Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for laguna iFlux 10 Elite
Summary of Contents for laguna iFlux 10 Elite
- Page 1 FILTER 10HPBAG DUST COLLECTOR...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions Safety Guidelines - Definitions General Safety Rules Additional Safety For Dust Collectors Power Connections Motor Specifications Grounding Instructions Key Features and Components Functional Description Product Specifications Assembly General Tool Assembly Maintenance Procedures Cleaning the Filter Routine Inspection Trouble Shooting Parts breakdown and parts list... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage. Woodworking can be dangerous if safe and proper operating procedures are not followed. - Page 4 4. Do not use this machine for other than its intended use. If used for other purposes, LAGUNA TOOLS INC., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
- Page 5 8. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead based paint. • Crystalline silica from bricks, cement and other masonry products.
-
Page 6: Safety Guidelines - Definitions
18.Keep the floor around the machine clean and free of scrap material, oil and grease. 19.Keep visitors a safe distance from the work area. Keep children away. 20.Make your workshop child proof with padlocks, master switches or by removing starter keys. 21.Give your work undivided attention. -
Page 7: General Safety Rules
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. -
Page 8: Additional Safety For Dust Collectors
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. ADDITIONAL SAFETY FOR DUST COLLECTORS Intended use. This dust collector is only intended for collecting wood dust and chips from woodworking machines. Do not use this dust collector to collect metal, dirt, pebbles, drywall, asbestos, lead paint, silica, liquids, aerosols, or any flammable, combustible, or hazardous materials. - Page 9 cause serious personal injury or damage to the machine. Always keep small animals and children away from open dust collection inlets. Avoiding sparks. Do not allow steel or rocks to strike the impeller—this may produce sparks. Sparks can smolder in wood dust for a long time before a fire is detected. If you accidentally cut Into wood containing tramp metal (nails, staples, spikes, etc.), immediately turn off the dust collector, disconnect it from power, and wait for the...
-
Page 10: Power Connections
POWER CONNECTIONS Electric drawing: 10HP Bag Filter Dust Collector Manual... -
Page 11: Motor Specifications
MOTOR SPECIFICATIONS Your machine is wired for 220V, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position. GROUNDING INSTRUCTIONS THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. 1. - Page 12 IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE. 220V Three-Phase Operation The motor supplied with your machine is a 220 volt motor. It is shipped ready-to-run for 220 volt operation.
- Page 13 4. Move the R1 wire on the transformer from the 220V terminal to the 440V terminal. Remove the T1 wire from the 0 terminal to the top O terminal. (See figure below) 5. Open the motor junction box, rewire the motor terminals for 440V power.
- Page 14 CONTROL PANEL DESCRIPTION METER ON/OFF SWITCH REBOOT SWITCH 10HP Bag Filter Dust Collector Manual...
-
Page 15: Product Specifications
PRODUCT SPECIFICATIONS Motor Specs: 10 HP Electrical Specs: 220V/440V / 60Hz / 3PH / 1720 RPM Running AMP 28A at 220V; 14A at 440V Air Volume: 5500CFM (cubic feet per minute) Max. static pressure 6.5 Inches of water Fan size 22”... -
Page 16: General Tool Assembly
GENERAL TOOL ASSEMBLY Tools Required Open end wrench 12 (not supplied) Open end wrench 14 (not supplied) Open end wrench 17 (not supplied) SEVERE LACERATION HAZARD. TURN THE UNIT “OFF”, DISCONNECT THE UNIT from the power source and wait 2- 1/2 minutes to allow time for internal rotating components to stop before installing or removing accessories, before adjusting or changing set-ups, clearing clogs or when making repairs. - Page 17 Fig.5 Fig.6 2. TOP FILTER BAG SUPPORT RODS With the help of three other people; you need to lift the upper frame and insert the top filter bag support rods (Fig. 4). After inserting it into the upper frame, make sure to use the hex bolts 5/16”...
- Page 18 5. ASSEMBLE MOTOR HOUSING TO FILTER BAG HOUSING Use a crane to lift the motor housing up to about 5 feet high. Be careful that the motor housing does not swing around and cause injury. Use a fork lift and place a wooden pallet on the forks that will be used to lift the filter bag housing.
