Advertisement
Quick Links
1. What's in the Box
2. Overview
3. Preparing Your S1 Pro
3.1 Remove Stickers and Foam Packaging
3.2 Install Side Brushes
3.3 Connect to Power Supply
3.4 Place the Station
3.5 Install Hard Floor Cleaner
3.6 Add Clean Water
3.7 Turn On the Robot
3.8 Download the eufy Clean App
3.9 Set Up the Wi-Fi Connection
3.10 Place the Robot
4. Using Your S1 Pro
4.1. Important Tips Before Use
4.2. Mapping
4.3. Start Cleaning
4.4. End a Cleaning Task
4.5. Enable Dust Collection
4.6 Dry the Mop
5. More Features
5.1 Multi-Floor Cleaning
5.2 Smart Speaker Connection
5.3 Firmware Update
5.4 Ozone Water Preparation
5.5 Automatic Water Drainage
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EUFY S1 Pro
Summary of Contents for EUFY S1 Pro
- Page 1 1. What's in the Box 2. Overview 3. Preparing Your S1 Pro 3.1 Remove Stickers and Foam Packaging 3.2 Install Side Brushes 3.3 Connect to Power Supply 3.4 Place the Station 3.5 Install Hard Floor Cleaner 3.6 Add Clean Water 3.7 Turn On the Robot...
- Page 2 6. Cleaning and Maintenance 6.1 Maintenance Frequency 6.2 Clean the Parts 6.2.1 Clean the Dirty Water Reservoir 6.2.2 Clean the Dust Bin and Filters 6.2.3 Replace the Rolling Mop 6.2.4 Clean the Swivel Wheel 6.2.5 Clean the Side Brushes 6.2.6 Clean the Rolling Brush 6.2.7 Clean the Sensors and Charging Contact Pins 6.2.8 Clean the Wheels 6.2.9 Clean the Dirty Water Tank...
- Page 3 1. What's in the Box Robot Uniclean™ Station (with Dust Bag Included) Side Brushes (Two Sets) Power Cord Additional High-Performance Additional Rolling Mop Filter Cleaning Tool Additional Dust Bag Hard Floor Cleaner (600 ml) Quick Start Guide and Other Documents...
- Page 4 2. Overview Exterior ❶ 3D MATRIX EYE™ Sensor ❷ TrueAI Sensor ❸ Bumper ❹ ❹ ❺ Recharge Button ❸ ❻ • Press to pause cleaning, then press again to return Robot to the station ❺ ❷ Start / Pause Button •...
- Page 5 Bottom ❶ ❺ ❻ ❼ Rolling Mop ❷ ❹ Wheels (×2) ❸ ❸ ❹ Brush Guard ❷ ❹ Side Brushes (×2) ❶ ❷ ❺ Rolling Brush ❻ Swivel Wheel ❼ Carpet Detection Sensor Dirty Water Reservoir ❹ ❸ ❶ Robot Water Sink Filter ❷...
- Page 6 Uniclean™ Station ❶ ❺ Clean Water Tank ❷ ❷ ❹ Water Inlet ❸ Dirty Water Tank ❹ ❻ Dirty Water Tank Cover ❸ ❶ ❺ LCD Screen ❻ Hard Floor Cleaner ❼ Filter Tray ❽ Automatic Water Filling ❿ Interface ⓬...
- Page 7 3. Preparing Your S1 Pro 3.1 Remove Stickers and Foam Packaging Before using, remove stickers and foam packaging from the robot and Uniclean™ Station. • The foam packaging comes with an additional rolling mop inside.
- Page 8 3.2 Install Side Brushes Make sure the brushes marked 1 (red) and 2 (gray) are correctly installed based on the diagram below. You will hear a "click" when the side brushes are in place. 3.3 Connect to Power Supply Remove the cord cover and firmly insert the power cord as shown in the diagram. Tuck any excess cable into the winding groove, then reinstall the cover.
- Page 9 Follow the diagram to remove the clean water tank. Peel o the sticker from the station, then insert the cartridge into the cleaner slot. You will hear a "click" when the floor cleaner is securely installed. • Only use floor cleaner specified by eufy. Using other cleaners may damage the product, and will not be covered by the warranty.
- Page 10 3.8 Download the eufy Clean App To enjoy all the available features, it is recommended to control your robot via the eufy Clean app. You can try the following methods: 1. Download the eufy Clean app from the App Store (iOS devices) or Google Play (Android devices), or by clicking this link: https://dl-eufy.eufylife.com/qcdl/index.html?flow=eufy.
- Page 11 Enable Bluetooth on your mobile phone, tap "Add Device" on the main screen of the app, and select S1 Pro from the device list. After the device appears on the list, tap "Add" to start connecting to the robot.
- Page 12 • If your router uses WPA3 encryption, switch to WPA2. Upon successful connection, you can customize the robot's name, select cleaning modes, adjust settings, edit maps, and schedule cleanings. 3.10 Place the Robot Attach the robot to the by aligning the charging contact pins. Once the robot successfully docks with the station, it will automatically start charging and sound a voice prompt.
- Page 13 20 mm C. It is strongly recommended to place physical barriers or set a "No-Go Zone" / "Virtual Wall" via the eufy Clean app in front of fireplaces and certain areas (i.e. air vents) that may cause damage to the robot if entered.
- Page 14 4.2. Mapping Before using your robot for the first time, create a map of the new environment to start cleaning tasks. To start mapping, tap the on the LCD screen of the station or tap "Mapping" in the app. • Ensure all interior doors are open and remove obstacles like power cords on the ground for a complete map.
