Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ranger design 3010-FTL
Summary of Contents for Ranger design 3010-FTL
- Page 1 INSTALLATION GUIDE 3010-FTL CONTOURED PARTITION Transit Partition ( Aluminum )
-
Page 2: Table Of Contents
3/8" Drill Bit q 7/16" Socket q 1/2" Socket q 9/16" Wrench q 1" Hole Saw PERSONS q 10mm Socket q 13mm Socket 3010-FTL Installation Guide | REV. D2 | Page 2 For technical support, contact us at 1-800-565-5321... -
Page 3: Phase 1 - Assembly
Driver Side Wing 30-036 Lower Panel 30-500 Edge Trim ( QTY in Inches ) 79-932 Bilingual Warning Label 94-3011 Assembly Fastener Bag 96-3005 Installation Fastener Bag 3010-FTL Installation Guide | REV. D2 | Page 3 For technical support, contact us at 1-800-565-5321... -
Page 4: Hardware Assembly
# 98-157 0.375" ID, × 1.0" OD × 0.25" LONG NYLON 2× Retaining Washer 4× # 98-158 M16 ( 1/4") #98-141 Square Flat Washer NYLON 3010-FTL Installation Guide | REV. D2 | Page 4 For technical support, contact us at 1-800-565-5321... -
Page 5: Q 1.2 Partition Assembly
1.2.2 Attach both wings to the upper and lower panels. TOOLS q Cordless Impact q 1/2" Socket HARDWARE USED 16× #90-484 Carriage Bolt 5/16" × 5/8" #94-116 Serrated Nut 3010-FTL Installation Guide | REV. D2 | Page 5 For technical support, contact us at 1-800-565-5321... -
Page 6: Q 1.2.3 Attach The Edge Trims On These Locations
TIPS: Put the plusnut on the plusnut gun, then attach the plusnut in the hole by turning the gun forward until the plusnut locks, then remove the gun by turning in reverse. FORWARD REVERSE 3010-FTL Installation Guide | REV. D2 | Page 6 For technical support, contact us at 1-800-565-5321... -
Page 7: Q 2.1.2 Attach Plusnut Using 6490 Plusnut Tool
7/16" socket until the plusnut locks, then remove the bolt by turning the impact in reverse. FORWARD REVERSE 3010-FTL Installation Guide | REV. D2 | Page 7 For technical support, contact us at 1-800-565-5321... -
Page 8: Q 2.2 Vehicle Preparation
(Use caution not to damage the threaded holes). q Plusnut Tool TOOLS HARDWARE USED q 1" Hole Saw 2× q Cordless Drill # 94-130 Plusnut .250 3010-FTL Installation Guide | REV. D2 | Page 8 For technical support, contact us at 1-800-565-5321... -
Page 9: Q 2.2.2 Floor Preparation
2 D-ring bolts with the addition of the square washers, in between the D-rings and floor bracket. TOOLS q Socket Wrench q 13mm Socket HARDWARE USED 2× 3010-FTL Installation Guide | REV. D2 | Page 9 For technical support, contact us at 1-800-565-5321... -
Page 10: Q 2.3.2 Attach The Passenger Side Wing To The Van
#98-158 Retaining washer Attach the passenger side wing using the 2 metric bolts into the 2 threaded holes. TOOLS q Cordless Impact q 10mm Socket 3010-FTL Installation Guide | REV. D2 | Page 10 For technical support, contact us at 1-800-565-5321... -
Page 11: Q 2.3.3 Attach The Driver Side Wing To The Van
#98-157 Spacers ( 2 ) #98-158 Retaining Washer Attach the driver side wing using the hex bolts into the 2 plusnuts. TOOLS q Socket Wrench q 7/16" Socket 3010-FTL Installation Guide | REV. D2 | Page 11 For technical support, contact us at 1-800-565-5321... -
Page 12: Q 2.3.4 Attach The Lower Panel To The Floor Bracket
2.3.4 Attach the lower panel to the floor bracket. TOOLS q Cordless Impact q 1/2" Socket HARDWARE USED 4× #90-484 Carriage Bolt 5/16" × 5/8" #94-116 Serrated Nut 3010-FTL Installation Guide | REV. D2 | Page 12 For technical support, contact us at 1-800-565-5321... -
Page 13: Q 2.3.5 Apply The Warning Label On The Passenger Side Wing
2.3.5 Apply the warning label on the passenger side wing. NOTE: English warning label is already attached on the passenger side panel. 3010-FTL Installation Guide | REV. D2 | Page 13 For technical support, contact us at 1-800-565-5321... - Page 14 “Congratulations, you have successfully installed your Contoured Partition! Thank you for doing business with us.” 3010-FTL Installation Guide | REV. D2 | Page 14 For technical support, contact us at 1-800-565-5321...
Need help?
Do you have a question about the 3010-FTL and is the answer not in the manual?
Questions and answers