Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Digi Manuals
  4. Control Unit
  5. ConnectCore MP13
  6. Hardware reference manual

Digi ConnectCore MP13 Hardware Reference Manual

System-on-module
Hide thumbs Also See for ConnectCore MP13:

Advertisement

Quick Links

Download this manual
ConnectCore MP13
System-on-module
Hardware Reference Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the ConnectCore MP13 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Digi ConnectCore MP13

Summary of Contents for Digi ConnectCore MP13

  • Page 1 ConnectCore MP13 System-on-module Hardware Reference Manual...

  • Page 2: Trademarks And Copyright

    Added assembly instructions. Trademarks and copyright Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the property of their respective owners.

  • Page 3: Warranty

    Warranty To view product warranty information, go to the following website: www.digi.com/howtobuy/terms Customer support Gather support information: Before contacting Digi technical support for help, gather the following information:    Product name and model    Product serial number (s)    Firmware version    Operating system/browser (if applicable)    Logs (from time of reported issue)

  • Page 4: Table Of Contents

    Contents About the ConnectCore MP13 Features and functionality Safety instructions Limitations and notices GPIO Latch-up Block diagrams ConnectCore MP13 module STMicroelectronics STM32MP13x application processor Power interfaces System-on-module power architecture Reference power diagram Electrical characteristics Bootstrap Wireless interfaces WLAN IEEE 802.11a/b/g/n/ac...
  • Page 5 Operating frequency Europe and UK CE mark CE and UKCA OEM labeling requirements Declarations of Conformity Approved antennas Canada (IC) Canadian Notice Labeling requirements Transmitters with detachable antennas RF exposure Approved antennas Japan Approval Label (MIC Marking) ConnectCore MP13 System-on-Module...

  • Page 6: About The Connectcore Mp13

    Features and functionality About the ConnectCore MP13 The Digi ConnectCore® MP13 System-on-Module (SOM) platform is a highly integrated, cost- effective, connected, secure embedded solution, built on the STM32MP13x MPU family. It integrates memory, power management, pre-certified wireless connectivity and advanced Digi TrustFence device security with a complete, open-source Linux software platform based on the Yocto Project.

  • Page 7: Safety Instructions

    Limitations and notices GPIO The ConnectCore MP13 SoC has a limitation in the number of GPIOs that can be used as interrupt lines. The Extended Interrupt and Event Controller (EXTI) can only handle up to 16 GPIO lines working as interrupt (EXTI0..EXTI15). The multiplexers work as shown in the following figure:...

  • Page 8: Latch-Up

    Never hot-swap the module or interrupt its ground connection to external circuitry. When you use an external supply on the carrier board supporting the ConnectCore MP13 module, make sure this supply is NOT back driving STM32MP1 I/Os while their power rails are not enabled.

  • Page 9: Connectcore Mp13 Module

    About the ConnectCore MP13 Block diagrams ConnectCore MP13 module ConnectCore MP13 System-on-Module...

  • Page 10: Stmicroelectronics Stm32Mp13X Application Processor

    About the ConnectCore MP13 Block diagrams STMicroelectronics STM32MP13x application processor ConnectCore MP13 System-on-Module...

  • Page 11: Power Interfaces

    Power interfaces System-on-module power architecture The ConnectCore MP13 requires two primary power supply inputs: VSYS and VSYS2, which are the input power supplies to the on-module ST STPMIC1 power management IC (PMIC) that generates all required supply voltages for the module as well as the external interfaces.

  • Page 12: Reference Power Diagram

    Doing so could cause permanent damage to the device. Refer to Application note AN4879 from STMicroelectronics for further information. Reference power diagram The following diagram represents the power architecture of the ConnectCore MP13 module in a typical application: ConnectCore MP13 System-on-Module...

  • Page 13: Electrical Characteristics

    About the ConnectCore MP13 Power interfaces Electrical characteristics Input power rails The following table lists the electrical specifications of all input power rails for the ConnectCore MP13: Input voltage (V) Device SOM power rail Minimum Typical Maximum PMIC VSYS VSYS2...
  • Page 14 Output power rails The following table lists the electrical specifications of all output power rails for the ConnectCore MP13: Accuracy Turn-on time Turn-off time Output voltage (us) (ms) SOM power Used internally in the Continuous output current rail (mA) VDD_SD...

  • Page 15: Bootstrap

    Bootstrap Bootstrap The ConnectCore MP13 module can be configured to boot from different devices and interfaces as determined by the boot ROM. The configuration of the booting process of the CPU is done through the BOOT pin and OTP bytes.

