Related Manuals for SolaX Power X1-Micro 1300 W
Summary of Contents for SolaX Power X1-Micro 1300 W
- Page 1 X1-Micro 4 in 1 1300 W / 1500 W / 1600 W / 1800 W / 2000 W / 2200 W Installation Manual Version 4.0 www.solaxpower.com eManual in the QR code or at http://kb.solaxpower.com/...
- Page 3 Safety 1. Contents may be periodically updated or revised. SolaX reserves the right to make improvements or changes in the product(s) and the program(s) described in this manual without the prior notice. 2. The installation, maintenance and grid-related setting can only be performed by qualified personnel who: •...
- Page 4 WARNING! Risk of personnel injury or inverter damage • During operation, do not touch any parts including the enclosure lid of the inverter. • Never connect or disconnect the AC or DC connectors when the microinverter is running. • Make sure that the input DC voltage ≤ Maximum DC input voltage of the inverter. Overvoltage may cause permanent damage to the inverter, which is NOT covered by the warranty.
- Page 5 Packing List Including in the box: Microinverter Installation Map Make sure N for North Panel type: Customer information: Gateway series number: Azimuth: Tilt: Sheet_of_ COLUMN Installation map × 1 Inverter × 1 Documents Sold separately: AC trunk port disconnect 1.2m/2m/2.4m AC trunk AC trunk end cap AC trunk connector tool...
- Page 6 NOTICE! • For outdoor-installation, precautions against direct-sunlight, rain -exposure and snow-accumulation are-recommended. • Exposure to direct sunlight raises the temperature inside the device. This temperature rise poses no safety risks,but-may impact the device performance. Installation Angle Parallel to the rail Microinverter should be placed beneath the PV modules...
- Page 7 Additionally Required Materials Required Material Requirements Current: 50A for 10 AWG/40 A for 12 AWG (If there are additional safety AC circuit breaker regulations, please refer to the local safety regulations) Guide rail According to actual needs Sliding block Matching with the guide rail Screw Matching with the guide rail AC cable...
- Page 8 Maximum over X1-Micro 2000 X1-Micro 2200 current protection device 2@220V 2@220V Maximum number 2@230V 2@230V 40 A per 12AWG branch 2@240V 2@240V Note: An AC branch can connect to 1 in 1/2 in 1/4 in 1 microinverters at the same time, provided that the total current is less than the AC branch circuit capacity stipulated in local rules and regulations.
- Page 9 Item Description Antenna To receive and transmit WiFi signal. AC terminal For AC connection. A connection component for electrical devices which Earth lug need grounding (perferred grounding method). Mechanical Installation 9±0.1 N·m NOTICE! • Choose the screwdriver according to the corresponding screws of the rail. •...
- Page 10 NOTICE! • The connection between female connector and AC trunk cable is the similar to that of male connector. Connect female connector with female pin contact and install the female connector at the other side of AC trunk cable. NOTICE! •...
- Page 11 NOTICE! • In order to better fix the AC trunk cable, it is recommended to use more cable ties to band the AC trunk cable. NOTICE! • When connecting AC cables in the middle, please follow the diagram below. Female Male Female Male...
- Page 12 NOTICE! • If you need to disconnect the AC connector from the AC cable, use the AC Trunk Port Disconnect Tool (see packing list). X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X paste PE Connection...
- Page 13 Method 2: Strip the PE cable, place the PE cable on the rail and fix it with screws. 1.2 ± 0.1 N·m PV Connection NOTICE! • At least two or three trained and experienced workers are required to finish this step. WARNING! •...
- Page 14 Cover the PV pannels NOTICE! • The length of AC end cable shall depends on the actual installation scene. Ground Connect L, N and PE AC end cable-M cable to the distribution box accordingly NOTICE! • If you didn't buy AC end cable-M, please follow the procedures below to make the wire before connecting to the distribution box.
- Page 15 part I Dissemble part II part III part IV Strip Strip 7 mm Ground AC end cable-M Connect L, N and PE cable to the distribution box accordingly...
- Page 16 Power on the System Step 1: First turn on the AC breaker on the branch circuit and then the main AC breaker of the house. Step 2: Wait for about 2 minutes until the system is initiated. <2.4 m AC junction box Red-L Black-N Green/Yellow-PE...
