olympia electronics SLL-1001/WP/WL Manual

NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained operation (*)
A: Including test device
B: Including remote test mode
C: Including inhibiting mode
E: With non-replacable lamp(s) and/or battery
F: Automatic test gear complying with IEC 61347-2-7 denoted EL-T
90: 1.5 hour duration
180: 3 hours duration
(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
Non Maintained operation: The luminaire lights its illumination source, only in mains power supply's failure.
X 1
ATTENTION!!!
The light source of this luminaire is not replaceable when the light source reaches its end of life the
whole luminaire shall be replaced.
CAUTION : Do not view directly with bare eyes.
Technical Characteristics
SLL-1001/WP/WL
220-240V AC / 50-60Hz
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
SUPPLY CURRENT
U-OUT
Prated
Irated
MAX OPEN CIRCUIT VOLTAGE
WIRE CROSS SECTION 0.5mm - 2.5mm
MINIMUM POWER FACTOR
4.8V/3Ah
BATTERY (Ni-Cd)
Tx/Rx FREQUENCY RANGE
Tx POWER
INSULATION BETWEEN SUPPLY & CONTROL TERMINALS Basic insulation
INSULATION BETWEEN SUPPLY & BATTERY CIRCUIT Basic insulation
BATTERY PROTECTION Deep discharge and overcharge protection / the control gear will recharge the battery normally after the test of 22.3
MIN MAX. DISCHARGE VOLTAGE
MIN MAX. DISCHARGE CURRENT
MIN MAX. CHARGE CURRENT
TRICKLE CHARGE VOLTAGE/CURRENT
MAX CHARGE VOLTAGE
INDICATIONS LED Charge, Lamp Fault LED, Battery Fault LED
CHARGE TIME
MINIMUM DURATION 1.5 hour
LIGHT SOURCE
LIGHT SOURCE LUMINOUS FLUX (MAINS / EMERGENCY) 700lm / 1000lm
DEGREES OF COVER PROTECTION
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2,
PRODUCED IN ACCORDANCE WITH
ΕΝ 61000-3-3, ETSI EN 303 446-1 v1.1.0, ETSI EN 300 220-2 v3.1.1
OPERATION TEMPERATURE RANGE
CONTROL GEAR MAX.TEMPERATURE: tc
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION (L x W x H) 322 x 162 x 58 mm
WEIGHT 1041gr.
GUARANTEE 3 years (1 year for the battery)
CONTROL GEAR WITH AUTOMATIC
TEST FUNCTION
LED Characteristics
SLL-1001/WP/WL
MANUFACTURER Olympia Electronics S.A.
MODEL NUMBER
VOLTAGE RANGE
NOMINAL POWER
CONNECTIONS Fixed connection between main pcb and led module
TEMPERATURE (tc) 65 °C max. across the board
4
Warranty
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty is
specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which accompanies
each product. This warranty ceases to exist if the buyer does not follow the technical instructions included in
official documents given by Olympia Electronics or if the buyer modifies the goods provided or has any repairs
or re-setting done by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that
have been damaged can be returned to the premises of our company for repair or replacement, as long as the
warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the buyer
depending on the reason of defection. Olympia Electronics reserves the right to charge or not the buyer the
transportation cost.
A B C E F 1 8 0
SLL-1003/WP/WL
11W / 11.4VA
52mA
23V
5.3W
375mA
23V
2 2
0.94
4.8V/6Ah
868-870MHz
11dBm
4 - 6V
1000 - 1350mA
360 - 410mA
5.7V / 40mA
6V
24 hours
3 hours
30 white LEDs
IP65
o
5 to 40 C
o
74 C at Z3
Up to 95%
ABS/PC, PC
1317gr.
SLL-1003/WP/WL
1603195
13.3-14.3V DC
5.3W
5
923100305_09_002
Warranty
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
info@olympia-electronics.gr
923100305_09_002
European
manufacturers
SLL-1001/WP/WL & SLL-1003/WP/WL
WATERPROOF SELFTESTING
MAINTAINED/NON MAINTAINED
EMERGENCY LUMINAIRES
WITH WIRELESS COMMUNICATION
Μ NM
Duration Duration Light output
Non
IP65
Maintained 1.5h 3h 1000lm
maintained Wireless
Thank you for your trust in our products
Olympia Electronics - European manufacturer