  • Page 16: Wlan Ieee 802.11A/B/G/N/Ac

    The following sections specify the performance of the WLAN IEEE 802.11a/b/g/n/ac interface on the ConnectCore MP13 module. Modulation and data rates The following tables list modulation values for the ConnectCore MP13 module, which supports the following WLAN standards: Mode Modulation & coding Rate...
  • Page 17 About the ConnectCore MP13 Wireless interfaces Mode Modulation & coding Rate BPSK-1/2 MCS0 QPSK-1/2 MCS1 QPSK-3/4 MCS2 16QAM-1/2 MCS3 16QAM-3/4 MCS4 802.11ac 64QAM-2/3 MCS5 64QAM-3/4 MCS6 64QAM-5/6 MCS7 256QAM-3/4 MCS8 256QAM-5/6 MCS9 Data rate (Mbps) - Non Short Guard Interval (Non-SGI)

  • Page 18: Rf Channels

    72.2 HT40 HT80 32.5 433.3 RF channels The ConnectCore MP13 module supports the following frequency bands: Channel number (Center freq. MHz) band spacing 1(2412), 2(2417), 3(2422), 4(2427), 5(2432), 6(2437), 7(2442), 8 5 MHz (2447), 9(2452), 10(2457), 11(2462), 12(2467), 13(2472), 14(2484)
  • Page 19 About the ConnectCore MP13 Wireless interfaces 2.4 GHz NORTH EUROPE band Center frequency (MHz) AMERICA  JAPAN channel (ETSI) (FCC) 2422 ✔ ✔ ✔ 2427 ✔ ✔ ✔ 2432 ✔ ✔ ✔ 2437 ✔ ✔ ✔ 2442 ✔ ✔ ✔ 2447 ✔...

  • Page 20: Transmit Power

    DFS = Dynamic Frequency Selection TPC = Transmit Power Control SRD = Short Range Devices 25 mW max power Transmit power The following table lists nominal transmit power values for the ConnectCore MP13 module based on Murata LBEE5PK2AE-564 specification. ConnectCore MP13 System-on-Module...

  • Page 21: Antenna Ports

    802.11ac (VHT40) 14 (MCS0) - 11 (MCS9) 802.11ac (VHT80) 13 (MCS0) - 12 (MCS9) Antenna ports The ConnectCore MP13 module has one antenna port on the module via a dedicated U.FL connector. The antenna port supports WLAN and Bluetooth functionality. Bluetooth The ConnectCore MP13 module supports both Bluetooth and Bluetooth Low Energy protocols: Bluetooth 5 with all Bluetooth 4.2 optional features.

  • Page 22: Module Pinout

    External signals and pin multiplexing Module pinout The ConnectCore MP13 module has a mixed pad structure. The module provides 245 LGA pins, 76 of them connected to the peripheral castellated pads. The general layout can be found on the following diagram:...

  • Page 23: Digi Connectcore Smart Iomux Tool

    Digi ConnectCore Smart IOmux tool The Digi ConnectCore Smart IOmux tool can dramatically simplify pin configuration and resolution. You can enter the list of interfaces required by your project and use the Smart IOmux graphical interface to mock up configuration options, resulting in full pin assignment and device tree snippets that match your desired functionality.

