Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BioLAB PLATELET BINC-701
Summary of Contents for BioLAB PLATELET BINC-701
- Page 1 OPERATING MANUAL PLATELET INCUBATOR BINC-701 www.biolabscientific.com...
-
Page 2: Table Of Contents
INDEX I. Preface II. Safety Instruction 2.1 Prohibition 2.2 Warning 2.3 Cautions III. Installation Instruction 3.1 Installation Location 3.2 Installation Steps 3.3 Application IV. Operation Instruction 4.1 Structure 4.2 Temperature Controller V. Maintenance 5.1 Before Maintenance 5.2 Clean 5.3 Defrost 5.4 Battery Maintenance VI. -
Page 3: Preface
I. Preface Thank you for choosing and using our equipment. Please read this manual carefully before using the device and keep it properly for future reference. This manual contains important safety advice. Ignoring the following <Safety Instruction> may cause damage to the equipment and/or user injury. The user is responsible for any damages to the device caused by ignoring the requirements of this manual during use. -
Page 4: Safety Instruction
II. Safety Instruction 2.1 Prohibition Only authorized technicians are allowed to install, move, disassemble, and repair this device. Do not do these by yourself. Unauthorized personnel's improper operation may cause electric leakage, shock, personal injury, or fire. Do not install the device outdoors or in damp or splashing water areas. Exposure to rain and moisture will cause rust and reduce its electrical insulation properties, which may cause electric leakage, shock, and fire. - Page 5 Pull on the plug, not the power cord when unplugging the device. Or it may cause overheating and fire due to the internal damage of the power cord. Use the switch to turn the device on and off, not the plug. Plugging or unplugging the device while it works may cause a short circuit or electric shock.
-
Page 6: Warning
power cord. A damaged cord may cause electric shock or fire. Turn off and disconnect the power supply plug before repairing or maintaining the device to prevent electric shock or injuries. Do not touch the device when refrigerant leaks, and turn off the pipeline valves of flammable gas in the room promptly (If there are gas valves). -
Page 7: Cautions
castors or adjustable feet (if the device has them) and be careful not to tip over the device during movement to prevent damage or injury. ⚠️ Do not turn on the power for 1 hour after moving, which may cause a breakdown. ⚠️... - Page 8 ⚡ If the surrounding temperature is outside the optimum range (10°C~32°C), it may cause a breakdown. ⚡ This device has an alarm system. When the device breaks down, it will have audible and visual alarms. When first used, the alarm system will stop working for 3 to 8 hours (depending on the model number). ⚡...
-
Page 9: Installation Instruction
III. Installation Instruction 3.1 Installation Location This product is designed at 25℃ ambient temperature, a relative humidity of 80%, and is only able to work in a specified environment, or it will affect the refrigeration performance, even causing a breakdown. Exceeding this state may cause damage to the refrigeration system. Recommend Installation Locations: - Ambient temperature: 10 to 32°C - Relative humidity: Below 90%... -
Page 10: Operation Instruction
IV. Operation Instruction 4.1 Structure www.biolabscientific.com... -
Page 11: Temperature Controller
4.2 Temperature Controller 1. Mute Key Press Mute Key when the controller is alarming, the buzzing will stop for Mute times and the alarming code will remains during this period of time. If the error remains, the controller will buzzing again when it reaches Mute time. -
Page 12: Maintenance
If the time goes back to 2000 after power failure, please adjust time as following steps if controller hasn’t been used for a long time. - Press for 3S at the same time, screen will flickering. - Press again, choose a parameter you want to adjust(minute, hour, date, month, year) - Press to adjust the value. -
Page 13: Troubleshooting
VI. Troubleshooting Troubles Reasons and Solutions Is the socket powered? Is the power plug fully inserted in to the socket? The device does not cool down. Is the fuse or circuit breaker disconnected? Is there a power failure? Is the power switch turned off? Compressor breaks down Is the setting temperature correct? Temperature keeps decreasing after... - Page 14 Biolab Scientific Ltd. 3660 Midland Avenue, Suite 300, Toronto, Ontario M1V 0B8, Canada Email: info@biolabscientific.com | Website: www.biolabscientific.com...
Need help?
Do you have a question about the PLATELET BINC-701 and is the answer not in the manual?
Questions and answers