Related Manuals for Hanwha Vision PNM-C20000QB
Summary of Contents for Hanwha Vision PNM-C20000QB
- Page 1 NETWORK CAMERA User Manual PNM-C20000QB/ SLA-T1080FA/SLA-T2480A/SLA-T2480VA/SLA-T2880BA/ SLA-T4680A/SLA-T4680VA/SLA-T4680DA/SLA-T4680DSA/ SLA-T2480WA/SLA-T2480WDA SCL-150...
-
Page 2: Network Camera
Network Camera User Manual Copyright ©2025 Co., Ltd. All rights reserved. Hanwha Vision Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. -
Page 3: Important Safety Instructions
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. from 12 Vdc, 1.93 A / PoE (53Vdc), 0.48 A. (PNM-C20000QB) 16. This Lens module has to be connected with equipment, which supplied by a power supply unit marked “Class 2”... - Page 4 overview Class construction The ITE is to be connected only to PoE networks without routing to the outside plant. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3at shall be a UL Listed device with the output evaluated as a Limited Power Source protective earthing connection.
-
Page 5: Table Of Contents
Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup NAS recommended specs What’s Included (PNM-C20000QB) What’s Included (Lens module/Extension cable - Optional) At a Glance APPENDIX Troubleshooting INSTALLATION & CONNECTION Installation... -
Page 6: Recommended Pc Specifications
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher ~ Recommended capacity : 200GB or higher is recommended. ~ RAM : 8G or higher ~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. ~ Recommended browser: Chrome Recommended products : QNAP NAS, Synology NAS ~ Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) -
Page 7: What's Included (Pnm-C20000Qb)
WHAT’S INCLUDED (LENS MODULE/EXTENSION CABLE - OPTIONAL) Please check if your camera and accessories are all included in the product package. This is a lens module separately sold that is mounted to PNM-C20000QB. (As for each sales country, accessories are not the same.) Please check if your camera and accessories are all included in the product package. - Page 8 overview Model Name Appearance Item Name Quantity Description Model Name Appearance Item Name Quantity Description Lens Module Lens Module Quick Guide Quick Guide (Optional) (Optional) Tapping Screw Used for installation on the wall or ceiling Lens module bracket Use this for lens module installation SLA-T2480VA Cable tie Use this for organizing the cable...
- Page 9 Model Name Appearance Item Name Quantity Description Model Name Appearance Item Name Quantity Description Double-sided tape Used to fix brackets on glass Lens Module Used to remove pollutants on surfaces Quick Guide Surface cleaner where brackets are attached (Optional) SLA-T2880BA Used as tapping screw covers for floor Screw cover installation...
- Page 10 overview Model Name Appearance Item Name Quantity Description Model Name Appearance Item Name Quantity Description Lens Module Lens Module Quick Guide Quick Guide (Optional) (Optional) Tapping Screw Used for installation on the wall or ceiling SLA-T4680VA Lens module bracket Use this for lens module installation Cable tie Use this for organizing the cable SLA-T4680A...
- Page 11 Model Name Appearance Item Name Quantity Description Model Name Appearance Item Name Quantity Description Lens Module Lens Module Quick Guide Quick Guide (Optional) (Optional) SLA-T2480WA Use this when fixing the lens module Lens module bracket Use this for lens module installation Cable to connect lens Use this when connecting the main unit SLA-T4680DA/...
- Page 12 overview Model Name Appearance Item Name Quantity Description Model Name Appearance Item Name Quantity Description Cable to connect lens module Use this when connecting the main unit SCL-150 Lens Module (15 m) and lens module Quick Guide (Optional) SLA-T2480WDA Cable to connect lens Use this when connecting the main unit module and lens module...
-
Page 13: At A Glance
AT A GLANCE Item Description ON : While the power is on Power indicators POWER OFF : If the power is off Status Indicators for Lens The LED turns on when each channel video is successfully displayed. Module Connection terminal of lens This terminal is connected to the lens module through the cable to connect the lens module module. - Page 14 overview Appearance of lens module <SLA-T2480VA> <SLA-T4680VA> <SLA-T1080FA> <SLA-T2480A> <SLA-T2480WA> <SLA-T2480WDA> <SLA-T4680A> Item Description Lens Module This lens module is used to shoot video. Main unit connection This terminal is connected to the main unit through the cable to connect the lens module. terminal 14_ overview...