  • Page 24: Castellated Pad Signals And Multiplexing

    Castellated pad signals and multiplexing ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments 1 / B1 CPAD1 VCC_LICELL VBAT VCC_ VCC_LICELL pin LICELL can be supplied by an external battery. If external battery is not used, then connect this pin to...
  • Page 25 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments 12 / N1 CPAD12 13 / P1 CPAD13 NRST NRST Reset line of the module. Add an external 10K resistor to VDD. 14 / R1 CPAD14 I2S1_WS...
  • Page 26 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments 16 / U1 CPAD16 SDMMC1_D1 AF0: TRACED1 VDD_SD AF2: TIM3_CH4 AF3: TIM8_CH4 AF7: USART3_RTS AF8: UART5_CTS AF9: FDCAN1_TX AF12: SDMMC1_D1 AF14: LCD_B4 17 / V1 CPAD17 SDMMC1_CMD...
  • Page 27 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: UART5_ RTS/UART5_DE AF12: SDMMC1_D0 AF14: LCD_G7 21 / AA3 CPAD21 SDMMC1_CLK PC12 AF0: TRACECLK VDD_SD AF8: UART7_TX AF10: SAI2_SD_B AF12: SDMMC1_CK AF14: LCD_DE 22 / AA4 CPAD22...
  • Page 28 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: ETH1_MII_ AF12: ETH2_MII_ 25 / AA7 CPAD25 UART5_RX PF13 AF1: TIM2_ETR ADC1_INP11 AF2: SAI1_MCLK_B ADC1_INN10 AF6: DFSDM1_ ADC2_INP11 ADC2_INN10 DATIN3 AF7: USART2_TX AF8: UART5_RX 26 / AA8 CPAD26...
  • Page 29 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF12: SAI2_SCK_A 31 / AA13 CPAD31 USB_OTG_ID PA10 AF1: TIM1_CH3 OTG_HS_ID 32 / AA14 CPAD32 I2S1_SDO AF1: TIM2_CH4 ADC1_INP12 AF2: TIM5_CH4 ADC1_INN11 AF3: LPTIM5_OUT PVD_IN AF4: TIM15_CH2...
  • Page 30 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF3: LPTIM4_OUT AF4: TIM15_CH1 AF7: USART2_TX AF11: ETH1_MDIO 39 / Y21 CPAD39 JTDO- JTDO- TRACESWO TRACESWO 40 / W21 CPAD40 JTCK-SWCLK JTCK-SWCLK 41 / V21 CPAD41 JTDI...
  • Page 31 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF13: DCMIPP_D1 AF14: LCD_B5 45 / P21 CPAD45 46 / N21 CPAD46 UART8_RTS PE14 AF1: TIM1_BKIN TAMP_IN6 AF4: SAI1_D4 AF8: UART8_ RTS/UART8_DE AF9: QUADSPI_ BK1_NCS AF10: QUADSPI_...
  • Page 32 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: ETH1_MII_ RXD0/ETH1_RGMII_ RXD0/ETH1_RMII_ RXD0 AF12: SAI2_D3 49 / K21 CPAD49 ETH1_RX_DV AF1: TIM1_CH1N ADC1_INP16 AF2: TIM3_CH2 AF3: TIM8_CH1N AF4: SAI2_D1 AF5: SPI1_ SCK/I2S1_CK AF7: USART1_ CTS/USART1_NSS...
  • Page 33 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments 52 / G21 CPAD52 ETH1_TX_EN PB11 AF1: TIM2_CH4 AF3: LPTIM1_OUT AF4: I2C5_SMBA AF7: USART3_RX AF11: ETH1_MII_ TX_EN/ETH1_ RGMII_TX_ CTL/ETH1_RMII_ TX_EN 53 / F21 CPAD53 ETH1_REF_CLK AF0: MCO1...
  • Page 34 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF6: SAI1_D4 AF7: USART2_ CTS/USART2_NSS AF9: SPDIFRX_IN3 AF11: ETH1_MII_ RXD1/ETH1_RGMII_ RXD1/ETH1_RMII_ RXD1 55 / D21 CPAD55 ETH1_TXD0 PG13 AF1: LPTIM1_OUT ADC2_INP6 AF7: USART6_ ADC2_INN2 CTS/USART6_NSS AF11: ETH1_MII_...
  • Page 35 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF14: DCMIPP_D12 58 / A20 CPAD58 LTDC_B6 AF1: TIM17_CH1N AF2: TIM1_CH1 AF3: DFSDM1_ CKIN3 AF6: SAI1_D4 AF7: UART7_CTS AF8: UART8_RX AF9: TIM14_CH1 AF10: QUADSPI_ BK1_IO1 AF11: QUADSPI_...
  • Page 36 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF5: SPI5_NSS AF7: USART6_ RTS/USART6_DE AF8: UART7_ RTS/UART7_DE AF9: QUADSPI_CLK AF13: DCMIPP_ HSYNC AF14: LCD_B5 62 / A16 CPAD62 LTDC_G2 PH13 AF0: TRACED15 AF2: USART2_CK AF3: TIM8_CH1N AF4: I2C5_SCL...
  • Page 37 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF7: LCD_B6 AF9: QUADSPI_ BK1_NCS AF11: ETH2_MDIO AF12: FMC_NE3 AF13: DCMIPP_D5 AF14: LCD_B7 AF15: HDP6 65 / A13 CPAD65 66 / A12 CPAD66 LTDC_B4 AF4: I2C3_SCL...
  • Page 38 ConnectCore Castellated ConnectCore MP13 signal STM32MP1 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF14: LCD_B3 69 / A9 CPAD69 LTDC_DE AF1: TIM1_CH4 AF2: TIM12_CH2 AF5: SPI4_ SCK/I2S4_CK AF6: DCMIPP_D13 AF9: LCD_B5 AF11: LCD_DE AF12: FMC_A20 AF13: DCMIPP_D9 AF14: DCMIPP_D8 70 / A8...

