A Shutdown Sequence; Using Multi Operations - Pioneer Elite SC-09TX Operating Instructions Manual

Controlling the rest of your system
13
Programming a multi-operation or a
shutdown sequence
Set the remote control operation mode selector switch to
RCV when you want to program this receiver's
operations, to SOURCE when you want to program
operations of other components.
MAIN
RECEIVER
ZONE2
DVD DVD BD BD
DVR1 DVR1 DVR2 DVR2
HOME MEDIA HOME MEDIA
GALLERY GALLERY CD CD
TUNER TUNER PHONO PHONO
XM XM SIRIUS SIRIUS
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows SETUP.
Use / to select MULTI OP or SYS OFF from the
2
menu and press ENTER.
If you selected Multi Operation (MULTI OP), the LCD on
the remote prompts you for an input source button.
If you selected System Off (SYS OFF), go to step 4.
3 Press the input source button for the component
that will start the multi-operation, then press ENTER.
For example, if you want to start the sequence by
switching on your DVD player, press DVD.
Use / to select CODE EDT, then press ENTER.
4
To erase any previously stored multi-operations (or
shutdown sequences) select CODE ERS above.
Use / to select a command in the sequence, then
5
press ENTER.
If this is the first command in the sequence, select 1ST
CODE. Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER.
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
116
En
SOURCE
TV CONTROL
3 INPUT MUTE MUTE
MULTI MULTI
AUDIO VIDEO
OPERATION OPERATION
PARAMETER PARAMETER
TUNE
TV TV SAT SAT
TOP MENU MENU
BAND T.EDIT
VIDEO1 VIDEO2 VIDEO1 VIDEO2
ST ST
ENTER Enter
SACD SACD CD-R CD-R
RETURN
SETUP SETUP
iPod iPod HDMI HDMI
TUNE
CATEGORY
INPUT SELECT INPUT SELECT
STATUS CH LEVEL
THX MPX MEMORY
7 Select the button for the command you want to
input.
The following remote control commands can be selected:
MAIN
RECEIVER SOURCE
ZONE2 3
MULTI
OPERATION
DVD BD TV SAT
DVR1 DVR2 VIDEO1 VIDEO2
HOME MEDIA
GALLERY CD SACD CD-R
TUNER PHONO iPod HDMI
INPUT SELECT
XM SIRIUS
SOURCE
TV RCV
CH VOL
VOL
TV CONTROL
INPUT MUTE MUTE
AUDIO VIDEO
• You don't need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components, you don't need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it's the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
8 Repeat steps 5 to 7 to program a sequence of up to
five commands.
When you're finished, use / to select EXIT from
9
the menu and press ENTER.
You will return to the remote control Setup menu. Select
* EXIT * again to exit.

Using multi operations

You can start multi operations with the receiver switched
on, or in standby.
MAIN
RECEIVER
ZONE2
DVD BD
DVR2
DVR1
HOME MEDIA
GALLERY CD
1 Press MULTI OPERATION.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
AUDIO VIDEO
PARAMETER PARAMETER
TUNE
TOP MENU MENU
BAND T.EDIT
ST ENTER ST
RETURN
SETUP
TUNE
CATEGORY
STATUS CH LEVEL
THX MPX MEMORY
AUTO/ STEREO/
F.S.SURR STANDARD ADV SURR
DIRECT
SIGNAL SEL SLEEP DIMMER AUDIO
SR+ SBch PHASE
iPod CTRL
DISP
A.ATT GENRE HDMI OUT
CH
D.ACCESS MCACC CLASS
ENTER
CLR
SOURCE
3
MULTI MULTI
OPERATION OPERATION
TV SAT
VIDEO1 VIDEO2
SACD CD-R