- Page 15 • To improve mopping performance, it's recommended to use the Vacuum Only mode 1-3 times before switching to Mop mode in a new environment. 4.3.2 Start a Cleaning Task You can start a cleaning task by ： • Tapping the on the LCD screen of the base station.
- Page 16 4.5. Enable Dust Collection The robot will automatically initiate dust collection at the base station after cleaning more than 45 square meters. • Mid-cleaning dust collection: If "Auto Empty by Cleaning Area" is selected in the "Base Station Settings" of the app, the robot will periodically return to the station for dust collection at the pre-set frequency during the cleaning process, and then continue cleaning after dust collection is complete.
- Page 17 4.6 Dry the Mop After mopping, the robot will automatically dry the mop. • Drying mode: You can switch the drying mode through the "Base Station Settings" in the app. Standard Dry is suitable for most households, while Quick Dry is suitable for areas with a dry climate. •...
- Page 18 • To mop across floors, ensure the robot completes a mop washing task before moving it to a di erent floor for cleaning. 5.2 Smart Speaker Connection S1 Pro can connect to your home's smart speaker for voice-controlled cleaning tasks. It currently supports Amazon Alexa and Google Home Speaker. 5.3 Firmware Update Whenever a new firmware is available, you can update in the following ways:...
- Page 19 • Empty any remaining water from the robot's dirty water reservoir and the dirty water tank of the station. • Remove the floor cleaner and mop, then store them properly. 6. Cleaning and Maintenance 6.1 Maintenance Frequency To ensure optimal performance of S1 Pro, we recommend regular maintenance of its components. Module Components Cleaning Frequency...
- Page 20 6.2 Clean the Parts 6.2.1 Clean the Dirty Water Reservoir ❶ Remove the robot's magnetic cover. Press the release buttons on both sides of the dirty water reservoir, and pull it out. ❷ Take out the water sink and sink filter. ❸...
- Page 21 6.2.2.2 Filters ❶ Press the release latch to open the top cover of the dust bin. ❷ Take out the high-performance filter. ❸ Use the provided cleaning tool to clean the high-performance filter and the pre-filter. If the high-performance filter cannot be cleaned thoroughly, replace it with a new one. •...
- Page 22 6.2.3 Replace the Rolling Mop ❶ With the robot powered on, remove the magnetic cover and take out the dirty water reservoir, then the rolling mop will automatically descend. ❷ Flip the robot over, press the rolling mop release button. ❸...
- Page 23 6.2.5 Clean the Side Brushes ❶ Grap the side brushes with both hands and pull them out. If the brushes are entangled with hair, clean them manually. ❷ Reinstall the red side brush into the red slot, press it down until you hear a click. Reinstall the grey side brush in the same manner.
- Page 24 6.2.7 Clean the Sensors and Charging Contact Pins Wipe the 3D MATRIX EYE™ Sensor, wall sensors, charging contact pins, cli sensors, and carpet detection sensor with a damp cloth. • Clean these sensors regularly to prevent slipping, charging issues, or abnormal carpet detection. 6.2.8 Clean the Wheels Wipe the dirt o the robot's wheels with a damp cloth.
- Page 25 6.2.9 Clean the Dirty Water Tank ❶ Remove the dirty water tank. ❷ Open and empty the dirty water tank. ❸ Rinse the dirty water tank thoroughly with water. ❹ Reinstall the dirty water tank into the station. An animation will display on the LCD screen when the dirty water tank is properly installed.
- Page 26 • Robot is powered • Open the robot's magnetic cover and eufy Clean app check if the power switch is in the indicates that the • Robot "O" position. If so, switch it to the "I"...
- Page 27 Module Problems Possible Causes Solutions • Robot is entangled by power cords or • Check if the robot is trapped or stuck other objects. on obstacles, and inspect if the side • Rolling brush brushes, rolling brush, wheels, or rolling or side brush is Robot is stuck and mop are tangled with other objects.
- Page 28 Module Problems Possible Causes Solutions • Swivel wheel slipping due to dirt. • Remove the swivel wheel, clean it, and • There are many then reinstall it onto the robot. obstacles in the Robot's cleaning • Before the robot starts cleaning, robot's cleaning path is disorganized, please try to tidy up the scattered...
- Page 29 Module Problems Possible Causes Solutions • Clean any foreign objects or hair • Wheels entangled wrapped around the wheels. Robot unable to with debris or hair. • Disassemble the wheels to check if the move, spining in one • The spring of spring is secure or broken.
- Page 30 Module Problems Possible Causes Solutions • Check if the dust bag is properly in • The dust bag is not place. Dust bag leakage properly in place. • Remove any debris from the dust bag from the station. • The dust bag is full. installation slot, then replace the dust bag.
- Page 31 8. Specs Dimensions 347*325*96mm Weight 4.78kg Battery 4600mAh,21.6v 25V ⎓ 1.5A Input Power Rated Power Max 61.7W Consumption Vacuum-Only Mode: Up to 277 minutes Cleaning Time Vacuum and Mop Mode: Up to 184 minutes Charging Time 3.6h (15%-100%) 5-40 ℃ Charging Temperature Dimensions...
- Page 32 (JP) +81 03 4455 7823 (CN) +86 400 0550 036 For video tutorials, FAQs, warranty policies, and more information, please visit: https://support.eufy.com/ Hereby, Anker Innovations Limited declares that this device is in compliance with The Product Security and Telecommunications Infrastructure (Security Requirements for Relevant Connectable Products) Regulations 2023.
Need help?
Do you have a question about the S1 Pro and is the answer not in the manual?
Questions and answers