  • Page 39: Lga Pad Signals And Multiplexing

    LGA pad signals and multiplexing ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_A2 LGA_A3 LGA_A4 LGA_A5 LGA_A6 LGA_A7 LGA_A8 LGA_A9 LTDC_DE AF1: TIM1_CH4 AF2: TIM12_CH2 AF5: SPI4_SCK/I2S4_ AF12: FMC_A20 LGA_A10 LTDC_B3 PG15 AF7: USART6_...
  • Page 40 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF9: QUADSPI_BK2_ AF10: ETH1_MII_COL AF12: ETH2_MII_COL AF13: QUADSPI_BK1_ LGA_A13 LGA_A14 LTDC_B7 AF0: TRACED6 AF1: TIM16_CH1N AF2: TIM4_CH1 AF3: TIM8_CH1 AF4: USART1_TX AF6: SAI1_CK2 AF9: QUADSPI_BK1_ AF11: ETH2_MDIO AF12: FMC_NE3...
  • Page 41 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF8: UART4_TX LGA_A17 LTDC_B5 PF10 AF1: TIM16_BKIN TAMP_IN1 AF2: SAI1_D3 AF3: TIM8_BKIN AF5: SPI5_NSS AF7: USART6_ RTS/USART6_DE AF8: UART7_ RTS/UART7_DE AF9: QUADSPI_CLK LGA_A18 LTDC_B2 AF2: SAI2_FS_B AF5: I2C3_SDA...
  • Page 42 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: QUADSPI_BK2_ AF12: FMC_A9 LGA_A21 LGA_B1 VCC_LICELL VBAT VCC_LICELL pin can be supplied by an external battery. If external battery is not used, then connect this pin to VDD.
  • Page 43 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF12: FMC_A24 LGA_B5 LGA_B6 LGA_B7 RESERVED Reserved pad. LGA_B8 ETH2_TXD2 AF1: LPTIM1_ETR AF2: TIM4_ETR AF3: SAI2_FS_A AF4: I2C2_SMBA AF5: SPI2_ MISO/I2S2_SDI AF6: SAI2_D2 AF9: FDCAN2_TX AF10: ETH2_MII_ TXD2/ETH2_RGMII_...
  • Page 44 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF7: UART7_RX AF9: QUADSPI_BK1_ AF11: ETH2_MII_TX_ EN/ETH2_RGMII_TX_ CTL/ETH2_RMII_TX_ LGA_B11 ETH2_GTX_ AF3: TIM8_BKIN2 AF4: I2C2_SDA AF6: SAI2_SD_B AF9: FDCAN2_RX AF10: ETH2_RGMII_ GTX_CLK AF11: ETH1_MDIO AF12: FMC_A13 LGA_B12 LGA_B13...
  • Page 45 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_B20 LGA_B21 LTDC_HSYNC AF1: LPTIM1_IN2 AF8: UART8_TX AF12: FMC_NBL1 LGA_C1 VSYS VSYS Input power line. LGA_C2 VSYS VSYS Input power line. LGA_C3 LGA_C4 LGA_C5 LGA_C6 LGA_C7...
  • Page 46 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: ETH2_MII_RX_ DV/ETH2_RGMII_RX_ CTL/ETH2_RMII_ CRS_DV AF12: FMC_A7 LGA_C16 LPO_32K/PI1 AF8: SPDIFRX_IN1 RTC_ OUT2/RTC_ LSCO TAMP_ IN2/TAMP_ OUT3 WKUP4 LGA_C17 PCM_OUT Signal connected to the Wireless MAC.
  • Page 47 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_D1 LGA_D2 LGA_D3 LDO2 LDO2 Output power line. LGA_D4 LDO6 LDO6 Output power line. LGA_D5 LGA_D6 LGA_D7 LGA_D8 LGA_D9 LDO3 LDO3 Output power line. LGA_D10 LGA_D11 ETH2_REF_...
  • Page 48 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_D13 3V3_RF_ AF1: TIM17_CH1N Signal only AF2: TIM4_CH2 EN/PB7 available in non- AF5: I2S4_CK wireless variants. AF6: I2C4_SDA AF10: FMC_NCE2 AF12: FMC_NL AF13: DCMIPP_D13 AF14: DCMIPP_ PIXCLK LGA_D14...
  • Page 49 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF12: FMC_A6 LGA_D18 BT_UART_RX AF0: TRACED9 Signal only AF2: TIM5_ETR available in non- AF3: USART2_RX wireless variants. AF4: I2C3_SDA AF12: FMC_A8 AF15: HDP2 LGA_D19 BT_UART_RTS AF1: TIM2_CH2...
  • Page 50 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_E2 WKUP AF1: TIM16_CH1N WKUP1 AF2: TIM4_CH3 AF3: TIM8_CH3 AF6: SAI1_SCK_B AF7: USART6_TX AF9: TIM13_CH1 AF10: QUADSPI_BK1_ LGA_E3 Output power line. Recommendation is not to use this pad externally.
  • Page 51 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_F1 F2  LGA_F2 LGA_F3 VSYS VSYS Input power line. LGA_F19 WL_HOST_ Signal connected WAKE to the Wireless MAC. LGA_F20 LGA_F21 ETH1_REF_ AF0: MCO1 This signal can’t be AF3: USART2_CK used as an output...
