Advertisement
Quick Links
Advertisement
Related Manuals for Memmert CPM650
Summary of Contents for Memmert CPM650
- Page 1 Additional equipment CPM650 Pumping device CPM650 www.memmert.com...
- Page 2 Table of Contents Table of Contents 1. About this Manual 2. Safety 2.1 Terms and Symbols Used ............................2.1.1 Terms Used..............................2.1.2 Symbols Used .............................. 2.2 Product Safety and Dangers............................2.3 Requirements to be met by Operating Personnel......................2.4 Responsibility of the Owner ............................2.5 Applied Directives and Standards..........................
- Page 3 Table of Contents 5.2 Connecting the Unit to the Power Supply ........................17 5.3 Filling the Waterbath ..............................17 6. Operation and Control 6.1 Switching the Unit on..............................18 6.2 Function Test................................18 6.3 Dismantling the Hoses ............................. 19 7. Malfunctions, Warning and Error Messages 8.
- Page 4 ■ Service manual: To carry out service and repair work you will require the separate service manual. Manuals can be requested from Memmert International After Sales or downloaded from www.memmert.com. Retaining and passing on this manual This operating manual belongs to the unit and must always be kept in a location where it can be easily found by those working with the unit.
- Page 5 E-mail: sales@memmert.com www.memmert.com International After Sales Memmert GmbH + Co. KG Willi-Memmert-Straße 90-96 | D-91186 Büchenbach | Germany Tel. +49 9171 9792 911 E-mail: service@memmert.com www.memmert.com If you have any queries, please always quote the product number on the nameplate.
- Page 6 Safety Safety Terms and Symbols Used In this manual and on the unit itself, certain recurring terms and symbols are used to warn you of hazards or give you information that is important in order to prevent injury or damage. To avoid accidents and damage, observe and follow these instructions. These terms and symbols are explained below.
- Page 7 Safety DANGER Danger due to electric shock Penetration of liquid into the unit can cause electric shocks and short circuits. – Opening the electronics box is prohibited. – Protect the unit from splashing water. – Switch off the unit and disconnect the mains plug before cleaning and maintenance work.
- Page 8 Changes and Alterations The accessories may be used only in connection with a Memmert waterbath WTB. The accessories must not be converted or modified without permission. No parts may be added or installed which have not been approved by the manufacturer.
- Page 9 Safety Switching off the Unit in an Emergency WARNING Hot surfaces Depending on the operating situation, the unit and the load may be hot. Contact with hot surfaces may have serious health consequences due to burns! – Allow the unit to cool down. –...
- Page 10 Readjusting the temperature control The temperature control of the WTB waterbath is optimised for standing water. The temperature control may require readjustment when a CPM650 circulation pump is in operation, as flowing water has a higher heat transfer coefficient than standing water.
- Page 11 Product Use 3.3.1 Intended Use The Memmert circulation pump is intended exclusively for use with a Memmert waterbath WTB. It is used for the internal circulation of the tempering medium in the waterbath. 3.3.2 Use Not in Accordance with the Intended Purpose The circulation pump is used exclusively for internal circulation in the waterbath and is not intended for temperature control of external circuits.
- Page 12 2 Operating voltage 3 Degree of protection 4 CE conformity 5 Manufacturer's address 6 Information regarding disposal 7 Connection / power ratings 8 Unit number Technical Data Accessory CPM650 Dimensions Length Width Height Electrical data Displacement volume l/mm Operating voltage Power Current consumption 230 V/50 Hz...
- Page 13 Design and Description ■ Heavy dust production or aggressive vapours in the vicinity of the unit could lead to sedimentation in the interior and, as a consequence, could result in short circuits or damage to electrical parts. For this reason, sufficient measures to prevent large accumulations of dust or aggressive vapours should be taken.
- Page 14 Delivery, Transport and Set-up Delivery, Transport and Set-up Safety DANGER Risk of short circuit Condensation in the electrical components may cause short circuits. – After transporting or storing the unit in humid conditions, remove it from its packaging and allow it to acclimatise for at least 24 hours in normal ambient conditions. –...
- Page 15 Delivery, Transport and Set-up CAUTION Fire hazard The surfaces of the unit may overheat during operation and overheat heat-sensitive surfaces in close proximity to the unit. – Always place the unit on a heat-resistant, fireproof and non-flammable surface and – maintain the specified clearances around the unit. The distance between the wall and the rear of the unit must be at least 30 ...
- Page 16 Delivery, Transport and Set-up 4. Route the tube from the IN pump connection (suction line) to the waterbath. 5. Attach the tube to the long pipe connection. 6. Guide the tube from the OUT pump connection (pressure line) to the waterbath. 7.
- Page 17 Putting into Operation Putting into Operation Putting into Operation for the First Time NOTICE When putting the unit into operation for the first time, do not leave it unattended until it has reached a steady state. Connecting the Unit to the Power Supply Route the power cable so that nobody can trip over it ■...
- Page 18 Operation and Control Operation and Control WARNING Hot components During operation of the pumping device, individual components may heat up. Touching them can cause burns. – Use temperature-resistant protective gloves. NOTICE There must not be any coarse-grained particles in the waterbath. This could damage the pumping device.
- Page 19 Operation and Control Dismantling the Hoses WARNING Hot components During operation of the pumping device, individual components may heat up. Touching them can cause burns. – Use temperature-resistant protective gloves. 1. Allow the water in the waterbath and the hoses to cool down first. 2.
- Page 20 CPM cannot be switched off Main switch defective Disconnect the mains plug ■ ■ If the error persists, contact the service department: service@memmert.com Tempering medium circulates only slightly Water level too low Check water level ■ or not at all ■...
- Page 21 – For correct application, follow the instructions for use on the respective container of the decontamination agent. Memmert units can become contaminated by loading infectious substances or by environmental influences at the place of installation. All parts of the affected unit must be decontaminated both before sending to our service department and before disposing of the unit.
- Page 22 Cleaning and Decontamination After cleaning and decontamination, ventilate the installation site and allow the unit to dry completely. D57596 09/2023...
- Page 23 Repairs and Service Repairs and Service DANGER Danger due to electric shock Penetration of liquid into the unit can cause electric shocks and short circuits. – Protect the unit from splashing water. – Switch off the unit and disconnect the mains plug before carrying out any cleaning and maintenance work.
- Page 24 Additional equipment Pumping device D57596 Effective 09/2023 CPM650 English...
Need help?
Do you have a question about the CPM650 and is the answer not in the manual?
Questions and answers