Table of Contents
Advertisement
Quick Links
Installation Instructions
Original Instructions
FLEX 5000 Analog 4-channel Isolated Current/Voltage/HART Safety Output Modules
Catalog Numbers 5094-OF4IHS, 5094-OF4IHSXT
Topic
Summary of Changes
This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.
Topic
Updated template
Updated trademarks
Updated UK and European Hazardous Location Approval
Updated IEC Hazardous Location Approval
Updated Special Conditions for Safe Use
Updated Module Specifications
Product Overview
The 5094-OF4IHS and 5094-OF4IHSXT analog 4-channel isolated current/voltage/HART safety output modules convert digital values to analog signals. The module offers output
channels that can connect to current, voltage or 4...20 mA HART output devices, and the module channels support multiple ranges for each output type.
FLEX 5000® I/O modules use the Producer/Consumer communication model. The Producer/Consumer communication model is an intelligent data exchange between modules and
other system devices in which each module produces data without first being polled.
The 5094-OF4IHS and 5094-OF4IHSXT modules can be used with GuardLogix® 5580 and Compact GuardLogix 5380 Safety controllers in applications up to SIL 3, PLe, Cat. 4. The
modules are configured with the Studio 5000 Logix Designer® application.
These safety modules are type-approved and certified for use in safety applications up to and including SIL 3 per IEC 61508, suitable for use in safety applications up to and
including SIL CL 3 per IEC 62061, and up to and including Performance Level PLe (Category 4) per ISO 13849-1.
For more information about safety application requirements and about which Logix 5000® controllers and Logix Designer application versions are compatible with
FLEX 5000 I/O modules, see the publications that are listed under
Page
4
5
5
6
7
8
9
10
10
10
11
11
Page
throughout
Additional Resources on page
11.
1
3
3
3
11
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rockwell Automation Allen-Bradley 5094-OF4IHS
Summary of Contents for Rockwell Automation Allen-Bradley 5094-OF4IHS
-
Page 1: Table Of Contents
Installation Instructions Original Instructions FLEX 5000 Analog 4-channel Isolated Current/Voltage/HART Safety Output Modules Catalog Numbers 5094-OF4IHS, 5094-OF4IHSXT Topic Page About the Module Before You Begin Required Components Install the Module Wire the Terminal Base Disconnect Wires from the Terminal Base Wiring Diagrams Power the System Remove the Module... - Page 2 WARNING: For Class I Division 2 applications, use only Class I Division 2 listed or recognized accessories and modules approved for use within the 5094 platform. When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the governing electrical codes. Rockwell Automation Publication 5094-IN017B-EN-P - August 2022...
- Page 3 The enclosure must be accessible only by the use of a tool. • This equipment shall be used within its specified ratings defined by Rockwell Automation. • Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment.
-
Page 4: About The Module
Any illustrations, charts, sample programs, and layout examples shown in this publication are intended solely for the purposes of example. Since there are many variables and requirements associated with any particular installation, Rockwell Automation does not assume responsibility or liability for actual use based upon the examples shown in this publication. -
Page 5: Before You Begin
The use of other DIN rail materials (for example, aluminum or plastic) that can corrode, oxidize, or are poor conductors, can result in improper or intermittent grounding. Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail properly. See Industrial Automation Wiring and Grounding Guidelines, Rockwell Automation publication 1770-4.1 for more information. -
Page 6: Power Considerations
You must install an end cap on the right side of the last terminal base in a FLEX 5000 I/O system. The end cap covers the exposed interconnections on the adapter or on the last terminal base in the system. If you do not install the end cap before powering the system, equipment damage or injury from electric shock can result. Rockwell Automation Publication 5094-IN017B-EN-P - August 2022... -
Page 7: Wire The Terminal Base
(22…16 AWG) = Strip 10 mm ± 1 mm (0.39 in ± 0.04 in) of insulation from the wires Spring 2.5 mm (14 AWG) = Strip 15 mm ± 1 mm (0.59 in ± 0.04 in) of insulation from the wires Rockwell Automation Publication 5094-IN017B-EN-P - August 2022... -
Page 8: Disconnect Wires From The Terminal Base
1. Turn the screwdriver counter-clockwise to open the terminal. Screw 2. Remove the wire. 1. Insert and hold a screwdriver in the slot above the terminal. Spring 2. Remove the wire. 3. Pull out the screwdriver. Screw-type TB Spring-type TB Rockwell Automation Publication 5094-IN017B-EN-P - August 2022... -
Page 9: Wiring Diagrams
5094-OF4IHS and 5094-OF4IHSXT Wiring Diagram - 2- or 4-wire Voltage Actuator 4-wire voltage actuator external powered – SA– SA– 2-wire voltage actuator – AC/DC PSU2 Do not wire AC power directly to the module. Shield Bar Rockwell Automation Publication 5094-IN017B-EN-P - August 2022... -
Page 10: Power The System
Be sure to press the entire lever evenly. Pull the module off the terminal base. Replace the Module To replace the module, follow the steps that are described beginning at Install the Module on page Rockwell Automation Publication 5094-IN017B-EN-P - August 2022... -
Page 11: Module Specifications
Provides specifications for the shield bar and jumper accessories. Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system. Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other certification details. -
Page 12: Rockwell Automation Support
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur Connect with us. Allen-Bradley, expanding human possibility, FactoryTalk, FLEX 5000, GuardLogix, Logix 5000, Rockwell Automation, Studio 5000 Logix Designer, and TechConnect are trademarks of Rockwell Automation, Inc EtherNet/IP is a trademark of ODVA, Inc Trademarks not belonging to Rockwell Automation are property of their respective companies.
Need help?
Do you have a question about the Allen-Bradley 5094-OF4IHS and is the answer not in the manual?
Questions and answers