  • Page 52 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_G3 VSYS VSYS Input power line. LGA_G19 BT_REG_EN PD13 AF1: LPTIM2_ETR Signal only AF2: TIM4_CH2 available in non- AF3: TIM8_CH2 wireless variants. AF4: SAI1_CK1 AF6: SAI1_MCLK_A AF7: USART1_RX AF9: QUADSPI_BK1_...
  • Page 53 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_H20 BT_HOST_ Signal connected WAKE to the Wireless MAC. LGA_H21 ETH1_TXD1 PG14 AF1: LPTIM1_ETR AF6: SAI2_D1 AF7: USART6_TX AF10: SAI2_SD_A AF11: ETH1_MII_ TXD1/ETH1_RGMII_ TXD1/ETH1_RMII_ TXD1 LGA_J1...
  • Page 54 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments is not to use this pad externally. See Output power rails. LGA_K3 Output power line. Recommendation is not to use this pad externally. See Output power rails.
  • Page 55 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF5: SPI1_SCK/I2S1_ AF7: USART1_ CTS/USART1_NSS AF9: TIM14_CH1 AF11: ETH1_MII_RX_ DV/ETH1_RGMII_RX_ CTL/ETH1_RMII_ CRS_DV AF12: SAI2_SD_A LGA_L1 L2  LGA_L2 LGA_L3 VREF+ VREF+ LGA_L19 WLAN_SD_ AF0: TRACED3 47K pull-up on AF1: TIM17_BKIN module connected...
  • Page 56 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF8: SDMMC1_CKIN AF10: SDMMC2_D1 AF12: SAI2_FS_A LGA_L21 ETH1_RXD0 AF2: TIM3_ETR ADC1_INP4 AF3: DFSDM1_CKIN2 ADC2_INP4 AF4: SAI1_D3 AF5: I2S1_MCK AF8: UART5_ RTS/UART5_DE AF9: SPDIFRX_IN2 AF11: ETH1_MII_ RXD0/ETH1_RGMII_ RXD0/ETH1_RMII_...
  • Page 57 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF2: TIM12_CH1 to VDD. AF3: TIM8_CH2N Signal only AF4: USART1_TX available in non- AF10: SDMMC2_D0 wireless variants. AF11: SDMMC1_D4 LGA_M20 WLAN_SD_D3 AF0: TRACED14 47K pull-up on AF1: TIM16_BKIN module connected...
  • Page 58 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_N3 LGA_N19 SPI4_MOSI PE11 AF1: TIM1_CH2 AF2: USART2_ CTS/USART2_NSS AF4: SAI1_D2 AF5: SPI4_ MOSI/I2S4_SDO AF6: SAI1_FS_A AF7: USART6_CK AF10: ETH2_MII_TX_ AF11: ETH1_MII_TX_ AF12: FMC_D8/FMC_ LGA_N20 SPI4_MISO PE13...
  • Page 59 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_P1 NRST NRST Reset line of the module. Add an external 10K resistor to VDD. P2  LGA_P2 Output power line. Recommendation is not to use this pad externally.
  • Page 60 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: ETH1_PHY_ INTN AF12: ETH2_MII_RX_ DV/ETH2_RGMII_RX_ CTL/ETH2_RMII_ CRS_DV LGA_P21 LGA_R1 I2S1_WS AF2: TIM5_ETR ADC1_INP14 AF3: USART2_CK AF4: SAI1_SCK_B AF5: SPI1_NSS/I2S1_ AF6: DFSDM1_CKIN1 AF10: ETH1_PPS_ AF11: ETH2_PPS_ AF12: SAI1_SCK_A R2 ...
  • Page 61 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF1: TIM1_BKIN2 AF4: DFSDM1_CKIN3 AF8: USART3_RX AF10: SDMMC2_ D123DIR AF12: FMC_A14 AF15: HDP1 LGA_R20 USART3_TX AF3: USART2_TX AF5: I2S4_WS AF7: USART3_TX AF8: UART4_RX LGA_R21 UART8_RX AF8: UART8_RX...
  • Page 62 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF2: SAI2_MCLK_A AF3: TIM8_BKIN2 AF4: I2C4_SDA AF5: SPI5_MISO AF6: SAI2_CK1 AF7: USART1_CK AF8: SPI2_ MOSI/I2S2_SDO AF10: OTG_HS_SOF AF11: ETH2_MII_ RXD3/ETH2_RGMII_ RXD3 AF12: FMC_A21 LGA_T20 LGA_T21 UART8_TX...
  • Page 63 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF8: UART5_CTS AF9: FDCAN1_TX AF12: SDMMC1_D1 U2  LGA_U2 LGA_U3 LGA_U19 AF1: TIM2_CH1/TIM2_ ADC1_INP2 AF2: USART2_CK AF3: TIM8_CH1N AF4: SAI1_D1 AF5: SPI1_NSS/I2S1_ AF6: SAI1_SD_A AF10: ETH1_PPS_ AF11: ETH2_PPS_ LGA_U20...
  • Page 64 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF5: SPI3_NSS/I2S3_ AF6: SAI2_D1 AF7: USART3_RX AF12: SDMMC1_CMD LGA_V2 LGA_V3 BOOT0 BOOT0 10K pull-up resistor. LGA_V4 LGA_V5 ETH2_RXD0 AF3: USART2_RX AF11: ETH2_MII_ RXD0/ETH2_RGMII_ RXD0/ETH2_RMII_ RXD0 AF12: FMC_A4...
  • Page 65 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_V10 LGA_V11 LGA_V12 SPI4_SCK PE12 AF1: TIM1_CH3N AF5: SPI4_SCK/I2S4_ AF8: UART8_ RTS/UART8_DE AF12: FMC_D9/FMC_ AF15: HDP4 LGA_V13 LTDC_G7 PA15 AF0: TRACED5 AF1: TIM2_CH1 AF5: I2S4_MCK AF7: UART4_ RTS/UART4_DE...
