300 Ratchet Wrench 1“ Art no. Weight [kg] 0.216 Socket SW19 1/2“ 123751 Fits to Hex. Bolts M12. To operate the Carriage SCS with Drive Shaft SW19. SW 19 Art no.
  • Page 98 Fits to Screw ISO4762-M36. SW 27 Art no. Weight [kg] 027212 0.445 Hexag. Recess Wrench SW14 long Fits PERI Positioning Discs and Allen Key Bolts M16. SW 14 Art no. Weight [kg] 118575 16.800 Adjusting Unit SCS Spare part for Crossbeam Unit SCS.
  • Page 99 SCS Single-Sided Climbing System Art no. Weight [kg] 23.500 Carriage SCS 118690 Spare part for Crossbeam Unit SCS 250. Ø26 Ø17 1600 Included in delivery 103740 Screw ISO4016-M16x280-4.6ga-Nu 2 pc 070890 Hex-Nut ISO7040-M16-8-ga 2 pc Art no. Weight [kg] 126431 12.300 Hatch-2 RCS 55x60 foldable Self-closing hatch for ladder access.
  • Page 100 710224 Screw ISO4017-M12x40-8.8-ga 4 pc 710381 Hex-Nut ISO7040-M12-8-ga 4 pc Art no. Weight [kg] 103724 10.400 End Ladder 180/2 cpl As access for PERI Formwork Systems. 1200 1885 Included in delivery 710224 Screw ISO4017-M12x40-8.8-ga 4 pc 710381 Hex-Nut ISO7040-M12-8-ga 4 pc...
  • Page 101 Weight [kg] Ladder Safety Cages 104132 15.600 Ladder Safety Cage 75 051450 25.200 Ladder Safety Cage 150 Ladder cage for PERI Ladder Access. SW 19 Included in delivery 710266 Screw ISO4017-M12x25-8.8-ga 4 pc 701763 Clamping Plate FL 25x10x90mm 4 pc...
  • Page 102 SCS Single-Sided Climbing System Art no. Weight [kg] 8.100 Ladder Connector VARIO adj. 111165 For connecting ladders to Steel Walers SRZ or SRU Profile U100 – U120. U100 / U120 min 0 max 111 Included in delivery 710266 Screw ISO4017-M12x25-8.8-ga 2 pc 701763 Clamping Plate FL 25x10x90mm 2 pc...
  • Page 104 PERI Norge AS Forskaling Stillas Engineering Orhusveien 6 3070 Sande i Vestfold Norge Tel. +47 32 20 49 40 info@peri.no www.peri.no...

This manual is also suitable for:

Scs 250