Subscribe to Our Youtube Channel
Related Manuals for Planet VIP-410
Summary of Contents for Planet VIP-410
-
Page 1: Table Of Contents
Table of Contents Overview Document Objectives Document Organization Preparation before beginning administration on VIP-410 Physical Installation Administration Interface Web configuration access: CLI configuration access: LAN/WAN Interface quick configurations LAN IP configuration via command line interface (CLI) LAN IP address configuration via web configuration interface... -
Page 2: Overview
This quick installation guide describes the objectives, organization and basic installation of the PLANET VIP-410 voice gateway, and explains how to establish your first voice over IP communication via PLANET product. Also, this guide shows you how to find additional information on related products and services. -
Page 3: Administration Interface
· Microsoft Internet Explorer 4.01 or higher with Java support Default LAN interface IP address of VIP-410 is 192.168.0.1. You may now open your web browser, and insert 192.168.0.1 in the address bar of your web browser to logon VIP-410 web configuration page. -
Page 4: Cli Configuration Access
Nature of PLANET VIP-410 is an IP Sharing (NAT) device, it comes with two default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”. You may use any PC to connect to the LAN port of VIP-410 to start machine administration.,... -
Page 5: Lan Ip Configuration Via Command Line Interface (Cli)
IP of VIP-410 is the IP address for remote calling party to connect with. LAN IP configuration via command line interface (CLI) Here we’d like to configure the IP address of VIP-410 LAN interface, LAN IP address related commands are: ITG>net set lan net set lan ip <addr>... -
Page 6: Wan Ip Address Configuration Via Web Configuration Interface
Subnet Mask, LAN mask of VIP-410 Default: 255.255.255.0 DHCP server Config Number of DHCP VIP-410 is capable of working as a DHCP server, the DHCP client number is the Client allowed DHCP clients in VIP- 410’s network. Default: 30 Start address Beginning IP address of DHCP client IP assignment. -
Page 7: Internet Access Setup
If using a specified (fixed) IP address on your PC, refer to the user manual for details of the required changes: · The Gateway must be set to the IP address of VIP-410 · The DNS should be set to the address provided by your ISP. -
Page 8: Voice Communication Samples
0 (local port #1) 1 (local port #2) Base on this, if you have one VIP-410 with two FXS ports connect to two telephones, say port 3 and port 4, just pick up phone 1 and dial ‘204’, phone 2 should rings. -
Page 9: Vip To Vip
If you fail to hear the dial tone, please check line impedance of your PBX. For a VIP with FXO port, you should find a Guide Hint: about it in your package. Please set up as it told to adjust your FXO port. - Page 10 Dialplan setting on VIP A: ITG>atpm req ITG>atpm dadd 10 h323 172.16.0.2 ITG>atpm hadd 10 2 10 ITG>atpm aadd 02 0 5 10 2 ITG>atpm done ITG>atpm store Dialplan setting on VIP B: ITG>atpm req ITG>atpm dadd 10 h323 172.16.0.1 ITG>atpm hadd 10 2 10 ITG>atpm aadd 01 0 5 10 2 ITG>atpm done...
- Page 11 VIP A: Pick up handset and dial “02203”, where ‘02’ points to VIP B and ‘203’ for port 3 of VIP B. The phone in VIP B should rings. VIP B: Pick up handset and dial “01203”, where ‘01’ points to VIP A and ‘203’ for port 3 of VIP A.
-
Page 12: Quick Reference In Cd-Rom Guide
Quick reference in CD-ROM guide This guide is used to help you startup your VIP settings. It is also recommended to check the user manual CD-ROM for more details like the “Console Command”, “Web Setup”, and how to set the device back to default value. - Page 15 Part No.:EMQ_VIP410v1...
Need help?
Do you have a question about the VIP-410 and is the answer not in the manual?
Questions and answers