Winmate E Series User Manual
Hmi display
Hide thumbs
Also See for E Series:
- User manual (64 pages) ,
- Quick start manual (32 pages) ,
- User manual (64 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Winmate E Series
Summary of Contents for Winmate E Series
- Page 1 E-Series HMI Display Model No. W07L100-EHT1 W10L100-EHH2 R15L100-EHC3 W15L100-EHA4 W22L100-EHA3 User Manual Document Version : 1.0 Document Part Number : 91521110104B Please read these instructions before operating the device and retain them for future reference.
-
Page 2: Table Of Contents
E-Series HMI Display User Manual Contents PREFACE ..............................2 ABOUT THIS USER MANUAL ........................ 6 CHAPTER 1: INTRODUCTION........................ 7 1.1 Features ............................7 1.2 Package Contents .......................... 7 1.3 Product Overview ........................... 8 1.4 Connector Description ........................11 1.5 OSD Control Panel ........................11 1.6 LED Indicators .......................... -
Page 3: Preface
Preface Preface Copyright Notice No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners. -
Page 4: Advisory Conventions
E-Series HMI Display User Manual In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Advisory Conventions Four types of advisories are used throughout the user manual to provide helpful information or to alert you to the potential for hardware damage or personal injury. -
Page 5: Safety Precautions
Preface Caution/ Attention Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. - Page 6 E-Series HMI Display User Manual • Do not leave this equipment in an uncontrolled environment where the storage temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the equipment. CAUTION/ATTENTION Use the recommended mounting apparatus to avoid risk of injury. Utiliser l’appareil de fixation recommandé...
-
Page 7: Ec Declaration Of Conformity
• EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013 About this User Manual This User Manual provides information about using the Winmate® E-Series HMI Display. This User Manual applies to the E-Series HMI –W07L100-EHT1, W10L100-EHH2, R15L100-EHC3, W15L100-EHA4 and W22L100-EHA3. The documentation set for the E-Series HMI with Freescale® Cortex® A9 i.MX6 Dual Core provides information for specific user needs, and includes : •... -
Page 8: Chapter 1: Introduction
E-Series HMI Display User Manual Chapter 1: Introduction Congratulations on purchasing Winmate® E-Series HMI Display. Versatile display in an open- frame housing designed for panel mount and VESA mount solutions for industrial applications. 1.1 Features Winmate® Multi-Touch PCAP Panel Mount Display offers the following features: •... -
Page 9: Product Overview
Chapter 1: Introduction 1.3 Product Overview This section describes physical appearance of the Multi-Touch PCAP Panel Mount Display. Note: Notice that standard input terminals include VGA and HDMI. Your device may be equipped with other input terminals based on your order. Note: Notice that input and output connectors vary by product size and specifications. - Page 10 E-Series HMI Display User Manual 10.1-inches, W10L100-EHH2 Unit: mm № № Description Description USB for Touch HDMI OSD Control Panel Power Input 15-inches, R15L100-EHC3 Unit: mm № № Description Description USB for Touch HDMI OSD Control Panel Power Input...
- Page 11 Chapter 1: Introduction 15.6-inches, W15L100-EHA4 Unit: mm № № Description Description USB for Touch Power Input OSD Control Panel HDMI 21.5-inches, W22L100-EHA3 Unit: mm № № Description Description USB for Touch Power Input OSD Control Panel HDMI...
