Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CAME TA/350
Summary of Contents for CAME TA/350
- Page 1 FA02072-EN Digital thermostat TA/350 INSTALLATION AND USE MANUAL EN English...
-
Page 2: General Warnings
General warnings • Read the instructions carefully before starting installation and proceed as specifi ed by the manufacturer. • Installation, programming, commissioning and maintenance of the product must only be performed by qualifi ed technicians who have been properly trained in compliance with current standards, including health and safety and packaging disposal regulations. -
Page 3: Installation
Installation Package contents Frame Main body Fastening screws ☞ Some counter frames and corresponding hole-cover adapters are provided with the product. The counter frames and hole-cover adapters, when properly matched, can be used to adapt the device to most standard industry series. SCAN THIS QR CODE TO DOWNLOAD THE INSTRUCTIONS FOR MATCHING AND/OR ADAP- TING COUNTER FRAMES AND HOLE-COVER ADAPTERS TO INDUSTRY SERIES FOUND ON THE MARKET. - Page 4 Install the unit in a suitable position to cor- rectly detect the temperature, possibly in an internal wall, avoiding installation in niches, behind doors, curtains or near heat sources. Pull out the tab L and then pull the unit body out from the frame as far as it will go Press on the side fl...
- Page 5 Wiring The connections are made depending on the type of equipment controlled by the programmable thermostat. Mains power supply wires NCNA C N = neutral L = phase Relay contacts C = common NO = normally open contact NC = normally closed contact Loads U1 = burner, circulation pump, solenoid valve etc.
- Page 6 Installation Once the chosen frame and subframe have been assembled and wiring has taken place, assemble the programmable thermostat as shown in the fi gure...
-
Page 7: Device Description
Device description Description of the icons on the display and function of the front buttons ① ① ② ② ③ ③ ④ ④ ⑤ ⑤ ⑥ ⑥ ⑦ ⑦ ⑧ ⑧ ⑨ ⑨ ⑯ ⑯ ⑩ ⑪ ⑪ ⑮ ⑮ ⑭... - Page 8 Function of internal buttons To access the internal command buttons, pull out the tab ⑬ and then the unit body from the frame. ⑰ ⑱ ⑲ ⑳ ㉑ ㉒ ㉓ ㉔ ⑰ Reset button. ⑱ Setting the clock. ⑲ Setting the operating parameters. Selecting the operating mode: ⑳...
-
Page 9: Using The Device
Using the device Setting the clock TA350 Pull out the unit body. Press the button to display the clock. Press the button The minute digits fl ash. Use the buttons to set the exact minute value TA350 Press the button The hour digits fl... - Page 10 TA350 Press the button to fi nish the time and day setting procedure The colon between the hours and minutes will fl ash confi rming the operation has been completed. ☞ After 15 seconds of inactivity, the unit automatically exits the procedure, storing the last data set.
- Page 11 Changing the user profile TA350 The device is able to manage the tempera- ture preferences of two user profi les. For each user profi le, several programs can be created - "Comfort", "Eco", "Night" mode for heating and cooling modes. To change the active user, press the but- Changing the pre-programmed temperature levels TA350...
-
Page 12: Setting The Operating Mode
Manually forcing the desired temperature With any active temperature management program (Eco, Comfort, Night), use the buttons to change the desired pro- grammed temperatures. The new desired temperature is displayed instead of the detected temperature. Any icon of the active program and the active user ( ) disappear to indicate that the programming has been edited. - Page 13 Confi guring the general device parameters. Editing the default frost protection temperature TA350 Press the button The display shows the default frost protec- tion temperature (3 °C). Use the buttons to edit the pro- grammed temperature (max 16 °C). Press the button to exit and save the set data.
- Page 14 Setting the type of temperature management algorithm The device allows you to choose the type of algorithm to be applied for system management from diff erential and integral proportional. Activating and confi guring a diff erential algorithm This control system is recom- + diff erential mended in systems that are par- setpoint...
- Page 15 Use the buttons to set the diff erential value at a value between 0 °C and 0.9 °C By setting the diff erential to 0 °C, during operation, a minimum switching on/off time of 1 minute is respected, regardless of the detected room temperature.
- Page 16 Setpoint Time If you have chosen the P4 program, pressing button P gives access to the programming of the individual parameters that make up the manual P4 program. The graph can help you decide the value of the parameters to be entered. TA350 The fi...
- Page 17 TA350 to confi rm the minimum Press button P ON time and switch to adjusting the pro- portional band. Use the buttons to adjust the value of the proportional band to between 1 and 3 °C. Press button P to exit programming. ☞ ...
- Page 18 Enabling and configuring the remote control function By connecting a special interface to terminals 1-2 (see "Wiring"), it is possible to remotely change the operating mode of the device. To select the desired mode (cooling or heating), proceed as follows. TA350 button Press the...
-
Page 19: Resetting The Device
Use the buttons to choose one of the 2 possible magnetic confi gurations = Contact enabled = Contact not enabled After a few seconds of inactivity, the choice made is recorded. If an enabled contact is opened ( the activation is displayed as shown in fi g- ☞ ... -
Page 20: Replacing The Batteries
- Contacts available: 1 x NO-NC changeo- - Operating temperature: from 0 °C to ver contact. +40 °C. CAME S.p.A. Via Martiri Della Libertà, 15 31030 Dosson di Casier - Treviso - Italy tel. (+39) 0422 4940 - fax. (+39) 0422 4941...
Need help?
Do you have a question about the TA/350 and is the answer not in the manual?
Questions and answers