Hanwha Vision PNM-C32084RQZ User Manual
Hide thumbs Also See for PNM-C32084RQZ:

Advertisement

Quick Links

NETWORK CAMERA
User Manual
PNM-C32084RQZ

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PNM-C32084RQZ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hanwha Vision PNM-C32084RQZ

  • Page 1 NETWORK CAMERA User Manual PNM-C32084RQZ...
  • Page 2 Network Camera User Manual Copyright ©2024 Co., Ltd. All rights reserved. Hanwha Vision Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved.
  • Page 3 overview IMPORTANT SAFETY INSTRUCTIONS 22. Screen distortion could occur outside of the subject distance. 23. While encoding, a real time fps fluctuation of ±1fps could occur. 1. Read these instructions. 24. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the video.
  • Page 4 overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a ~ Do not place this apparatus on an uneven surface. protective earthing connection. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
  • Page 5: Table Of Contents

    CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included Network I/O box - separately sold product Optional Accessories for Installation At a Glance APPENDIX Troubleshooting...
  • Page 6: Recommended Pc Specifications

    overview RECOMMENDED PC SPECIFICATIONS RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ RAM : 8G or higher ~ Recommended capacity : 16 GB ~ 512 GB(MLC type recommended) ~ Recommended browser: Chrome ~ Recommended Manufacturers / Product Type : ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) - SanDisk / High Endurance, MAX ENDURANCE...
  • Page 7: What's Included

    WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Appearance Item Name Quantity Description Appearance Item Name Quantity Description Alarm cable Used when connecting to an alarm Camera Cable bushing Extra cable bushing for network cable installation.
  • Page 8: Optional Accessories For Installation

    overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available. Wall Mount and Pole Mount Mounting Hole Cover Hanging Mount Wall Mount Base Corner Mount Installation Box SBP-300PMW2 (Pole Mount) SBP-300WMW (Wall Mount) * SBP-300PMW2 required for pole installation SBP-315HMW SBP-156KMW SBP-315C...
  • Page 9 Ceiling Mount Parapet Mount Assembly Individual Parts SBP-180CMB SBP-300LMW SBP-C15P SBP-140CMB SBP-150CMI SBP-180CMS SBP-300CMTS SBP-300CMI SBP-C15H SBP-300CMTW SBP-150CMP (Ball Head) (Ball Head) SBP-300CMW1 SBP-300CMP SBP-900CMW SBP-900CMP SBP-156LMW1 English _9...
  • Page 10: At A Glance

    overview AT A GLANCE Appearance Components (Front Side) Item Description Lens 4 camera lenses show different directions. Item Description Illumination Sensor Detects incoming light to control the IR LED. Dome cover Case cover used to protect the lens and the main unit. IR LED These infrared LED’s are controlled by the illumination sensor.
  • Page 11 Components (Rear Side) Item Description HPoE Connection port This port connects power and network via HPoE injector. Alarm cable port This port is where you connect the alarm cable to connect to an external alarm device. English _11...
  • Page 12: Installation & Connection