- Page 17 Step 2: Run the App, select the language, and touch [Sign up] at the bottom of Monitoring App. Step 3: Create the account. Log in the App after registration finished. xxxxxxxxxx xxxxxxxxxx...
- Page 18 Step 4: Create a site by filling in the site information. Step 5: Click [Microinverter], scan the QR code of microinverter to bind the device. XXXXXXXXXXX NOTICE • If scanning the QR code step fails,.then try to scan the one dimensional code. Scanning one dimensional code may lead to inaccurate scan results).
- Page 19 Step 6: Enter your WiFi account and password. Then, connect the device hotspot (name: Wifi_XXXXXXXXXX), start to configure the device network. XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX NOTICE! • Before Network configuration, make sure the DC or AC side of the microinverter has been energized and the dongle moudle has been connected to "Upgrade/Dongle"...
- Page 20 XXXXXXXXXXX XXXXXXXXXXX Step 8: Click [Layout] to customize your device layout and save the settings.
- Page 21 Step 9: Click the site to view your device detail information. Technical Data • DC Input Model X1-Micro 1300 X1-Micro 1500 X1-Micro 1600 Max. recommended DC power [W] 300 to 505+ 320 to 540+ 360 to 600+ Max. PV voltage [d.c. V] MPPT voltage range [d.c.
- Page 22 Model X1-Micro 1800 X1-Micro 2000 X1-Micro 2200 Max. recommended DC power [W] 400 to 600+ 400 to 670+ 400 to 670+ Max. PV voltage [d.c. V] MPPT voltage range [d.c. V] 4 × 16 4 × 18 4 × 19.5 Max.
- Page 23 Model X1-Micro 1800 X1-Micro 2000 X1-Micro 2200 Rated output apparent power [VA] 1800 2000 2200 Maximum continuous output power 1800 2000 2200 [VA] Nominal AC voltage [a.c. V]¹ 220 or 230 or 240 / 180-264 Nominal AC frequency [Hz]¹ 50/60 8.19@220V 9.10@220V 10.00@220V...
- Page 24 Model X1-Micro 1300 X1-Micro 1500 X1-Micro 1600 Humidity [%] 0 ~ 100(condensing) Storage temperature [°C] -40 to 65 Model X1-Micro 1800 X1-Micro 2000 X1-Micro 2200 Efficiency Nominal MPPT efficiency 99.5% Maximum efficiency 96.5% Night power consumption [mW] <40 Standard Safety IEC62109 IEC 61000, EN 62920, EN 301489, EN 55011 IEC 61727, IEC 62116, EN 50549, VDE 4105, UNE217001, UNE217002, RD244/647,...
- Page 25 Contact Information AUSTRALIA UNITED KINGDOM Unit C-D Riversdale House, Riversdale 21 Nicholas Dr, Dandenong South VIC 3175 Road, Atherstone, CV9 1FA +61 1300 476 529 +44 (0) 2476 586 998 service@solaxpower.com.au service.uk@solaxpower.com TURKEY GERMANY Fevzi Çakmak mah. aslım cd. no 88 A Am Tullnaupark 8, 90402 Nürnberg, Karatay / Konya / Türkiye Germany...
- Page 26 Add: Unit C-D Riversdale House, Riversdale Road, Atherstone, CV9 1FA Tel: +44 (0) 2476 586 998 E-mail: service.uk@solaxpower.com Authorised Representative (AUS) Name: SolaX Power AUS Pty Ltd Add: 21 Nicholas Dr, Dandenong South VIC 3175 Tel: +61 1300 476 529 E-mail: service@solaxpower.com.au...
- Page 27 Warranty Registration Form For Customer (Compulsory) Name Country Phone Number Email Address State Zip Code Product Serial Number Date of Commissioning Installation Company Name Installer Name Electrician License No. For Installer Module ( If Any ) Module Brand Module Size(W) Number of String Number of Panel Per String Battery ( If Any )
- Page 29 SolaX Power Network Technology (Zhejiang) Co., Ltd. ADD.: No. 278, Shizhu Road, Chengnan Sub-district, Tonglu County, Hangzhou, Zhejiang, China E-mail: info@solaxpower.com 320102118604 Copyright © SolaX Power Network Technology (Zhejiang) Co., Ltd. All rights reserved.
Need help?
Do you have a question about the X1-Micro 1300 W and is the answer not in the manual?
Questions and answers