Table of Contents
Advertisement
Quick Links
Core and Tilt Motor
Electronic
Limit
Use this document with the following motors:
Part Number
MT01-4001-xxx002
MT01-4001-069003
INSTR_TILT_PRGM_v2.1_SEP_2023
1 | Automate
Programming Instructions | Tilt Motors
™
Adjustable
Speed
Bi-Directional
Precise
Tilt Control
Detection
Description
12V Core Tilt Motor Kit
AUTOMATE | VT TILT [12V/0.6Nm/11rpm]
433 Mhz
Favorite
Position
Impact
Solar
Option
Soft
Stop
A Division of Rollease Acmeda
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for rollease acmeda Automate MT01-4001 002 Series
Summary of Contents for rollease acmeda Automate MT01-4001 002 Series
- Page 1 Tilt Control Detection Stop Use this document with the following motors: Part Number Description MT01-4001-xxx002 12V Core Tilt Motor Kit MT01-4001-069003 AUTOMATE | VT TILT [12V/0.6Nm/11rpm] INSTR_TILT_PRGM_v2.1_SEP_2023 1 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™...
-
Page 2: Safety Instructions
• The A-weighted emission sound pressure level of the appliance is less than or equal to 70dB(A). 2 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 3: Safety Instructions
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement. 3 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 4: Compliance Statement
• - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 4 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 5: Table Of Contents
8.2 Using a pre-existing controller to add or delete a controller or channel Favorite Positioning 9.1 Set a favorite position 9.2 Send shade to favorite position 9.3 Delete favorite position 5 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 6: Core Tilt Motor Assembly
• Insert motor assembly into existing venetian head rail assembly • Re-insert tilt rod through the motor assembly & spools • Attach switch control cover Battery Charging 6 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 7: Core Tilt Motor Wand Operation
Core Tilt Motor Wand Operation Optional Control Wand 7 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 8: Tilt Motor Assembly
• Ensure tilt rod is engaged with the motor • Minimum tilt rod insertion with motor is 1/2” • Maximum tilt rod insertion with motor is 3/4” Battery Charging 8 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 9: Wiring
A/C power supplies are available, with a variety of quick connect extension cords. For centralized installations, power supply range can be extended with 18/2 wire (not available through Rollease Acmeda). • During operation, if voltage drops to less than 10V, the motor will beep 10 times to indicate a power supply issue. -
Page 10: P1 Button Functions
Ignore this icon when programming mt01-4001- 069003. Approx. Approx. Approx. All other prompts are the same for both motors. Reset To Factory Settings Approx. Approx. Approx. Approx. 10 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 11: Initial Set Up
Damage to shade may occur when operating motor prior possible during initial set-up to setting limits. Attention should be given. NOTE: * Only The Pass-through Motor Beeps 11 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 12: Initial Set Up
DOWN buttons on controller. Motor Response* Approx. IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 12 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 13: Adjusting Limits
The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised. NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 13 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 14: Controllers And Channels
A. remove it. Motor Response* Motor Response* Motor Response* IMPORTANT Consult user manual for your controller or sensor NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 14 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 15: Favorite Positioning
Delete favorite position Press P2 on controller. Press STOP Press STOP on controller. on controller. Motor Response* Motor Response* Motor Response* NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 15 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 16: Adjusting Speed
NOTE: Repeating this step when at the slowest speed EXITS Soft Stop Mode in MT01-4001-069001. Press P2 Press DOWN Press DOWN Motor Response* Motor Response* Motor Response* NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 16 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 17: Soft Stop Configuration
11.2 Turn Soft Stop ON Motor must be in fastest speed to turn Soft Stop ON. Press P2 Press UP Press UP Motor Response Motor Response Motor Response 17 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 18: Sleep Mode
Hold P1 button on the motor head Motor Response* Motor Response* Approx. NOTE: * ONLY THE PASSTHROUGH MOTOR BEEPS 18 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™... -
Page 19: Trouble Shooting
T +61 3 9355 0100 | F +61 3 9355 0110 T +39 02 8982 7317 | F +39 02 8982 7317 T +1 800 552 5100 | F +1 203 964 0513 19 | Automate Programming Instructions | Tilt Motors A Division of Rollease Acmeda ™...
Need help?
Do you have a question about the Automate MT01-4001 002 Series and is the answer not in the manual?
Questions and answers