Page 3
overview IMPORTANT SAFETY INSTRUCTIONS 22. Screen distortion could occur outside of the subject distance. 23. While encoding, a real time fps fluctuation of ±1fps could occur. 1. Read these instructions. 24. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the video.
Page 4
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a ~ Do not place this apparatus on an uneven surface. protective earthing connection. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
Page 5
CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included Network I/O box - separately sold product Optional Accessories for Installation At a Glance APPENDIX Troubleshooting...
Page 6
overview RECOMMENDED PC SPECIFICATIONS RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ RAM : 8G or higher ~ Recommended capacity : 16 GB ~ 512 GB(MLC type recommended) ~ Recommended browser: Chrome ~ Recommended Manufacturers / Product Type : ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) - SanDisk / High Endurance, MAX ENDURANCE...
Page 7
WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Option (not included) Appearance Item Name Quantity Description Camera SPO-6011 Use installation screws of at least M4, L30 for the installation of this product. Quick Guide Alarm cable Used when connecting to an alarm...
Page 8
overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available. Wall Mount and Pole Mount Mounting Hole Cover Hanging Mount Wall Mount Base Corner Mount Installation Box SBP-300PMW2 SBP-300WMW (Pole Mount) (Wall Mount) * SBP-300PMW2 required for pole installation SBP-315HMW SBP-156KMW SBP-315C...
Page 9
Ceiling Mount Parapet Mount Assembly Individual Parts SBP-180CMB SBP-300LMW SBP-C15P SBP-140CMB SBP-150CMI SBP-300CMTS SBP-300CMI SBP-300CMTW SBP-180CMS SBP-150CMP SBP-C15H (Ball Head) SBP-300CMW1 (Ball Head) SBP-300CMP SBP-900CMW SBP-900CMP SBP-156LMW1 English _9...
Page 10
overview AT A GLANCE Appearance Components (Front Side) Item Description Lens 4 camera lenses show different directions. Illumination Sensor Detects incoming light to control the IR LED. Item Description IR LED These infrared LED’s are controlled by the illumination sensor. Dome cover Case cover used to protect the lens and the main unit.
Page 11
Components (Rear Side) Item Description PoE+/PoE++ Connection port This port connects power and network via PoE+/PoE++ injector. Alarm cable port This port is where you connect the alarm cable to connect to an external alarm device. English _11...
Page 12
installation & connection INSTALLATION Disassembling 1. Remove the dome cover by turning the dome cover’s fastening screws counterclockwise. Note that it is not necessary to loosen the screws completely. The camera jack connected to the external cable is not waterproof. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 13
3. Remove the camera body and mounting plate by pulling the mounting clip, as shown in the figure. Inserting a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure. Before installing the camera, the Micro SD card should be inserted while the power source and the body are separated. Do not forcefully insert it in the reverse direction.
Page 14
installation & connection Removing a Micro SD card Installation (mount plate) Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD [Directly installing on ceiling] card from the slot. 1-1.
Page 15
1-3. Take out the necessary cables from among the network and alarm cables through the hole of the mount 2-3. Place the pipe on the mount plate. plate. 2-4. Fix the mount plate using appropriate screws. [Installing using pipe] 2-1. Place the mount plate on the desired location considering the direction to be monitored, mark the locations for the screw holes, and then drill the holes.
Page 16
installation & connection [Attaching to the unbundled adapter] Installation (camera body and dome cover) Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation 1. Connect the safety wire to the mount plate. site or for your convenience.
Page 17
2. Mount the camera body to the mount plate. [Installing the network cable] (IP66) Mount it to fit the hinges as shown in the image. Use a cable bushing compliant with the network cable to be connected. Camera main: use a cable with the diameter of Ø5 to 6.5 You can only use a network cable with a diameter of Ø6.5 or less.
Page 18
installation & connection 7. Insert the cable bushing of the network cable into the camera body. 9. Connect the connector of the network cable to the camera's PoE+/PoE++ port. [Installing alarm cables] 10. Pull out the cable bushing from the camera body, as shown in the figure. 8.
Page 19
11. Insert the provided bushing of the alarm cable into the camera body. 13. Connect the cables to the ports inside the camera, and then close the cable cover until a click sound is heard. 14. Lift up the camera body and push the mounting clips until they click into place. 12.
Page 20
installation & connection 15. Fix the camera body by tightening the fastening screws on the camera body. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
Page 21
Adjusting the monitoring direction for the camera Installation precautions when using the IR mode ~ <Auto1>: Optimized for IR light to radiate evenly when the center of the object is saturated. ~ <Auto2>: Optimized for IR light to evenly radiate at the overall IR brightness. ~ <Manual>: You can manually adjust each zone to better capture the environment where the camera is installed.
Page 22
installation & connection CONNECTING WITH OTHER DEVICE Network Cable Specification Item Contents Remark Powering and networking Connector RJ45 (10/100/1000BASE-T) Connect the PoE+/PoE++ device with the PoE+/PoE++ terminal of the camera. To operate with 1000BASE-T, a cable of Ethernet 10/100/1000BASE-T Category 6 or higher should be used for the Giga hub.
Page 23
CONNECTING AUDIO AND ALARM I/O Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. You can connect audio and alarm using a network I/O box separately sold. Microphone Speaker Network ORANGE: ALARM I/O 1 ORANGE: ALARM #1 BROWN: ALARM I/O 2...
Page 24
installation & connection To connect to an external sensor To use as an Alarm IN: Connect one of the [ALARM I/O] port and the other terminal to the [GND] port. Alarm In Wiring Diagram(example) Alarm cable External connection Sensor ALARM I/O 1 ALARM I/O 2 <If ALARM I/O 1 is set as an input terminal>...
Page 25
network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET DSL/Cable Modem 1.
Page 26
If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com).
Page 27
AUTOMATICALLY CONFIGURING IP Configuring Dynamic IP Receive IP address from DHCP 1. Click the camera from the list that you want to automatically ~ Example of the Dynamic IP environment configure the IP. PNM-C32083RQZ - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2.
Page 28
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
Page 29
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
Page 30
web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
Page 31
PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 characters, you must use at least 3 system over the network.
Page 32
appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION ~ On the authentication popup window prompted when initially accessing https, click "View ~ Check if the Micro SD card is defective. Authentication Certificate" and select the "Always trust when connecting to the designated Cannot record into the Micro SD card.
Page 33
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
Need help?
Do you have a question about the PNM-C16083RQZ and is the answer not in the manual?
Questions and answers