    installation & connection INSTALLATION Disassembling 1. Remove the dome cover by turning the dome cover’s fastening screws counterclockwise. Note that it is not necessary to loosen the screws completely. The camera jack connected to the external cable is not waterproof. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
  • Page 13 Inserting a Micro SD card Removing a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
  • Page 14 installation & connection Installing a graphics card or SSD (separately sold) 2. Insert the SSD into the SSD slot on the PCB module as shown in the figure, and then fix it with the provided screws. You can install a separately sold graphics card or SSD. The SSD has two slots.
  • Page 15 4. Once the graphics card or SSD has been installed, attach the provided thermal pad inside the PCB 6. Fix the cooling fan’s power cable so that it is not damaged or caught, and then assemble the PCB module. module cover. Check the number of the installed SSD and then attach the thermal pad.
  • Page 16 installation & connection 8. Connect the connector of the cooling fan’s power cable to the PCB module’s port. 10. Tighten the fastening screws to assemble the PCB module cover on the camera body. Assemble the camera body and PCB module cover by aligning the direction guide on them. TR20 9.
  • Page 17 Installation (mount plate) 1-3. Take out the necessary cables from among the network and alarm cables through the hole of the mount plate. [Directly installing on ceiling] 1-1. Place the mount plate on the desired location considering the direction to be monitored, mark the locations for the screw holes and cable holes, and then drill the holes.
  • Page 18 installation & connection 2-3. Place the pipe on the mount plate. [Attaching to the unbundled adapter] 2-4. Fix the mount plate using appropriate screws. Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.
  • Page 19 Installation (camera body and dome cover) 2. Pull out the cable bushing from the camera body, as shown in the figure. 1. Connect the safety wire to the mount plate. [Installing the network cable] (IP66) Use a cable bushing compliant with the network cable to be connected. Camera main: use a cable with the diameter of Ø5 to 6.5 You can only use a network cable with a diameter of Ø6.5 or less.
  • Page 20 installation & connection 5. For waterproof protection, pull down the cable below the cable bushing as shown in the figure below. 7. Open the cable cover on the camera body. If the camera's IR LED hides the cable cover, access the web viewer and then move the lens so that the cable cover is not 6.
  • Page 21 [Installing alarm cables] 10. Insert the provided bushing of the alarm cable into the camera body. 9. Pull out the cable bushing from the camera body, as shown in the figure. 11. Connect the connector of the alarm cable to its connection port. English _21...
  • Page 22 installation & connection 12. Connect the cables to the ports inside the camera, and then close the cable cover until a click sound is 14. Fix the camera body by tightening the fastening screws on the camera body. heard. TR20 13.
  • Page 23 Outdoor installation Adjusting the monitoring direction for the camera When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
  • Page 24: Connecting With Other Device

    installation & connection Installation precautions when using the IR mode CONNECTING WITH OTHER DEVICE ~ <Auto1>: Optimized for IR light to radiate evenly when the center of the object is saturated. ~ <Auto2>: Optimized for IR light to evenly radiate at the overall IR brightness. Powering and networking ~ <Manual>: You can manually adjust each zone to better capture the environment where the camera is Connect the HPoE device with the HPoE terminal of the camera.
  • Page 25: Connecting Audio And Alarm I/O

    CONNECTING AUDIO AND ALARM I/O Network Cable Specification Item Contents Remark You can connect audio and alarm using a network I/O box separately sold. Connector RJ45 (10/100/1000BASE-T) To operate with 1000BASE-T, a cable of Ethernet 10/100/1000BASE-T Category 6 or higher should be used for the Giga hub.
  • Page 26 installation & connection Connecting to the I/O port box To connect to an external sensor Connect the Alarm I/O cable to the corresponding port of the port box. To use as an Alarm IN: Connect one of the [ALARM I/O] port and the other terminal to the [GND] port. Alarm In Wiring Diagram(example) Alarm cable External connection...
  • Page 27: Network Connection And Setup

    network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE You can set up the network settings according to your network configurations. MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET DSL/Cable Modem 1.
  • Page 28: Using Device Manager

    If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com).
  • Page 29: Manually Registering Camera

    ~ Example of the Dynamic IP environment configure the IP. PNM-C32084RQZ - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
  • Page 30: Port Range Forward (Port Mapping) Setup

    network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen.
  • Page 31: Connecting To The Camera From A Shared Local Pc

    CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
  • Page 32: Connecting To The Camera

    web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1.
  • Page 33: Password Setting

    PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 characters, you must use at least 3 system over the network.
  • Page 34: Troubleshooting

    appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION ~ On the authentication popup window prompted when initially accessing https, click "View No signal is found at the Alarm Output Authentication Certificate" and select the "Always trust when connecting to the designated port even when an intelligent video ~ Check alarm output port settings.
  • Page 35 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.

Table of Contents