Page 1 User Manual Nighthawk WiFi 7 Dual-Band Router Model RS200 and Model RS150v1 NETGEAR, Inc. September 2024 350 E. Plumeria Drive 202-12737-01 San Jose, CA 95134, USA...
Page 2 See the regulatory compliance document before connecting the power supply. For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy. By using this device, you are agreeing to NETGEAR’s Terms and Conditions at https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the device to your place of purchase within your return period.
Page 3: Table Of Contents
Contents Chapter 1 Introduction What is WiFi 7?.................. 11 Additional documentation............... 11 Chapter 2 Hardware Setup Unpack your router................13 Front panel LEDs and buttons............13 Rear panel..................16 Router label..................17 Position your router................18 Cable your router................19 Chapter 3 Connect to the Router Network and Access the Router Connect to the router network............
Page 4 MTU concepts................50 Change the MTU size..............51 Chapter 5 Control Access to the Internet NETGEAR Armor................54 Activate Armor using the Nighthawk app........54 Network access control list.............. 54 Enable the network access control list, set the access rule, and allow or block connected devices..........
Page 5 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Enable or disable PMF..............84 Enable or disable airtime fairness..........85 Change the CTS/RTS threshold or preamble mode for a radio....................86 Use the WPS Wizard for WiFi connections........87 Use the WPS Wizard with the push button....... 87 Use the WPS Wizard with a PIN..........
Page 6 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manually upload firmware to the router ......... 117 Manage the firmware update settings........118 Change the admin password............118 Enable admin password reset............119 Reset the admin password............120 Use HTTPS to access the router............ 121 Change the router’s device name..........
Page 7 Set up and manage Dynamic DNS..........155 Set up a new Dynamic DNS account........155 Use a Dynamic DNS account that you already have....156 Manage your existing NETGEAR or No-IP Dynamic DNS account..................157 Your personal FTP server............... 158 Set up your personal FTP server: Overview of steps.....
Page 8 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Add a port triggering rule............179 Change a port triggering rule..........180 Remove a port triggering rule..........181 Set the time-out period for port triggering......182 Disable an individual port triggering rule....... 182 Disable port triggering..............
Page 9: Chapter 1 Introduction
NOTE: Firmware updates with new features and bug fixes are made available from time to time at netgear.com/support/download/. You can check for and download new firmware manually. If the features or behavior of your product does not match what is described in this manual, you might need to update the firmware.
Page 10 NOTE: In this manual, WiFi network means the same thing as SSID (service set identifier or WiFi network name) or VAP (virtual access point). That is, when we refer to a WiFi network we mean an individual SSID or VAP.
Page 11: What Is Wifi 7
• 2.4 times faster speed than WiFi 6 • Double the maximum bandwidth for your devices • Lower latency than WiFi6 • A more reliable connection For more information, visit the NETGEAR WiFi 7 page at netgear.com/home/discover/wifi7. Additional documentation The following documents are available at netgear.com/support/download/: •...
Page 12: Chapter 2 Hardware Setup
• Unpack your router • Front panel LEDs and buttons • Rear panel • Router label • Position your router • Cable your router For more information about the topics covered in this manual, visit the support website at netgear.com/support.
Page 13: Unpack Your Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Unpack your router Your package contains the router, an Ethernet cable, and the power adapter (the type varies by region). Figure 1. Package contents Front panel LEDs and buttons The status LEDs and two buttons are located on the front panel of the router. Hardware Setup User Manual...
Page 14 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Figure 2. Top view Table 1. LED descriptions LED and Button Description Power LED Solid white: The router is ready. Solid amber and then blinking amber: The Reset button was pressed. When you first press the Reset button, the LED lights solid amber.
Page 15 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Table 1. LED descriptions (Continued) LED and Button Description Ethernet LAN ports 1–4 The LED color indicates the speed of the Ethernet connection at each LAN port: LEDs white for the maximum supported speed on each port (2.5 Gbps on port 1, 1 Gbps on ports 2-4) and amber for lower speeds.
Page 16: Rear Panel
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Rear panel The following figure shows the rear panel connectors and buttons. Figure 3. Rear panel The rear panel contains the following components: • A. Reset button: Pressing the Reset button resets the router. If the Reset button is pressed for at least five seconds and the Power LED blinks amber, the router returns to its factory settings.
