Mackworth TX600 Advanced Setup Manual
Ceiling track lift
Hide thumbs
Also See for TX600 Advanced:
- User manual (38 pages) ,
- Manual (7 pages) ,
- Service manual (63 pages)
Related Manuals for Mackworth TX600 Advanced
Summary of Contents for Mackworth TX600 Advanced
- Page 1 TX Advanced Ceiling Track Lift Set Up Guide Doc No. 996674 Revision of document: A Revision Date: 13.04.2021...
- Page 2 Contents Introduction ................................3 Safety Precautions ..............................4 Required Tools and Equipment for Lift Set Up and Decommissioning ..........5 Lift Unboxing ..............................6 Lift Installation ..............................7 Ceiling Track Access ............................7 Installing the Charger ............................8 4.2.1 Installing Charging Dock Type 1 (Track Type 1) ..................8 4.2.2 Installing Charging Dock Type 2 (Track Type 2) ..................
- Page 3 Welcome to the Mackworth TX Advanced Ceiling Track Lift Commissioning and Decommissioning Manual, this manual includes the TX440 Advanced and the TX600 Advanced variants. Here it will explain on how to successfully install the lift into a pre- existing Ceiling Track safely and securely, as well as how to remove the lift from the Track. Use the contents page for easier navigation around the manual to discover the required section.
- Page 4 The lift is not intended to be used in environments where there are rapid changes in the environmental temperature and humidity during intended use. Any commissioning or decommissioning of the lift that has not been carried out by an authorized Mackworth personnel will void the product warranty.
- Page 5 2.1 Required Tools and Equipment for Lift Set Up and Decommissioning When carrying out work on the Ceiling Track Lift you will require the following: Tools Required 2mm T Bar Allen wrench 2.5mm T Bar Allen wrench 3mm T Bar Allen wrench 4mm T Bar Allen wrench 5mm T Bar Allen wrench 5.5mm combination spanner...
- Page 6 3.0 Lift Unboxing This section will summarize the layout of the Lift Packaging and what is included in the Box. It is recommended a small pocketknife is used for smoother unpacking of the lift. The lift is packed into a single box (11"x26.5"x14.5"), weighing approximately 24 lb (11 kg).
- Page 7 4.0 Lift Installation This section will cover the following guidelines on how to remove the safety components from the pre-installed track, how to install the charger into the track and how to install the lift into the track. This section will cover all variant types of the TX lift range. 4.1 Ceiling Track Access Prior to installing the Trolley into the pre-installed track, the track entrance must first be opened.
- Page 8 4.2 Installing the Charger The section below will cover the Installation of the lift chargers into their specified Tracks. The list below specifies which chargers are compatible with which track types. ➢ Standard Charging Dock (122100) is designed for the Standard Prism Track (Track Type 1). ➢...
- Page 9 4.2.2 Installing Charging Dock Type 2 (Track Type 2) Although the charger looks different to the Type 1 Charging Dock, the installation process is the same. See below for details on installing the variant along with the variant charger images. To install the TX Charger, follow the guidance below: 1.
- Page 10 4.2.3 Installing Charging Dock Type 3 (Track Type 3, 4 and 5) Although the charger looks different to the Type 1 Charging Dock, the installation process is the same. See below for details on installing the variant along with the variant charger images. To install the TX Charger, follow the guidance below: 1.
- Page 11 4.2.4 Installing Charging Dock Type 4 (Track Type 1) – QRT Lift To install the TX Charger, follow the guidance below: 1. Complete all relevant steps in 4.1 to gain access to the Ceiling Track. 2. A step ladder is recommended for easier and safer installation. 3.
- Page 12 4.2.5 Installing Charging Dock Type 5 (Track Type 3, 4 and 5) – QRT Lift To install the TX Charger, follow the guidance below: 1. Complete all relevant steps in 4.1 to gain access to the Ceiling Track. 2. A step ladder is recommended for easier and safer installation. 3.
- Page 13 4.3 Installing the Lift The section below will cover the Installation of the lifts into their specified Tracks. Refer to the Table in the introduction to determine if the lift available is compatible with the pre-installed track. Do not use a variant lift and track together as they are incompatible.
- Page 14 4.3.2 Installing TX Advanced – Constant Charge (Powered Traverse and Manual Traverse) To install the TX lift, follow the guidance below: Complete all the relevant steps in section 4.1. Complete all the relevant steps in section 4.2. A step ladder is recommended for easier and safer installation. Using both hands to support the lift, align the lift horizontally with the Ceiling Track entrance.
- Page 15 4.3.3 Installing TX Advanced – Powered Auxiliary (Powered Traverse and Manual Traverse) To install the TX lift, follow the guidance below: Complete all the relevant steps in section 4.1. Complete all the relevant steps in section 4.2. A step ladder is recommended for easier and safer installation. Using both hands to support the lift, align the lift horizontally with the Ceiling Track entrance.
- Page 16 4.3.4 Installing TX Advanced – Quick Release Track (QRT) For a TX with a QRT system, the trolley must first be installed into the track before attaching the lift to the trolley. To install the TX Trolley, follow the guidance below: Complete all the relevant steps in section 4.1.
- Page 17 The section below will cover the attachment of the Carry Bar and Handset to the lift, as well as other essential requirements to fully commission the lift for use. The below procedure is relevant for both the TX600 Advanced and TX440 Advanced.
- Page 18 5.2 Attaching the Carry Bar Follow the procedure below to attach the Carry Bar to the Quick Release Hook located at the end of the Lift Tape. Open the hooks locking mechanism by pressing the red tab downward as shown. (Figure 61 and 62) Position the carry bar horizontally as shown in figure 63 and place the attachment point into the open hook.
- Page 19 The section below will show how to start up the lift for the use of the customer as well as completing some basic functional checks to ensure the lift is in working order. The images below refer to the TX600 Advanced, but the same procedure applies to all models.
- Page 20 6.3 Traversing the Lift along the Track Always use extreme care when moving the lift along the track. Watch out for and avoid any obstructions that may cause injury to the individual in the sling, damage to the lift and/or to the obstruction. This applies to both manual and powered traversing. After use, the lift should be located at the correct end of the track system for re-charging.
- Page 21 The following section will instruct on how to correctly decommission the TX lift at the end of use. This section is relevant to both the TX600 Advanced and TX440 Advanced. The product may be contaminated and has to be disinfected before decommissioning.
- Page 22 While every effort has been made to ensure the accuracy of information contained in this installation manual, no liability can be accepted by Mackworth for any errors or omissions. Mackworth operates a policy of continuous improvement. Specifications and other data are subject to change without notice.
Need help?
Do you have a question about the TX600 Advanced and is the answer not in the manual?
Questions and answers