  • Page 66 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_V15 ETH2_RXD2 AF2: TIM12_CH1 AF3: USART2_CK AF4: I2C5_SDA AF5: SPI2_SCK/I2S2_ AF9: QUADSPI_BK1_ AF10: ETH1_PHY_ INTN AF11: ETH1_MII_RX_ AF12: ETH2_MII_ RXD2/ETH2_RGMII_ RXD2 AF13: QUADSPI_BK1_ LGA_V16 LGA_V17 ETH1_CLK125...
  • Page 67 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF11: ETH1_RGMII_ GTX_CLK LGA_V19 AF9: FDCAN2_TX AF12: FMC_A10 LGA_V20 PA11 PA11 AF1: TIM1_CH4 AF3: I2C5_SCL AF5: SPI2_NSS/I2S2_ AF7: USART1_ CTS/USART1_NSS AF10: ETH2_MII_ RXD1/ETH2_RGMII_ RXD1/ETH2_RMII_ RXD1 AF11: ETH1_CLK...
  • Page 68 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments CTS/USART3_NSS AF8: SDMMC1_D4 AF15: HDP0 LGA_W3 SDMMC1_D6 AF0: TRACED2 AF2: TIM3_CH1 AF3: TIM8_CH1 AF4: DFSDM1_ DATIN0 AF5: I2S3_MCK AF7: USART6_TX AF8: SDMMC1_D6 AF9: SDMMC2_D0DIR AF10: SDMMC2_D6 AF12: FMC_A19 AF15: HDP2...
  • Page 69 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments external pull-up resistor is required. LGA_W9 LGA_W10 LTDC_R6 AF0: TRACED13 AF3: DFSDM1_ CKOUT AF7: USART3_CK AF10: SDMMC2_D4 AF12: FMC_A0 LGA_W11 LGA_W12 LGA_W13 ETH2_RX_ER PF11 AF1: USART2_TX ADC1_INP8...
  • Page 70 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF10: ETH2_MII_CRS AF11: ETH1_MII_CRS AF12: FMC_NE4 AF13: ETH2_RGMII_ CLK125 LGA_W16 LGA_W17 ETH1_RXD2 AF0: DBTRGI ADC1_INP9 AF1: TIM1_CH2N ADC1_INN5 AF2: TIM3_CH3 ADC2_INP9 AF3: TIM8_CH2N ADC2_INN5 AF4: USART1_RX AF5: I2S1_MCK...
  • Page 71 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF2: TIM3_CH4 ADC2_INP5 AF3: TIM8_CH3N AF5: SPI1_SCK/I2S1_ AF6: DFSDM1_ DATIN1 AF7: UART4_RX AF11: ETH1_MII_ RXD3/ETH1_RGMII_ RXD3 LGA_W20 ETH1_TXD3 AF2: SAI2_SCK_B AF3: TIM8_CH3 AF4: TIM15_CH1 AF8: UART4_RX AF10: ETH1_MII_ TXD3/ETH1_RGMII_...
  • Page 72 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_Y3 LGA_Y4 I2S1_MCK AF2: SAI1_SCK_A ADC1_INP0 AF4: SAI1_CK2 ADC1_INN1 AF5: I2S1_MCK ADC2_INP0 AF6: SPI1_ ADC2_INN1 TAMP_IN3 MOSI/I2S1_SDO AF7: USART1_TX LGA_Y5 LGA_Y6 LGA_Y7 I2C3_SCL AF1: TIM16_CH1 2.2K pull-up on AF2: TIM4_CH3...
  • Page 73 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_Y10 LGA_Y11 VBUS_OTG Output power line. LGA_Y12 LGA_Y13 I2C2_SCL AF0: TRACED1 AF4: I2C2_SCL AF6: DFSDM1_CKIN1 AF7: USART6_CK AF9: SDMMC2_D0DIR AF11: SDMMC1_ D0DIR AF12: FMC_A2 LGA_Y14 I2C2_SDA PF1: TRACED7...
  • Page 74 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments LGA_Y21 JTDO- JTDO- TRACESWO TRACESWO LGA_AA1 LGA_AA2 SDMMC1_D0 AF0: TRACED0 VDD_SD AF2: TIM3_CH3 AF3: TIM8_CH3 AF5: SPI3_ MISO/I2S3_SDI AF7: USART6_CK AF8: USART3_CTS AF10: SAI2_FS_B AF11: UART5_ RTS/UART5_DE AF12: SDMMC1_D0...
  • Page 75 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF8: UART5_RX AF10: SAI2_SCK_B AF12: SDMMC1_D3 LGA_AA6 UART5_TX AF1: TIM2_CH1 ADC1_INP7 AF2: TIM5_CH1 ADC1_INN3 AF3: TIM8_ETR ADC2_INP7 AF4: TIM15_BKIN ADC2_INN3 AF6: SAI1_SD_B AF8: UART5_TX AF11: ETH1_MII_CRS AF12: ETH2_MII_CRS LGA_AA7...
  • Page 76 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AF4: SAI2_CK2 AF5: SPI1_ MISO/I2S1_SDI AF7: USART1_CK AF8: UART4_ RTS/UART4_DE AF9: TIM13_CH1 AF12: SAI2_SCK_A AA13 LGA_AA13 USB_OTG_ID PA10 AF1: TIM1_CH3 OTG_HS_ID AA14 LGA_AA14 I2S1_SDO AF1: TIM2_CH4 ADC1_INP12...
  • Page 77 ConnectCore ConnectCore MP13 signal STM32MP135 Additional Power MP13 pad name pad name Alternate functions functions group Comments AA20 LGA_AA20 ETH1_MDIO AF1: TIM2_CH3 ADC1_INP1 AF2: TIM5_CH3 ADC2_INP1 AF3: LPTIM4_OUT AF4: TIM15_CH1 AF7: USART2_TX AF11: ETH1_MDIO AA21 LGA_AA21...