Page 17: Router Label
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • C. 2.5G LAN port: One RJ-45 LAN port that supports speeds up to 2.5 Gbps. Use a Category 5e (Cat5e) Ethernet cable or higher rated Ethernet cable to connect the router to a high-speed LAN server, LAN storage device, or another LAN device.
Page 18: Position Your Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Figure 4. Router label Position your router The router lets you access your network anywhere within the operating range of your WiFi network. However, the operating distance or range of your WiFi connection can vary significantly depending on the physical placement of your router.
Page 19: Cable Your Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • To avoid wireless signal interference, place the router away from electrical devices such as these: ○ Ceiling fans ○ Home security systems ○ Microwaves ○ Computers ○ The base of a cordless phone ○...
Page 20 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Figure 5. Cable your router To cable your router: 1. Unplug your modem, remove and reinsert the backup battery if it uses one, and then plug the modem back in. 2. Use the Ethernet cable to connect the modem to the yellow Internet port on the router.
Page 21: Chapter 3 Connect To The Router Network And Access The Router
Connect to the Router Network and Access the Router You can connect to the router’s WiFi networks or use a wired Ethernet connection. This chapter explains the ways you can connect and how to access the router and log in. The chapter contains the following sections: •...
Page 22: Connect To The Router Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Connect to the router network You can connect to the router network using a wired or WiFi connection. NOTE: If you set up your computer to use a static IP address, change the settings so that it uses Dynamic Host Configuration Protocol (DHCP).
Page 23: Types Of Logins
WiFi access. This information is on the router label. The WiFi password is also known as the network key or passphrase. • NETGEAR account login: The free NETGEAR account that you need to register your router, manage your router remotely, and manage your subscriptions. If you do not have a NETGEAR account, you can create one.
Page 24 Internet. When you start an Internet application, your router automatically logs you in. The NETGEAR installation assistant runs on any device with a web browser. Installation and basic setup takes about 15 minutes to complete.
Page 25: Log In To The Router After You Set Up The Router
2. If the router still does not detect the Internet settings, contact your ISP to verify that you are using the correct configuration information. 3. If problems persist, register your router and contact NETGEAR Technical Support. Log in to the router after you set up the...
Page 26: Change The Language
WiFi network, and helps you to register your router with NETGEAR. You can also manage your router remotely and use the Armor and Smart Parental Controls services.
Page 27 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The Nighthawk app is available for iOS and Android mobile devices. NOTE: Your router is not connected to the Internet until you finish setting it up with the app. If you are connected to your router’s WiFi network before your router is set up, you do not have Internet access and cannot download the app.
Page 28: Chapter 4 Specify Your Internet Settings
Usually, the quickest way to set up the router to use your Internet connection is to allow the NETGEAR installation assistant to detect the Internet connection. After you set up your router, you can use the Setup Wizard to redetect the Internet settings, or you can manually specify your Internet settings.
Page 29: Use The Setup Wizard
2. If the router still does not detect the Internet settings, contact your ISP to verify that you are using the correct configuration information. 3. If problems persist, register your router and contact NETGEAR Technical Support. Specify Your Internet Settings...
Page 30: Manually Set Up The Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manually set up the Internet connection You can view or change the router’s Internet connection settings. Set an Internet connection without a login You can manually specify the connection settings for an Internet service for which you do not need to log in.
Page 31 12. Click the Apply button. Your settings are saved. 13. Click the Test button to test your Internet connection. If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191. Specify Your Internet Settings...
Page 32: Set A Pppoe Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set a PPPoE Internet connection You can manually set the connection settings for a PPPoE Internet service for which you must log in. Use the information that your ISP gave you to connect to your Internet service.
Page 33: Set A Pptp Or L2Tp Internet Connection
Your settings are saved. 17. Click the Test button to test your Internet connection. If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191. Set a PPTP or L2TP Internet connection You can manually specify the connection settings for a PPTP or L2TP Internet service for which you must log in.
Page 34 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To set a PPTP or L2TP Internet connection: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3.
Page 35: About High-Speed Internet Connections And Internet Port Aggregation
15. Click the Apply button. Your settings are saved. 16. Click the Test button to test your Internet connection. If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191. About high-speed Internet connections and Internet port aggregation Use the router’s yellow Internet port, which supports speeds up to 2.5 Gbps, to connect...
