Advertisement
Quick Links
Advertisement
Related Manuals for laguna X|Flux: 10HP
Summary of Contents for laguna X|Flux: 10HP
- Page 1 10 HP Cyclone Owner’s Manual 10HP EXPLOSION-SUPPRESSION SYSTEM...
- Page 2 Below is a QR code which will direct you to the manual reference page, where the latest version of the 10 HP DUST COLLECTOR manual is located on the Laguna Tools website. The online manual may have updates and information added after the printed copy was released. Scan the code with your smartphone or copy the URL link to be directed to the latest manual page to reference your specific machine and model.
- Page 3 Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
- Page 4 4. Do not use this machine for other than its intended use. If used for other purposes, LAGUNA TOOLS INC., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
- Page 5 • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.
- Page 6 Give your work undivided attention. Looking around, carrying on a conversation and “horseplay” are careless acts that can result in serious injury. Maintain a balanced stance at all times so that you do not fall or lean against the dust collector. Do not overreach or use excessive force to perform any machine operation.
- Page 7 KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use this unit in damp or wet locations or expose it to rain. Keep the work area well-lighted.
- Page 8 Do not operate the dust collector in rainy or wet locations— exposure to water may create a shock hazard or decrease the life of the machine.
- Page 9 Make sure to regularly clean the surrounding area where the machine is operated—excessive dust buildup on overhead lights, heaters, electrical panels, or other heat sources will increase the risk of fire.
- Page 10 POWER CONNECTIONS/ELECTRICAL DIAGRAM DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS. 10HP Dust Collector Manual...
- Page 11 In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire can result in a risk of electric shock.
- Page 12 220 VOLT Three-Phase Operation The motor supplied with your machine is a 220 volt motor. It is shipped ready-to-run for 220 volt, 3 Ph operation. FUNCTION High frequency remote control switch Canister Filter detection Octagon drum detection On board circuit breaker ON/OFF Switch Handheld remote controller ON button...
- Page 13 (272 x 126 x 205 cm) Machine weight 1653.5 lbs. (750 kgs) Shipping weight 1829.8 lbs. (830 kgs) Filter Media filtering area: 24.3m2 (261.6 ft2) Cartridge Filter 1 Micron Ø20.08” x 35.43” (Ø51 x 90cm) x 3 pcs. 10HP Dust Collector Manual...
- Page 14 G. Handheld remote controller O. Operating and Parts Manual H. Vacuum suction plate (3) P. Intake 12” Report any missing or damaged parts to your dealer or distributor. Prior to tool assembly and use, read this manual thoroughly to familiarize yourself with proper assembly, maintenance, and safety procedures.
- Page 15 GENERAL TOOL ASSEMBLY This step requires two adults. This 10HP Explosion Suppression Vacuum Dust Collector is heavy, be careful when lifting and handling it! Failure to comply may cause serious injury and/or damage to the machine and/or property! Tools Required 10mm wrench / 12mm wrench / 14mm wrench Phillips screwdriver 4mm hex wrench / 5mm hex wrench...
- Page 16 Step Two: Secure the four wheels to the upright support panels using (16) 3/8”x1” hex bolts and (16) 3/8”x23x2 flat washers. Step Three. Secure the upright support to the right side of the machine when facing the control panel. Use (13) 3/8”x1” hex bolts and (13) 3/8”x23x2 flat washers.
- Page 17 Step Three. Secure the upright support to the left side of the machine when facing the control panel. Use (13) 3/8”x1” hex bolts and (13) 3/8”x23x2 flat washers. Step Four: Secure the latch base plate to the front side of the drum lid using (2) 3/16”*3/8”...
- Page 18 Step Five: Secure the casters to the drum base panel using (8) 3/8”x23x2 flat washers and (4) 3/8” nuts. Step Six: Assemble the front and back panel to the drum base using (10) 5/16”x5/8” Philips hd bolts, (20) 5/16”x18x2 flat washers and (10) 5/16” nuts.
- Page 19 Step Seven: Assemble the side panels to the drum using (6) 5/16”x5/8” Philips hd bolts, (12) 5/16x18x2 flat washers and (6) 5/16” nuts to secure the base. And then use (16) 5/16”x5/8” Philips hd bolts, (16) 5/16”x18x2 flat washers and (16) 5/16”...
- Page 20 Step Nine: Assemble the latch to the drum using (4) 3/16”x3/8” round head thread bolts. Step Ten: Attach the 2-1/2”x2M flex hose to the drum and drum lid. Do the same for the other two drums. 10HP Dust Collector Manual...
- Page 21 Step Eleven: Place the vacuum suction ring inside before inserting the plastic bag in the Octagon drum. Vacuum suction ring Step Twelve: Once completing the assembly, apply silicone to the inside of the drum including the base to seal and prevent air leakage. Silicone 10HP Dust Collector Manual...
- Page 22 Step Thirteen: Attach the 12” intake to the left side of the machine as shown below using (10) 5/16”x3/4” hex bolts and (10) 5/16”x18x2 flat washers. Step Fourteen: All the assembly steps have been completed. 10HP Dust Collector Manual...
