Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vintage Air 473157
Summary of Contents for Vintage Air 473157
-
Page 1: Cover
1957 Chevrolet Chrome Finish Control Panel Kit (473157) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com 903292 REV B 10/09/24, PG 1 OF 10... -
Page 2: Table Of Contents
Table of Contents www.vintageair.com Cover..........................Table of Contents......................... Packing List/Parts Disclaimer....................Control Panel Installation....................... Control Panel Calibration Procedure..................Control Panel Calibration Procedure (Cont.)................Gen IV Wiring Diagram......................Gen 5 Wiring Diagram......................Operation of Controls......................Packing List........................903292 REV B 10/09/24, PG 2 OF 10... -
Page 3: Packing List/Parts Disclaimer
Screw, #8 x 3/4”, Oval Head ** Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items. -
Page 4: Control Panel Installation
Wire according to the wiring diagram on Page 5 for Gen IV systems or Page 6 for Gen 5 systems. Control Panel NOTE: When using a Vintage Air supplied control panel, connect the TAN 20 AWG wire from the Gen IV evaporator wiring harness... -
Page 5: Control Panel Calibration Procedure
Control Panel Calibration Procedure www.vintageair.com On Vintage Air Gen IV and Gen 5 systems using cable converters or replacement electronic controls, it is necessary to calibrate the system to your specific control panel. This procedure ensures that the travel of your control panel levers or knobs is translated into precise control of the blower speed, temperature blend and mode door position. -
Page 6: Control Panel Calibration Procedure (Cont.)
Control Panel Calibration Procedure (Cont.) www.vintageair.com 1. Turn on the ignition switch (Do not start the engine). 2. Move the control levers/knobs to the positions shown. 3. Connect the white jumper wire to the gray program wire. Wait approximately 5 seconds for the blower speed to change if using a Gen IV system, if using a Gen 5 system wait for the blower to default to medium speed. -
Page 7: Gen Iv Wiring Diagram
Gen IV Wiring Diagram www.vintageair.com 232007-VUR AC ANNUNCIATOR BACKLIGHT POS BACKLIGHT NEG 5V-SW WHT/RED TEMP WIPER WHT/YEL MODE WIPER WHT/GRN FAN WIPER PRE-WIRED VIEWED FROM WIRE SIDE GEN IV ECU 232002-VUA (IF USED) TEMP MODE PROGRAM * DASH LAMP (IF USED) *** WIDE OPEN THROTTLE SWITCH... -
Page 8: Gen 5 Wiring Diagram
Gen 5 Wiring Diagram www.vintageair.com 232007-VUR AC ANNUNCIATOR BACKLIGHT POS BACKLIGHT NEG 5V-SW WHT/RED TEMP WIPER WHT/YEL MODE WIPER WHT/GRN FAN WIPER PRE-WIRED VIEWED FROM WIRE SIDE GEN 5 ECU 232002-VUA (IF USED) TEMP MODE PROGRAM DASH LAMP * (IF USED) PINK WIDE OPEN ** THROTTLE... -
Page 9: Operation Of Controls
Operation of Controls www.vintageair.com On Gen IV or Gen 5 systems with three lever/knob controls, the temperature control toggles between heat and A/C operations. To activate A/C, move the temperature lever/knob all the way to cold and then back it off to the desired vent temperature. -
Page 10: Packing List
Packing List: Control Panel Kit (473157) www.vintageair.com Qty. Part No. Description 493057 Control Panel 232007-VUR Control Harness, Gen IV/Gen 5 Universal 643257 Bracket, Control Panel Mounting 189801 U-nut, #8 182467 Screw, #8 x 3/4”, Oval Head Checked By: Packed By: Date: NOTE: Images may not depict actual parts and quantities.
Need help?
Do you have a question about the 473157 and is the answer not in the manual?
Questions and answers