Page 36: Get Multi-Gigabit Internet With Internet Port Aggregation
• A modem that support both an Internet speed that’s over 1 Gbps and two Ethernet ports that support static Link Aggregation Control Protocol (LACP), for example, the NETGEAR Nighthawk Multi-Gig Cable Modem, model CM1200. To set up Internet port aggregation: 1.
Page 37: Set An Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 7. Click the Apply button. Your settings are saved. 8. Connect the yellow Internet port and the Ethernet LAN port 4 on your router to two Ethernet ports on your modem. Set an IPv6 Internet connection The router supports many different types of IPv6 Internet connections for which you can specify the settings manually.
Page 38: Requirements For Entering Ipv6 Addresses
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Requirements for entering IPv6 addresses IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by colons. You can reduce any four-digit group of zeros within an IPv6 address to a single zero or omit it.
Page 39: Set A 6To4 Tunnel Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Connection Type: This field indicates the connection type that is detected. • Router’s IPv6 Address on WAN: This field shows the IPv6 address that is acquired for the router’s WAN (or Internet) interface. The number after the slash (/) is the length of the prefix, which is also indicated by the underline (_) under the IPv6 address.
Page 40 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To set a 6to4 tunnel IPv6 Internet connection: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3.
Page 41: Set A Pass-Through Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN). 9. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.
Page 42: Set A Fixed Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set a fixed IPv6 Internet connection To set a fixed IPv6 Internet connection: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2.
Page 43: Set A Dhcp Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 This selection enables RIP Next Generation (RIPng) on IPv6 Internet connections. RIPng is an extension of Routing Information Protocol (RIP) that supports IPv6. You might want to enable RIPng if you are an advanced user with a complex home network configuration that requires dynamic routing.
Page 44 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Most people can leave this field blank, but if your ISP gave you a specific host name, enter it here. 7. (Optional) In the Domain Name (If Required) field, enter a domain name. You can type the domain name of your IPv6 ISP.
Page 45: Set A Pppoe Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set a PPPoE IPv6 Internet connection To set a PPPoE IPv6 Internet connection: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2.
Page 46 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NOTE: The default setting of the Connection Mode menu is Always On to provide a steady IPv6 connection. The router never terminates the connection. If the connection is terminated - for example, when the modem is turned off - the router attempts to reestablish the connection immediately after the PPPoE connection becomes available again.
Page 47: Use Auto Config For An Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Use auto config for an IPv6 Internet connection To set up an IPv6 Internet connection through auto configuration: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 48: Set A 6Rd Ipv6 Internet Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers. Your ISP automatically assigns this address. Unless the ISP assigns DNS servers through DHCPv6, this option uses the DNS servers assigned by the ISP for the IPv4 connection.
Page 49 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 uses the 6rd option information to establish the 6rd connection. For more information, see Use auto detect for an IPv6 Internet connection on page 38. • Manual mode: In 6rd mode, if the router receives option 212, the fields are automatically completed.
Page 50: Manage The Mtu Size
“fragmented” to accommodate the device with the smallest MTU. The best MTU setting for NETGEAR equipment is often the default value. In some situations, changing the value fixes one problem but causes another. Leave the MTU...
Page 51: Change The Mtu Size
Table 2. Common MTU sizes Application 1500 The largest Ethernet packet size. This setting is typical for connections that do not use PPPoE or VPN and is the default value for NETGEAR routers, adapters, and switches. 1492 Used in PPPoE environments. 1472 Maximum size to use for pinging.
Page 52 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 4. Select ADVANCED > Setup > WAN Setup. The WAN Setup page displays. 5. In the MTU Size field, enter a value from 616 to 1500. 6.
Page 53: Chapter 5 Control Access To The Internet
The router comes with a built-in firewall that helps protect your home network from unwanted intrusions from the Internet. This chapter contains the following sections: • NETGEAR Armor • Activate Armor using the Nighthawk app • Network access control list •...
Page 54: Netgear Armor
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NETGEAR Armor Your router supports NETGEAR Armor. After you start your subscription, NETGEAR Armor protects your home network from potential cyber threats and provides complete data protection, advanced threat defense, webcam protection, multilayer ransomware protection, anti-phishing, safe files, secure browsing, rescue mode, anti-fraud, and anti-theft.