-
Page 15: Installation And Connection
installation & connection INSTALLATION Removing a Micro SD card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Precautions before installation Ensure you read out the following instructions before installing the camera: ~ Organize the cable separately in order to prevent excessive burden on the lens module while the camera is installed (within 1m from the lens module ). - Page 16 installation & connection 2. Install the main unit with the installation bracket on the wall using appropriate screws. 4. Connect the network cable to the main unit’s PoE+ port. 3. Connect the alarm terminal block to the main unit’s ALARM port. 16_ installation &...
-
Page 17: Install Lens Module
INSTALL LENS MODULE Installing(Lens module - Optional) 1. Connect the lens module cable to the main unit’s lens module connection port. This is how to install the lens module purchased separately. Connect the lens module and turn it on. SLA-T1080FA Turn off the main unit power when connect or remove lens module 1. - Page 18 installation & connection SLA-T2480A/SLA-T4680A SLA-T2480VA/SLA-T4680VA 1. Use two screws provided or remove protective film to use the double- 1. Make a hole for the lens module at the spot where you want to install it. sided tape on the bottom side of the lens module bracket to install the lens module bracket.
- Page 19 Connect lens module cable to lens module Adjust the length of the cable for connecting the lens module The length of the cable for connecting the main unit and lens module can be adjusted. Please follow the 1. Unscrew the back cover by turning it counterclockwise. steps in the correct order to adjust the length of the cable for connection: Be sure to remove the back cover first and assemble/disassemble the RJ45 1.
-
Page 20: Connecting With Other Device
installation & connection CONNECTING WITH OTHER DEVICE Powering and networking Connect the PoE+ device with the PoE+ port of the Main Unit. WiFi dongle PoE+ Router internet HDMI Supported Monitor Connect and use a PoE+ -enabled router. Use a PoE+ device that complies with the IEEE 802.3at standard. PoE+ or DC 12V power connection If you connect using an PoE+ -enabled router, you don’t need a separate power supply cable to power it on. - Page 21 Power Supply Connecting WiFi Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the Camera Setup camera. 1. Connect the OTG gender (Type-C) and WiFi dongle to the USB Type-C terminal. If the power sources for PoE+ and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE+ Smartphone Setup and DC 12V.
- Page 22 installation & connection Connecting to Audio Input/Output Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. Microphone Speaker Function Description These 4 ports are configurable from the web viewer, as they can be used as Alarm in or Alarm ALARM I/O 1~ ALARM I/O 4 ※...
- Page 23 To connect to an alarm output If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause damage. (DC 12 V/50 mA MAX) Refer to the alarm out connection diagram below case. Alarm Out Wiring Diagram(example) Alarm cable External connection...
-
Page 24: Network Connection And Setup
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1. -
Page 25: Using Device Manager
If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Support>-<Online Tool> menu at Hanwha Vision website ex) 192.168.1.2~254, 192.168.0.2~254, (https://www.HanwhaVision.com). -
Page 26: Configuring Dynamic Ip
~ Example of the Dynamic IP environment configure the IP. PNM-C20000QB - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager. -
Page 27: Port Range Forward (Port Mapping) Setup
PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the ~ A user can change each port using the camera setting screen. -
Page 28: Connecting To The Camera From A Shared Local Pc
network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser. -
Page 29: Web Viewer
web viewer CONNECTING TO THE CAMERA Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. Normally, you would 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. 1. -
Page 30: Password Setting
web viewer PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the login password. 1. Click the [Setup ( )] icon. 2. The Settings window appears. For a new password with 8 to 9 characters, you must use at least 3 3. -
Page 31: Troubleshooting
appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM SOLUTION ~ Verify the settings in the following sequence: When an Windows 10 user accesses <Motion detection> of <Analytics> is ~ This is what happens when microphone driver has been set to Realtek driver. the web viewer through Chrome set to <Enable>, but no notification A. - Page 32 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.
Need help?
Do you have a question about the PNM-C20000QB and is the answer not in the manual?
Questions and answers