Basic Operation; Power On/Off; Volume Control - Jensen MSR3007 Installation And Operation Manual

MSR3007

BASIC OPERATION

1
4 24
POWER
2a
VOLUME
13 MODE +
CAT SEL CAT
2b VOLUME
1 2
MUTE INT
17 18 6
14 8

Power On/Off

Press any button on the front panel to turn the unit on. Press the POWER button (1) to turn the
unit off.
• If a disc is being inserted when the radio power is off and the ACC (accessory switch) is
on, the unit will automatically power up and playback will start.
• If a CD is present, playback resumes at the last position in memory before the ignition
was turned off or the POWER button was pressed.
• If no CD is present, the unit will resume at the last mode selected (Tuner, Aux, etc.). The
POWER button is illuminated whenever the IGN lead (red wire) is powered, regardless of
whether the unit is on or off.

Volume Control

To increase the volume, press the VOLUME + button (2a). To decrease the volume, press the
VOLUME - button (2b).
Mute
Press the MUTE button (17) on the control panel to mute the audio output. Press MUTE again
to restore the audio output to the previous level.
Mode
Press the MODE button (4) on the control panel to select a different mode of operation, as
indicated on the display panel. Available modes include Tuner, SIRIUS, CD, iPod and AUX In
(optional Auxiliary Input).
NOTE: CD, CDC, IPOD, or SIRIUS mode will be skipped if the module is not installed.
Reset
The reset button should be activated for the following reasons:
• initial installation of the unit when all wiring is completed
• function buttons do not operate
22
23 12 11 3
EQ
AUDIO
IX BASS MENU
TUNE/TRK
SEEK
INFO
SEEK
SCROLL
TUNE/TRK
BAND
SEARCH
40W x 4
AUX
IN
3 4 5 6
RPT RDM
AS/PS
5 7 9 10 15
16 19
• error symbol on the display
Use a ball point pin or thin metal object to press the RESET button (18). This may be
necessary should the unit display an error code.
You can recover factory default settings using the RESUME function located on the system
menu. With "YES" flashing, press the MODE button (4) to activate.
Audio Menu
21
Press the AUDIO button (3) on the control panel to access the audio menu. You can navigate
20 through the audio menu items by pressing the AUDIO button repeatedly. Once the desired
menu item appears on the display, adjust that option by pressing the VOLUME +/- buttons (2)
within 5 seconds. The unit will automatically exit the audio menu after five seconds of inactivity.
The following menu items can be adjusted.
Bass Level
Use the VOLUME buttons to adjust the Bass level range from "-6" to "+6".
Treble Level
Use the VOLUME buttons to adjust the Treble level range from "-6" to "+6".
Balance
Use the VOLUME buttons to adjust the Balance between the left and right speakers from "L12"
(full left) to "R12" (full right).
Fader
Use the VOLUME buttons to adjust the Fader between the rear and front speakers from "R12"
(full rear) to "F12" (full front).
Volume Level
Use the VOLUME buttons to adjust the Volume level.
System Menu
1. Press and hold the AUDIO button (3) for more than 3 seconds to enter the system menu.
"MENU" will appear on the display, followed by the first menu item, "CONTRAST."
2. Press the TUNE/TRK >>| or |<< button (21, 20) or press the AUDIO button repeatedly to
navigate the system menu and select the desired item.
3. Press the VOLUME +/- buttons (2) to adjust the selected menu item.
4. Press the AS/PS button to return to the previous operation immediately or wait for 5
seconds to return automatically.
The following items can be adjusted:
• CONTRAST (0 – 10): Set LCD contrast.
• LOW BATT (ON/OFF): Monitor voltage on ACC line.
• MWR100 (ON/OFF): Enable or disable MWR100 external wired remote operation.
• AREA (USA/LATIN/EUROPE/OIRT): Set frequency spacing for various regions.
• VOL PGM (0 – 46): Select an automatic turn-on volume.
• BEEP TONE (ON/OFF): Turn the audible beep ON/OFF (heard when functions/buttons
are selected). NOTE: Beep tone off will not affect LOW BATT audible tone.
• RESUME: Return the EEPROM to factory default set up values and reset the Sirius Tuner
Settings. "Yes" will blink on the LCD to confirm. Press MODE to select.
5