-
Page 12: Connector Description
E-Series HMI Display User Manual 1.4 Connector Description This section describes the Input/Output Ports of the display. Note: Notice that standard input terminals include VGA and HDMI. Your device may be equipped with other input terminals based on your order. Notice that input and output connectors vary by product size and specifications. -
Page 13: Led Indicators
Chapter 1: Introduction 1.6 LED Indicators LED indicators are located in the OSD Control Panel on the rear side of the display. Item Description Function Power Indicator Lights up in "Green" when the monitor is on. Lights up in "Orange" when the device cannot detect any Stand by Indicator input source. -
Page 14: Chapter 2: Hardware Installation
E-Series HMI Display User Manual Chapter 2: Hardware Installation 2.1 Wiring Requirements The following common safety precautions should be observed before installing any electronic device: • Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point. -
Page 15: Panel Mount
Chapter 2: Hardware Installation 2.2.1 Panel Mount The E-Series Display comes with clamp mounts that enable you to install the unit onto a wall (where space has been cut out to accommodate the rest of the hardware). Installation Instructions 1. Cut an opening in the fixture (e.g., wall) based on the display’s cutout dimensions. Mark the screw holes on the front side of the fixture using the provided drawing. -
Page 16: Vesa Mount
2.2.2 VESA Mount Panel Mount Display comes with VESA holes for wall/ desk mounting. Notice that VESA stand and mounting kit are not provided by Winmate. Installation Instructions 1. Secure the VESA bracket to the fixture (e.g., swing arm) using the four provided VESA screws. -
Page 17: Cable Mounting Considerations
Chapter 2: Hardware Installation 2.3 Cable Mounting Considerations For a clean appearance and secure installation, ensure all cables are neatly concealed behind the device. Caution Observe all local installation requirements for connection cable type and protection level. Attention Suivre tous les règlements locaux d’installations, de câblage et niveaux de protection. -
Page 18: Connecting Peripherals
E-Series HMI Display User Manual 2.5 Connecting Peripherals The panel control port is designed for monitors that work with a variety of compatible video sources. Due to the possible deviations between these signal sources, you may have to make adjustments to the monitor settings from the OSD menu when switching between these sources. 2.5.1 VGA Connector Panel Mount Display uses standard 15pin D-sub connector. -
Page 19: Chapter 3: Operating The Device
Chapter 3: Operating the Device Chapter 3: Operating the Device This chapter describes the instructions on how to operate the display. 3.1 Turning on the System To turn on the system: 1. Connect the power adapter cable to the DC input of the display. 2. -
Page 20: Osd Menu Navigation
E-Series HMI Display User Manual 3.2 OSD Menu Navigation OSD Icon Sub-menu Settings Note BRIGHTNESS Slider bar Default 50 Use to adjust the screen’s brightness. Range 0 to 100 CONTRAST Slider bar Default 50 BRICONTRAST Use to adjust the screen’s contrast. Range 0 to 100 H POSITION Slider bar Default 50... - Page 21 Chapter 3: Operating the Device OSD Icon Sub-menu Settings Note AUTO SCAN Select and execute Default mode Auto detect the input source ANALOG Select and execute CHANNEL* Switch the setting of signal input to Analog mode HDMI Select and execute Switch the setting of signal input to HDMI mode Select and execute Recall the factory default setting...
-
Page 22: Troubleshooting Guide
E-Series HMI Display User Manual 3.3 Troubleshooting Guide If your monitor fails to operate correctly, check the following chart for possible solution before calling for repairs: Condition Check Point • Check if the signal cable is firmly seated in the socket. •... -
Page 23: Appendix
Appendix Appendix Appendix A: Resolution Table V-VGA D-DVI H-HDMI Resolution Support Table 15.6", 18.5", 8", 8.4", 10.4", Panel Size 5.7", 6.5" 7" 7", 10.1" 10.1", 12.1" 17", 19" 15.6", 18.5" 20.1", 23.1" 21.5", 23.8", 10.1", 24" 12.1" 12.1", 15" 27", 32", 42" Panel Native 640 x 480 800 x 480... -
Page 24: Appendix B: Frequency Table
E-Series HMI Display User Manual Appendix B: Frequency Table Frequency Table Vertical Resolution Frequency 640x480 (4:3) 480P 800x480 800x600 (4:3) 1024x768 (4:3) 1280x720 (16:9) 720P 1280x768 1280x800 (16:10) 1280x1024 (5:4) 1366x768 1400x1050 (4:3) 1440x900 (16:10) 1600x1200 (4:3) 1680x1050 (16:10) 1920x1080 (16:9) 1080P 1920x1200 (16:10) - Page 25 Notes...
- Page 26 Notes...
- Page 27 Notes...
- Page 28 E-mail: info@tl-electronic.de Website: www.tl-electronic.de 北京京融电自动化科技有限公司 苏州办事处 215100 江苏省苏州市工业园区唯新路 69 号 一能科技园 3 号楼 206 室 Tel: +86-512-6826-6696/6829-6696 E-mail: sales@winmate.com.cn Website: www.winmate.com.cn Winmate JP Office/ HPC System Inc. LOOP-X 8F,3-9-15 Kaigan, Minato-ku, Tokyo 108-0022, Japan Tel: +81-3-5446-5535 Fax: +81-3-5446-5550 Website: www.hpc.co.jp...
Need help?
Do you have a question about the E Series and is the answer not in the manual?
Questions and answers