Table of Contents
Advertisement
Quick Links
DCFT MOTOR
433 Mhz
Electronic
Bi-Directional
USE THIS DOCUMENT WITH THE FOLLOWING MOTORS:
PART NUMBER
MT01-1245-069001 AUTOMATE | DCFT 15 ARC Motor [Ø45/15Nm/10rpm]
AUTOMATE | DCFT tubular motors combine the simple, intuitive features of ARC "Automate Radio
Communication" with Fabric Tension capability and DC power. Three alternate modes of operation
include:
•
E-type for standard use
•
MANUAL FT Mode for use with conventional locking devices with fabric tensioning
•
AUTO FT Mode for use with Rollease Acmeda's proprietary ULTRA LOCK providing automatic
fabric tensioning
Functional options in each operating mode include: FAVORITE POSITION & BATTERY CHECK.
•
An intermediate setting allows for a customized FAVORITE POSITION to be preset.
•
The BATTERY CHECK feature lowers the shade to the level of charge remaining in the battery
pack when triggered.
•
IMPACT DETECTION senses an obstacle in the blinds path during downward movement and
redirects the shade to protect the motor, hardware and fabric, ensuring product longevity.
1 | Automate
Programming Instructions | DCFT Motors
™
Favorite
Limit
Position
DESCRIPTION
Fabric
Ultra
Tension
Lock
Battery
Impact
Check
Detection
A division of Rollease Acmeda
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for rollease acmeda AUTOMATE MT01-1245-069001
Summary of Contents for rollease acmeda AUTOMATE MT01-1245-069001
- Page 1 MANUAL FT Mode for use with conventional locking devices with fabric tensioning • AUTO FT Mode for use with Rollease Acmeda’s proprietary ULTRA LOCK providing automatic fabric tensioning Functional options in each operating mode include: FAVORITE POSITION & BATTERY CHECK.
- Page 2 - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 5005833 2 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™...
-
Page 3: Table Of Contents
9.2 Switching Auto & Manual Lock Modes 9.3 Auto Mode Operation 9.4 Manual Mode Operation 9.5 Activate/Deactivate FT Mode CONTROLLERS AND CHANNELS 10.1 Using motor P1 Button to add a new controller or channel ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 3 Automate ™... -
Page 4: Assembly + Installation Of Motor
ASSEMBLY + INSTALLATION OF MOTOR Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used. Drive tube Crown Drive Motor Cut roller tube to required length & Fit required crown, drive and Assemble tube with motor. -
Page 5: Wiring Routing
WIRING ROUTING Cassette Front Cover Ø14mm [9/16”] END PLATE HOLE Cassette End Plate Ø14mm [9/16”] END PLATE HOLE ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 5 Automate ™... -
Page 6: Selectable Mode
Inactive zone of 300 degrees x impact detection TUBE DIAMETER A 2 part drive adaptor, as used on the AC FT motor, is not compatible with the drive shaft. Bottom limit 6 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 7: P1 Button Functions
Hold P1 button on motor head. Activate Pairing Mode Approx. Sleep Mode P1 button on motor head. Approx. Approx. Reverse Direction Approx. Approx. Approx. Reset To Factory Settings Approx. Approx. Approx. Approx. ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 7 Automate ™... -
Page 8: Initial Set Up
Damage to shade may occur when operating motor prior to IMPORTANT setting limits. Attention should be given. Reversing motor direction using this method is only possible during initial set-up 8 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 9: Set Limits
UP or DOWN buttons To save lower limit, hold DOWN and STOP. on controller. Motor Response Approx. IMPORTANT After setting limits, motor will automatically exit from initial set-up mode. ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 9 Automate ™... -
Page 10: Adjusting Limits
When using the Ultra-lock V2, the bottom limit must be set within the ‘locking zone’. Jog the weight bar down until you hear both locking pins click into each housing. 10 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 11: Favorite Positioning
Motor Response Send shade to favorite position Approx. Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response ROLLEASE ACMEDA Automate Programming Instructions | DCFT Motor | 11 ™... -
Page 12: Fabric Tension Setting
Note: Motor must be in FT mode before switching between lock modes. Press P2 on controller. Press STOP on controller. Press DOWN on controller. AUTO MODE: Motor Response MANUAL MODE: Motor Response 12 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 13: Auto Mode Operation
Press DOWN on controller. Press UP on controller. Motor Response Motor Response Shade moves DOWN to release the Shade moves UP to the top limit. Locking device, then pauses. ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 13 Automate ™... -
Page 14: Activate/Deactivate Ft Mode
Impact Detection ON Motor Response Motor Response Motor Response Impact Detection OFF Motor Response IMPORTANT The top tube must be able to freely rotate ~ 5 degrees after installation. 14 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 15: Controllers And Channels
Press P2 on Press P2 on controller B to remove controller A. controller A. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor ROLLEASE ACMEDA Automate Programming Instructions | DCFT Motor | 15 ™... -
Page 16: Sleep Mode
Battery Charge Remaining Lower Limit Percentage Depleted Motor Response Shade must be at Upper Limit Shade moves to percentage of Hold UP for Approx. 5s battery charge remaining Approx. 16 | Automate Programming Instructions | DCFT Motor ROLLEASE ACMEDA ™... -
Page 17: Wind And Sun Sensor
The wind sensor function is ON by default. NOTE: Motor will jog to alert user if operated within 8 minutes. ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 17 Automate... -
Page 18: Trouble Shooting
Cannot program a single motor Multiple motors are paired to the Always reserve an individual (multiple motors respond) same channel channel for programming functions. Use Sleep Mode to program individual motors. 18 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™... -
Page 19: Notes
NOTES ROLLEASE ACMEDA Programming Instructions | DCFT Motor | 19 Automate ™... - Page 20 20 | Automate ROLLEASE ACMEDA Programming Instructions | DCFT Motor ™...
- Page 21 ROLLEASE ACMEDA | USA ROLLEASE ACMEDA | AUSTRALIA ROLLEASE ACMEDA | EUROPE Level 7 / 750 East Main Street 110 Northcorp Boulevard, Via Conca Del Naviglio 18, Stamford, CT 06902, USA Broadmeadows VIC 3047, AUS Milan (Lombardia) Italy T +1 800 552 5100 | F +1 203 964 0513...
Need help?
Do you have a question about the AUTOMATE MT01-1245-069001 and is the answer not in the manual?
Questions and answers