- Page 23 CLEANING THE FILTER To ensure proper operation of this Dust Cyclone, the canister filter must have adequate air flow. This means the filter must be regularly maintained by carefully blowing the filter clean using compressed air and an air gun to release built-up particulates trapped between the filter pleats.
- Page 24 Loosen the bolt and remove from the rotation shaft as shown below. Set the shaft aside for later use. Keep the bolt for use when reassembling the rotation shaft. 3. Remove the adjustable clamp from the canister filter located at the bottom to remove the canister filter from the housing.
- Page 25 4. With the canister filter removed use a compressed air gun to thoroughly clean between the pleats, both inside and outside. RE-ASSEMBLING THE CANISTER FILTER AFTER CLEANING 1. With the aid of another person, carefully re-insert the canister filter repeating steps above in reverse. EMPTYING OR REPLACING THE FILTER BAG Periodically check the filter bag, if it is more than one third full, it is recommended that you empty it.
- Page 26 2. Roll it away from the machine, inspect and empty as needed. ROUTINE INSPECTION It is a good idea to routinely inspect any quality woodworking tool to keep it in optimum condition. This includes inspecting all hardware for tightness, ensuring the filter is clean, and cleaning debris and grime from any surfaces and moving parts.
- Page 27 TROUBLESHOOTING GUIDE Symptom Possible Cause Possible Solution Machine Power supply switched Confirm power supply is ON and does not OFF or is faulty. has the correct voltage. start or a breaker Wall fuse/circuit breaker is Ensure adequate circuit size; trips. blown/tripped.
- Page 28 Loud, Machine is on uneven Stabilize on a flat surface. repetitive surface. noise, or excessive Damaged/Unbalanced Inspect impeller for dents, vibration impeller. bends, loose fins. Replace it coming from if needed. cyclone Loose connections. Check and re-tighten all fasteners. Replace the motor and Impeller loose.
- Page 29 Parts Breakdown 山富機械公司 2016.05.19 出圖章 10HP Dust Collector Manual...
- Page 30 Part List Ref No Part Name Description UPRIGHT SUPPORT STAND 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER MACHINE CASTER 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER UPPER BODY LOWER BODY 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER PROXIMITY SENSOR RUBBER SEAL HANDLE 5/16”*3/4”...
- Page 31 Ref No Part Name Description 1/4” HEX LOCK NUT WINDOW RIVET MACHINE BODY – SIDE PANEL 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER 3/8” HEX LOCK NUT MACHINE BODY – MIDDLE PANEL 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER MIDDLE CONNECTOR PANEL 3/8”*...
- Page 32 RIGHT SUPPORT BASE 18-2 LEFT SUPPORT BASE 5/16”*3/4” THREAD BOLT 19-1 RIGHT DOOR 19-2 LEFT DOOR DOOR HANDLE HINGE BASE – LOWER HINGE BASE – TOP 5/16”*3/4” THREAD BOLT HANDLE LATCH 1/4”*5/8” PHILIP HD BOLT HINGE 5/16”*3/4” HEX BOLT 5/16”*OD18*2t FLAT WASHER Ø500...
- Page 33 Ref No Part Name Description 3/8”*OD23*2t FLAT WASHER 3/8” HEX LOCK NUT 3/8”*1” RING SILENCER 5/16”*3/4” HEX BOLT 5/16”*OD18*2t FLAT WASHER DUST CHUTE 3/8”*1” HEX BOLT 3/8”*OD23*2t FLAT WASHER CONTROL SUPPORT PLATE 1/4” HEX NUT CONTROL BOX DOOR HANDLE 1”...
- Page 34 1/2”*OD34*2.5t FLAT WASHER 1/2” HEX NUT 1/2” LOCK WASHER 15.5” IMPELLER IMPELLER BOLT M10*25 3/8”*3Tø45 IMPELLER SPECIAL WASHER INTAKE – SQUARE TO ROUND 12” 5/16”*3/4” HEX BOLT 5/16”*OD18*2t FLAT WASHER DRUM LID 1/4”*5/8” HEX BOLT 1/4”*OD18*2t FLAT WASHER 1/4” LOCK NUT OCTAGON DRUM BASE PANEL 1/4”*5/8”...
- Page 35 Ref No Part Name Description OCTAGON DRUM BACK PANEL DRUM VACUUM TUBE 1/4”*5/8” PHILIP HD BOLT 1/4”*OD18*2t FLAT WASHER HOSE CONNECTOR HOSE CLAMP 2-1/2” GRAY FLEX HOSE 2-1/2”*2M OCTAGON DRUM SIDE PANEL 1/4”*5/8” HEX BOLT 1/4”*OD18*2t FLAT WASHER 1/4” LOCK NUT...
- Page 37 Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.
Need help?
Do you have a question about the X|Flux: 10HP and is the answer not in the manual?
Questions and answers