Download Print this page
CommScope RUCKUS T350d Quick Setup Manual
CommScope RUCKUS T350d Quick Setup Manual

CommScope RUCKUS T350d Quick Setup Manual

Advertisement

Quick Links

T350d Access Point
Quick Setup Guide
NOTE: The minimum software revision for the T350d is ZoneDirector
(ZD) 10.5 or later, or SmartZone (SZ) 6.0 or later.
This Quick Setup Guide provides step-by-step instructions on how to field-
install the RUCKUS T350d access point (AP). For detailed information on
planning the installation, performing a site survey, and operating the
T350d, refer to the RUCKUS Outdoor Access Point User Guide, available at
https://support.ruckuswireless.com.
WARNING! Only trained and qualified personnel should be allowed to
install, replace, or service this equipment.
WARNING! Installation of this equipment must comply with local and
national electrical codes.
CAUTION! Form a 80-mm to 130-mm (3-in. to 5-in.) drip loop in any
cable that is attached to the AP or the building. This will prevent water
from running along the cable and entering the AP or the building where
the cable terminates.
CAUTION! Be sure that grounding is available and that it meets local
and national electrical codes. For additional lightning protection, use
lightning rods and lightning arrestors.
CAUTION! Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
CAUTION! RUCKUS strongly recommends that you wear eye protection
before mounting the T350d.
This Guide in Other Languages
• 请从以下网站获得该指南的简体中文版
https://
support.ruckuswireless.com.
• Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com.
• このガイドの日本語版は
https://support.ruckuswireless.com
ください。
• 이 가이드의 한국어 버전은 웹 사이트
(https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
• Veja a versão em português (Brasil) deste guia em
support.ruckuswireless.com.
• Puede ver la versión en español (América Latina) de esta guía en
support.ruckuswireless.com.
Copyright
©
2024 CommScope, Inc. All rights reserved.
Published March 2024, Part Number 800-72681-001 Rev D
Before You Begin
Before deploying RUCKUS products, please check for the latest software
and the release documentation.
• Release Notes and other user documentation are available at
support.ruckuswireless.com/documents.
• Software upgrades are available at
software.
• Software license and limited warranty information are available at
http://support.ruckuswireless.com/warranty.
• Before deploying your RUCKUS Access Point, verify that all items listed
in Package Contents are included in the package. If any item is damaged
or missing, notify your authorized RUCKUS sales representative. Also,
make sure that you have the required hardware and tools.
Required Hardware and Tools
• No. 2 Phillips screwdriver
• Small flat-blade screwdriver
• Wide flat-blade screwdriver
• Torque wrench or torque screwdriver with sockets
• Long-nose pliers
• Electrical wire stripping and terminal crimping pliers
• Pipe or pole, or a sturdy flat surface
• Electric drill with drill bits and customer-supplied wall anchors, flat
washers, and hex nuts for flat-surface mount
Package Contents
A complete T350d field installation package includes all of the following
items:
• T350d Access Point
• M25 data cable gland
• Ground wire with lug
• Pole/Wall Mount Bracket Kit
• Two steel pipe clamps
• Declaration of Conformity/Regulatory Statement
FIGURE 1 T350d Package Contents
でご覧
1. T350d Access Point
2. M25 data cable gland
https://
https://
Omni Antenna Coverage
The AP (ordering part number 901-Txxx-xx-01) is best deployed where
internal-antenna lateral beamforming can provide the greatest reach and
throughput to a wide coverage area, or to provide the greatest distance
http://
between APs in a connecting mesh device. See
typical side view coverage pattern, see
http://support.ruckuswireless.com/
pattern, and see
FIGURE 2 Typical AP Omni Coverage, Side View - Option1
1. Limited Reach
2. Good Reach
FIGURE 3 Typical AP Omni Coverage, Side View - Option2
3. Ground wire with lug
FIGURE 4 Typical AP Mesh Elevation Plane Coverage, Side View
4. Pole/Wall Mount Bracket Kit
Figure 2
and
Figure 3
Figure 4
for a typical mesh coverage
Figure 5
for a typical top view coverage pattern.
3. Excellent Reach
Page 1 of 4
for a

Advertisement

loading
Need help?

Need help?

Do you have a question about the RUCKUS T350d and is the answer not in the manual?

Questions and answers

Summary of Contents for CommScope RUCKUS T350d

  • Page 1 This Quick Setup Guide provides step-by-step instructions on how to field- 1. Limited Reach 3. Excellent Reach • Small flat-blade screwdriver install the RUCKUS T350d access point (AP). For detailed information on • Wide flat-blade screwdriver planning the installation, performing a site survey, and operating the 2. Good Reach T350d, refer to the RUCKUS Outdoor Access Point User Guide, available at •...
  • Page 2 6. Using the mounting hardware instructions, tighten the hardware to secure the mounting bracket. 7. Continue with Mounting the AP on page 3. Copyright © 2024 CommScope, Inc. All rights reserved. Page 2 of 4 Published March 2024, Part Number 800-72681-001 Rev D...
  • Page 3 You have completed mounting the AP to the mounting bracket. Powering the AP with DC Power The AP can accommodate two sources of power: PoE (48V) power and 12V Copyright © 2024 CommScope, Inc. All rights reserved. Page 3 of 4 Published March 2024, Part Number 800-72681-001 Rev D...
  • Page 4 CommScope and the CommScope logo are registered trademarks of the cap, and insert the dongle into the USB port. CommScope and/or its affiliates in the U.S. and other countries. For additional Once installed, replace the cap and the hex screws, and tighten the screws trademark information see https://www.commscope.com/trademarks. ...