- Page 19 7. ASSEMBLE CONTROL PANEL Take control panel and assemble to the motor housing using hex bolts 3/8”, flat washers 3/8” and lock nut 3/8”. (Fig.15) There are three points on the top Fig.15 of the control panel to secure with the hex bolts. And two Fig.16 points on the leg stand to secure with the hex bolts.
- Page 20 9. ASSEMBLE EZ LIFT Fig.20 HANDLE First remove the three hex bolts 3/8”, flat washers 3/8” and lock 3/8” from underneath the lower filter housing. Set aside for use Fig.19 when you assemble the ez lift handle. The inner row of bolts will need to bolt on with one hand/arm reaching in from inside the filter housing.
-
Page 21: Routine Inspection
HOOK UP THE CLOTH Fig.24 Fig.25 CONNECTION Attach the black cloth connection to the rim under the filter housing. Use the band clamp to secure in place. Do the same for the other drum. (Fig.24 and Fig. 25) PLASTIC BAG INTO DRUMS Put the plastic bags into the drums before closing the drums in place. -
Page 22: Trouble Shooting
TROUBLESHOOTING GUIDE Symptom Possible Cause Possible Solution Machine Power supply switched Ensure power supply is ON and does not OFF or is faulty. has the correct voltage. start or a breaker Wall fuse/circuit breaker is Ensure adequate circuit size; trips. blown/tripped. - Page 23 Dust Canister end bag is full. Empty canister end bag. collector does not Filter is dirty. Clean filter. adequately collect dust Restricted duct line. Clean inlet adapter. or chips; poor Suction route is too long Move machine closer to the point performance.
- Page 24 Parts Breakdown 10HP Bag Filter Dust Collector Manual...
- Page 25 Part List Ref No Part Name Description Q’TY MOTOR 10HP/220V/440V/60HZ/3 PHASE HEX BOLT 5/8”*2” FLAT WASHER 5/8”*OD40*3t HEX NUT 5/8” LOCK WASHER 5/8” BLOWER HEX BOLT 1/2”*1-1/2” FLAT WASHER 1/2”*OD28*3t HEX NUT 1/2” LOCK WASHER 1/2” PLUG 25*25 IMPELLER/FAN 26” FAN WASHER 1*OD58*3t 1-1/16”...
- Page 26 Part List Ref No Part Name Description Q’TY LOCK NUT 3/8” TOP BAG HOUSING HEX BOLT 3/8”*1” FLAT WASHER 3/8”*OD23*2t LOCK NUT 3/8” LOWER HOUSING HEX BOLT 3/8”*1” FLAT WASHER 3/8”*OD23*2t LOCK NUT 3/8” LEG STAND HEX BOLT 3/8”*3/4” FLAT WASHER 3/8”*OD23*2t EZ LIFT HANDLE SUPPORT BASE HEX BOLT...
- Page 27 Part List Ref No Part Name Description Q’TY Ø500 SPRING CLAMP DRUM LID THREADED BOLT 3/8”*7” FLAT WASHER 3/8”*OD23*2t LOCK NUT 3/8” SPRING Ø740mm*1.3M LOWER PLASTIC BAG 64 GALLON DRUM R-SHAPED GASKET 2.1M WINDOW FLAT WASHER 2.7*OD6*1.5t RIVET CASTER 4” HEX BOLT 5/16”*3/4”...
- Page 28 Part List Ref No Part Name Description Q’TY HEX BOLT 1/4”*3/4” FLAT WASHER 1/4”*OD19*2t LOCK NUT 1/4” TOP FILTER BAG SUPPORT ROD HEX BOLT 5/16”*3/4” TOP FILTER BAG UPPER FRAME BAG HANGER FLAT WASHER 3/8”*OD23*2t LOCK NUT 3/8” 30C-1 NUT 3/8”...
- Page 29 10HP Bag Filter Dust Collector Manual...
- Page 30 NOTE 10HP Bag Filter Dust Collector Manual...
- Page 31 NOTE 10HP Bag Filter Dust Collector Manual...
- Page 32 Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. © 2016, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.