  • Page 78: Module Specifications

    Module specifications External signals and pin multiplexing Module specifications The following sections describe the specifications for the ConnectCore MP13 SOM. Power consumption Mechanical specifications Environmental specifications Socket options ConnectCore MP13 System-on-Module...

  • Page 79: Power Consumption

    Power consumption Power consumption This section contains information about the power consumption of the ConnectCore MP13 system- on-module. All presented results, unless otherwise noted, were measured with ConnectCore MP13 variant -03 on a ConnectCore MP1 DVK at ambient temperature (25ºC).

  • Page 80: Power Consumption Use Cases

    Module specifications Mechanical specifications Power consumption use cases The power consumption of the ConnectCore MP13 system-on-module was evaluated in the following use cases: Standby In this mode, the system suspends to RAM and operation can be resumed without performing a new boot cycle.

  • Page 81: Label

    Label The MAC address and serial number of the SOM are encoded in the data matrix on the SOM label. Note See the ConnectCore MP13 product page for mechanical design documents, drawings, and other resources. Environmental specifications Operating temperature: -40 to 85 C.

  • Page 82: Socket Options

    Module specifications Socket options Socket options For testing, prototyping, and other primarily development-related purposes, Digi International and E-tec Interconnect AG have developed sockets allowing the easy insertion and removal of modules in a carrier board design. All drawings, user instructions, schematics and PCB footprints are posted on the ConnectCore MP13 technical support website.
  • Page 83 Assembly instructions Moisture sensitivity and shelf life Mounting Coplanarity Solder paste print Stencil SMT pick and place SMT process parameter reference - castellation and LGA applications Reflow oven profile Conformal coating ConnectCore MP13 System-on-Module...

  • Page 84: Moisture Sensitivity And Shelf Life

    10 trays. Mounting The ConnectCore MP13 has been designed with easy integration into existing SMT processes in mind. This section contains guidance for mounting the module on your carrier board. The module can be configured and mounted in a Castellation OR Land Grid Array (LGA) form.

