Related Manuals for Mackworth TX440-122515
Summary of Contents for Mackworth TX440-122515
- Page 1 TX Ceiling Track Hoist Commissioning Manual Doc No. 996553 Revision of document: A Revision Date: 08.04.2021...
-
Page 2: Table Of Contents
Contents Introduction ............................3 Safety Precautions ..........................4 Required Tools and Equipment for Hoist Commissioning and Decommissioning ......5 Hoist Unboxing ............................6 Hoist Installation ............................. 7 Ceiling Track Access ..........................7 Installing the Charger .......................... 8 4.2.1 Installing Charging Dock Type 1 (Track Type 1) ................8 4.2.2 Installing Charging Dock Type 2 (Track Type 2) ................ -
Page 3: Introduction
Type 3 Type 5 When Commissioning the Mackworth TX Hoist, one of the above track profiles should match the track the hoist is about to be installed into. To ensure the hoist available is compatable with the pre-installed track, refer to the table below. -
Page 4: Safety Precautions
The hoist is not intended to be used in environments where there are rapid changes in the environmental temperature and humidity during intended use. Any commissioning or decommissioning of the Hoist that has not been carried out by an authorised Mackworth personnel will void the product warranty. -
Page 5: Required Tools And Equipment For Hoist Commissioning And Decommissioning
Required Tools and Equipment for Hoist Commissioning and Decommissioning When carrying out work on the Ceiling Track Hoist you will require the following: Tools Required 2mm T Bar Allen wrench 2.5mm T Bar Allen wrench 3mm T Bar Allen wrench 4mm T Bar Allen wrench 5mm T Bar Allen wrench 5.5mm combination spanner... -
Page 6: Hoist Unboxing
Hoist Unboxing This section will summarize the layout of the Hoist Packaging and what is included in the Box. It is recommended a small pocketknife is used for smoother unpacking of the Hoist. The Hoist is packed into a single box (280x670x365), weighing approximately 11 kg (24 lb). -
Page 7: Hoist Installation
Hoist Installation This section will cover the following guidelines on how to remove the safety components from the pre-installed track, how to install the charger into the track and how to install the Hoist into the track. This section will cover all variant types of the TX hoist range. Ceiling Track Access Prior to installing the Trolley into the pre-installed track, the track entrance must first be opened. -
Page 8: Installing The Charger
Installing the Charger The section below will cover the Installation of the Hoist chargers into their specified Tracks. The list below specifies which chargers are compatible with which track types. ➢ Standard Charging Dock (122100) is designed for the Standard Prism Track (Track Type 1). ➢... -
Page 9: Installing Charging Dock Type 2 (Track Type 2)
4.2.2 Installing Charging Dock Type 2 (Track Type 2) Although the charger looks different to the Type 1 Charging Dock, the installation process is the same. See below for details on installing the variant along with the variant charger images. To install the TX Charger, follow the guidance below: 1. -
Page 10: Installing Charging Dock Type 3 (Track Type 3, 4 And 5)
4.2.3 Installing Charging Dock Type 3 (Track Type 3, 4 and 5) Although the charger looks different to the Type 1 Charging Dock, the installation process is the same. See below for details on installing the variant along with the variant charger images. To install the TX Charger, follow the guidance below: 1. -
Page 11: Installing The Hoist
Installing the Hoist The section below will cover the Installation of the Hoists into their specified Tracks. Refer to the Table in the introduction to determine if the Hoist available is compatible with the pre-installed track. Do not use a variant Hoist and track together as they are incompatible. -
Page 12: Component Attachment
Component Attachment The section below will cover the attachment of the Carry Bar and Handset to the Hoist, as well as other essential requirements to fully commission the Hoist for use. The below procedure is relevant for all TX Hoists. A sturdy ladder or steps may be required in order to access the underside of the Hoist to attach the handset. -
Page 13: Attaching The Carry Bar
Attaching the Carry Bar Follow the procedure below to attach the Carry Bar to the Quick Release Hook located at the end of the Lift Tape. Open the hooks locking mechanism by pressing the red tab downward as shown. (Figure 30 and 31) Position the carry bar horizontally as shown in figure 32 and place the attachment point into the open hook. -
Page 14: Hoist Start Up And Function Checks
Hoist Start Up and Function Checks The section below will show how to start up the Hoist for the use of the customer as well as completing some basic functional checks to ensure the Hoist is in working order. The images below refer to the TX600, but the same procedure applies to all models. -
Page 15: Manually Traversing The Hoist Along The Track
Manually Traversing the Hoist along the Track Always use extreme care when moving the hoist along the track. Watch out for and avoid any obstructions that may cause injury to the individual in the sling, damage to the hoist and/or to the obstruction. After use, the hoist should be located at the correct end of the track system for re-charging. -
Page 16: Decommissioning
Decommissioning The following section will instruct on how to correctly decommission the TX Hoist at the end of use. This section is relevant to all TX variants. The product may be contaminated and has to be disinfected before decommissioning. See section ‘Cleaning’ in the User Manual for details of how to do this. Hoist Removal The removal of the Hoist is essentially the Commissioning Steps in reversal. - Page 17 While every effort has been made to ensure the accuracy of information contained in this installation manual, no liability can be accepted by Mackworth for any errors or omissions. Mackworth operates a policy of continuous improvement. Specifications and other data are subject to change without notice.
Need help?
Do you have a question about the TX440-122515 and is the answer not in the manual?
Questions and answers