XGIMI HORIZON Ultra Manual
Also See for HORIZON Ultra:

Advertisement

XGIMI HORIZON Ultra Manual

Overview

Rear view
Overview
Note:
An HDMI 21 cable should be used on the HDMI 21 port.

Remote control

  1. Power
  2. Settings
  3. Google Assistant
  4. Navigation
  5. Return
  6. Home
  7. VOL-
  8. VOL+
  9. Menu
  10. Focus

Getting Started

Power on/off

Connect to the power source, and press the power button on the back to turn on the device.
When the device is on, press the power button on the back to turn off the device.
Power on/off

Remote control pairing

Place the remote control within 10 cm of the device.
Press "" and "" simultaneously, and an indicator light will begin flashing as the remote control enters pairing mode. Release the buttons as soon as the flashing begins. The connection is successful when you hear a "Ding".
If pairing fails, repeat the above steps after 30 s.

Remote control functions

Focus adjustment function:
Short press the "" to enable autofocus.
Long press the "" to enable manual focus.

Shortcut button:
To access the shortcut button function, short-press the "".
To access all settings, press "".

Intelligent Screen Alignment

When Auto Keystone Correction is enabled, the display will be adjusted automatically to a square image whenever you move the device slightly or to another location. In addition, Auto Keystone Correction will not interfere with the projected content during the process, and the device will continue to work well on white, flat walls.
Intelligent Screen Alignment

Google Assistant

Google Assistant can be activated by pressing the "" button on the remote control.
Using your voice, you can quickly access entertainment, control smart devices, and get answers on screen.

Settings

Adjust device and image settings at any interface by pressing "" on the remote control. Specific functions for various settings are as follows:

Clear Apps Remove apps from the device
Keystone Correction Adjust the keystone for the projected image
Image Mode Adjust image parameters under the video or signal source
Sound Settings Adjust the device's voice output channel
3D Video Setup 3D settings for video and signal sources
Sleep Timer Automatically shut down the device after a pre-set time
All Settings Settings for other related functions
  • 3D mode and Image mode settings can only be adjusted via the video play or signal source channel.
  • Frame ratio and HDMI version settings can only be adjusted via the HDMI channel.

Chromecast built-in™

Cast your favorite entertainment apps-movies, TV shows, music, games, sports, and more—from your Android or iOS devices, Mac, Windows computer, or Chromebook to the device. Find Chromecast-enabled apps at g.co/castapps.
Quickly cast video and audio content to your TV by using "" on the supported mobile application. Screencasting will not be interrupted when you receive a call or message, and mobile phone battery consumption is minimal.
Entire frames on Android phones or Chrome browsers via PC can be cast to your TV.
Note:
Screencasting is optimized for selected services only. Streaming quality for other content might vary. Supported operating systems and devices: AndroidTM2.3 Gingerbread and higher, i0S® 7 and higher, Windows® 7 and higher, Mac OS.10.7 and higher and Chrome OS (version 38 or higher).

System upgrade

Online upgrade
The online upgrade can be made through system setting

Please refer to the information on the exterior bottom of the enclosure for electrical and safety information before installing or operating the apparatus.

Warning for remote controller and portal device

  • There is a risk of explosion if the battery is replaced with the wrong type of battery;
  • Disposal of a battery into fire, mechanically crushing or cutting the battery, may result in an explosion;
  • Do not leave battery in an environment with extremely high temperature that may result in an explosion or the leakage of flammable liquid or gas;
  • Do not put battery in an environment with extremely low pressure that may result in an explosion or the leakage of flammable liquid or gas.

Correct use of the device

  • Do not face lens into eyes as injury to the eyes can be caused by the strong projector light.
  • Do not block the air inlet/outlet of the device in order to avoid damage to internal electronic devices arising from normal heat dissipation failure of the device.
  • Do not wipe the lens directly with cleaning tools including paper and cloth etc. in order to avoid damage to lens; please clean up the dust on the lens surface through clean air blowing.
  • Do not wash the device with chemicals, detergents or any liquid in order to avoid corrosion of circuit board by rainwater, moisture and mineral-containing liquids.
  • Keep the device and its components and accessories out of reach of children.
  • Ensure that the device is used in a dry and ventilated environment.
  • Do not store the device in overheated or overcooled places because extreme temperatures will shorten the lifespan of electronic devices. Permissible storage and usage environments should have a temperature range of 0°C to 40°C.
  • Do not put the device into any heating equipment (such as a dryer or microwave oven) for drying.
  • Do not extrude the device firmly or place barriers on it or its back to avoid damage to the device.
  • Do not throw, strike, or sharply shake the device to avoid damage to the internal circuit board.
  • Do not try to disassemble and assemble the device yourself. Please contact XGIMI after-sales service for any issues.
  • Do not repair any product on your own. In the case of normal operation failure of the device or any component, consult XGIMI after-sales service promptly or return it to the factory for repair.
  • Operations in the 515-5.35 GHz band are restricted to indoor usage only.
  • When installing and operating the device, the distance between radiator and body should be at least 20cm.
  • As with any bright sources, do not stare directly into the beam, RG2 IEC 62471-5:2015
  • Complies with 21 CFR 104010 and 104011 except for conformance as a Risk Group 2 LIP as defined in IEC 62471-5:Ed. 1.0. For more information see Laser Notice No. 57, dated May 8, 2019.
  • Be cautious when using earphones with the device as there may be excessive sound pressure from earphones and headphones that can cause hearing loss.

VCSEL Laser
IEC 60825-1:2014
Max output of laser radiation: Max. 60 J
Pulse duration: 15 Hz
Emitted wavelength: 850 nm
Name and publication date of the standard: IEC 60825-1: 2014

Wi-Fi (5 GHz band) warning
High-gain directional antennas apply only to the fixed peer-to-peer networking. Do not place the device near radar systems.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download XGIMI HORIZON Ultra Manual

Advertisement

Need help?

Need help?

Do you have a question about the HORIZON Ultra and is the answer not in the manual?

Questions and answers

Table of Contents