  • Page 85: Smt Pick And Place

    Keep SoM below 238°C during the reflow cycle for castellation AND LGA applications. Time Above Liquidous (TAL) is recommended to be between 50 to 70 seconds. Use of 40AWG K-type thermocouple and M.O.L.E or equivalent thermal profiler is recommended. ConnectCore MP13 System-on-Module...
  • Page 86 Digi recommends X-ray analysis after reflow to confirm proper mounting and solder reflow. The ConnectCore MP13 is approved to withstand a total of four (4) reflow cycles. Two (2) reflow cycles are required for manufacturing the ConnectCore MP13. Two (2) reflow cycles are remaining for mounting the module on the carrier board.

  • Page 87: Conformal Coating

    Conformal coating Conformal coating ConnectCore MP13 variants without thermal putty may be conformally coated using an IPC-CC- 830 compliant Acrylic (Type AR) coating material. The material shall be applied by spray application per IPC-A-610. DIP coating method shall not be used. If other coating material is required Urethane (Type UR), Silicone (Type SR) or Epoxy (Type ER) please contact Digi.

  • Page 88: Regulatory Information And Certifications

    Regulatory information and certifications Note The ConnectCore MP13 module complies with Part 15 of the United States FCC rules and regulations. United States FCC Europe and UK Canada (IC) Japan ConnectCore MP13 System-on-Module...

  • Page 89: United States Fcc

    United States FCC United States FCC The ConnectCore MP13 module complies with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required. To fulfill FCC Certification, the OEM must comply with the following regulations: The system integrator must ensure that the text on top side of the module is placed on the outside of the final product.

  • Page 90: Fcc Notices

    155(5775) FCC notices IMPORTANT: The ConnectCore MP13 module has been certified by the FCC for use with other products without any further certification (as per FCC section 2.1091). Modifications not expressly approved by Digi could void the user's authority to operate the equipment.
  • Page 91 Regulatory information and certifications United States FCC Antenna used to certify the ConnectCore MP13 wireless module Peak Antenna Freq. antenna Directional Type Supplier Antenna part no. (MHz) gain (dBi) gain (dBi) Dipole Linx Technologies ANT-DB1-RAF-RPS 2402- 5.51 Inc. 2480 5150- 7.61...
  • Page 92 8.11 5725 5725- 8.11 5850 KYOCERA W3P35x8W04- 2402- U100D3B0A 2480 5150- 5250 5250- 5350 5470- 5725 5725- 5850 TAOGLAS FXP830.07.0100C * 2402- 3.32 6.33 2480 5150- 7.71 5250 5250- 7.71 5350 5470- 7.71 5725 5725- 7.71 5850 ConnectCore MP13 System-on-Module...

  • Page 93: Rf Exposure

    CAUTION statement in OEM product manuals in order to alert users of FCC RF Exposure compliance. Operating frequency 802.11 b/g/n: 2412-2462 MHz 802.11 a/n/ac : 5150-5250 MHz; 5250-5350 MHz; 5470-5725MHz; 5725-5850 MHz Bluetooth : 2402-2480 MHz ConnectCore MP13 System-on-Module...

  • Page 94: Europe And Uk

    5.500 to 5.700 GHz, 8 channels (excludes 5.600 to 5.640 GHz) CE mark The ConnectCore MP13 module is certified for use in several European countries. For information, visit www.digi.com/resources/certifications. If the ConnectCore MP13 module is incorporated into a product, the manufacturer must ensure compliance of the final product with articles 3.1a and 3.1b of the RE Directive (Radio Equipment...

  • Page 95: Declarations Of Conformity

    Important note Digi customers assume full responsibility for learning and meeting the required guidelines for each country in their distribution market. Refer to the radio regulatory agency in the desired countries of operation for more information.

  • Page 96: Approved Antennas

    Europe and UK Approved antennas The same antennas have been approved for Europe as stated in the FCC table for use with the ConnectCore MP13 module. Country list Note This device is restricted to indoor use only when operating in the 5150-5350MHz frequency range within all member states.

  • Page 97: Canada (Ic)

    Regulatory information and certifications Canada (IC) Canada (IC) IC: 1846A-CCMP1 PMN: ConnectCore MP13 HVIN: 55002163-XX Canadian Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.

  • Page 98: Rf Exposure

    The ConnectCore MP13 module is for professional (OEM) installation only. Le module ConnectCore MP13 doit impérativement être installé par un professionnel (OEM). RF exposure To satisfy Industry Canada RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.

  • Page 99: Approval Label (Mic Marking)

    Label text Note Due to space constraints, the ConnectCore MP13 module label doesn’t support radio marking for Japan. If space allows, end product label should support radio marking for Japan. If not, radio marking shall be documented in the user manual.
  • Page 100 Regulatory information and certifications Japan If the device is too small it can be displayed on the user manual and on the packaging or container. ConnectCore MP13 System-on-Module...