Table of Contents
Advertisement
The System Setup menu
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
System Setup menu (starting on page 44).
You can also choose to view the settings by selecting
individual parameters from the MCACC Data Check
screen:
• Speaker Setting – The size and number of speakers
you've connected (see page 56 for more on this)
• Channel Level – The overall balance of your speaker
system (see page 48 or 57 for more on this)
• Speaker Distance – The distance of your speakers
from the listening position (see page 49 or 58 for
2
more on this)
• Standing Wave – Filter settings to control lower
'boomy' frequencies (see page 50 for more on this)
• Acoustic Cal EQ – Adjustments to the frequency
balance of your speaker system based on the
acoustic characteristics of your room (see page 51
for more on this)
• FULL BAND PHASE CTRL – The original
characteristics of group delay of the speakers
calibrated and the targeted characteristics can be
displayed graphically (see Full Band Phase Control on
page 53 for more on this).
Press ENTER after you have finished checking each
screen. When you're finished, select RETURN to go back
to the System Setup menu.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC setup.
Note
1 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different size
settings. You can correct the setting manually using the Manual speaker setup on page 56.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and
room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend adjusting
the settings manually.
2 Since the distance measurements have been set according to the sound characteristics of your speakers, there are cases where (for optimal surround
sound) the actual distance may differ from the speaker distance setting.
3 • When changing the speaker output settings, we recommend selecting the speaker layout/usage pattern first.
• All the MCACC memory settings are cleared when the speaker output settings are changed. Perform the Auto MCACC Setup procedure again after
changing the speaker connections and speaker output settings (see page 12).
Speaker output setting
• Default setting: Normal
1
You can set the usage purpose for the ten channels worth
of speaker terminals. One of five patterns can be selected
according to the speaker layout and usage purpose (see
Selecting the speaker layout/usage pattern on page 10).
1
Select 'Output Setup' from the System Setup
menu.
See Making receiver settings from the System Setup menu
above if you're not already at this screen.
The receiver's volume is set to the minimum in order to
protect the speakers.
2
Select the speaker setting.
• Normal – Select for "Normal surround connections".
• All Ch Bi-Amp – Select for "5.2-channel high sound
quality connections".
• Front Bi-Amp – Select for "7.2-channel front high
sound quality connections".
• 7.2ch+ZONE 2 – Select for "7.2-channel + Zone 2
connections".
• 7.2ch+Speaker B – Select for "7.2-channel + speaker
B connections".
3
Select 'Confirm'.
The layout of the speaker terminals for the selected item
is displayed.
4
Check the layout of the output terminals, then
select 'YES'.
The setting is made according to the selected item.
5
When you're finished, press RETURN.
You will return to the System Setup menu.
DVD/L D
- 5 5 .0dB
DV D/LD
S y s te m S e tup ME NU
2. Output Setup
1 . Auto MCACC
2 . O utpu t Se tup
3 . Ma nua l MCACC
F ront
: Norma l
4 . FUL L BAND PHAS E CTRL
Ce n te r : Norma l
5 . Da ta Ma nag e me nt
S urr
: Array
6 . Ma nua l S P Se t up
S B
: Norma l
7 . Inp ut S e tup
8 . O SD L a nguag e
9 . O the r S e tup
[
Con firm
:E x it
3
- - . - dB
Norma l
]
:Cancel
07
47
En
Hide quick links:
Advertisement
Table of Contents