Page 55: Enable The Network Access Control List, Set The Access Rule, And Allow Or Block Connected Devices
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The router detects and stores the MAC addresses of devices that connect to the network, so it lists the MAC addresses both of devices that are currently connected and any that were previously connected.
Page 56 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 57: Manage Allowed Devices Currently Not On The Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NOTE: If you blocked all new devices from connecting, make sure that the computer or mobile device that you are currently using to access the router web interface shows as Allowed in the Status column. •...
Page 58 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 A table displays the detected device name, MAC address, and connection type of the devices that are not connected but allowed to access the network. In the following steps, we refer to the list of allowed devices not currently connected to the network as the list of allowed devices.
Page 59: Manage Blocked Devices Currently Not On The Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manage blocked devices currently not on the network If you set up an access control list (ACL) that allows all new devices to access the network, you can add new devices that must be blocked from accessing the network, remove old devices, or change whether devices that were blocked must now be allowed when they try to connect to the network.
Page 60: Block Internet Sites And Services
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The device is removed from the list of blocked devices. 8. To change the device status by allowing access for a device on the list of blocked devices, do the following: a.
Page 61 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To block Internet sites: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3. Enter the router admin user name and password. The user name is admin.
Page 62: Delete Keywords From The Blocked List
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Delete keywords from the blocked list To delete keywords from the list: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays.
Page 63: Block Services From The Internet
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 4. Select ADVANCED > Security > Block Sites. The Block Sites page displays. 5. Scroll down and select the Allow trusted IP address to visit blocked sites check box.
Page 64: Schedule When To Block Internet Sites And Services
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 7. To add a service that is in the Service Type menu, select the application or service. The settings for this service automatically display in the fields. 8. To add a service or application that is not in the menu, select User Defined, and do the following: a.
Page 65: Set Up Security Event Email Notifications
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The Schedule page displays. 5. Specify when the schedule is active: • Days to Block: Select the check box for each day that you want to enable blocking, or select the Every Day check box, which automatically selects the check boxes for all days.
Page 66 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 9. In the Your Outgoing Mail Server field, type the name of your ISP outgoing (SMTP) mail server (such as mail.myISP.com). You might be able to find this information in the configuration window of your email program.
Page 67: Chapter 6 Manage Wifi Settings
Manage WiFi Settings You can customize the router’s WiFi settings. The chapter includes the following sections: • Change the name for a WiFi network • Change the WiFi password or the WiFi security option • Set up WPA/WPA2 Enterprise WiFi security •...
Page 68: Change The Name For A Wifi Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Change the name for a WiFi network For each WiFi network, the WiFi network name (also referred to as the SSID) is randomly generated and is on the router label. You can change the default network name. The network name can be up to 32 characters long and is case-sensitive.
Page 69 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To change the WiFi password or the WiFi security option: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays.
Page 70: Set Up Wpa/Wpa2 Enterprise Wifi Security
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • WPA/WPA2 Enterprise: Requires that your WiFi network can access a RADIUS server. For more information, see Set up WPA/WPA2 Enterprise WiFi security on page 70. • WPA3-PSK: The default setting, which enables WiFi devices that support WPA3 to join the WiFi network.
Page 71: Hide Or Broadcast The Ssid For A Wifi Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 4. Select Wireless. The Wireless Setup page displays. 5. For the 2.4 GHz or 5 GHz WiFi network, select the WPA/WPA2 Enterprise radio button: 6. Specify the following settings: • Encryption mode: From the Encryption Mode menu, select the enterprise mode: ○...
Page 72: Enable Or Disable Ax Wifi
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 73: Enable Or Disable Ofdma
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Your settings are saved. Enable or disable OFDMA If AX WiFi is enabled (which it is by default), you can enable Orthogonal Frequency-Division Multiple-Access (OFDMA) for each radio band independently. By default, OFDMA is disabled in both radio bands, even when AX WiFi is enabled.
Page 74: Enable Or Disable Smart Connect
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Your settings are saved. Enable or disable Smart Connect Smart Connect selects the fastest WiFi band for your router. For Smart Connect to work, the 2.4 GHz and 5 GHz bands must use the same WiFi network name (SSID) and network key (password).
Page 75: Change The Wifi Mode
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 prevent interference between WiFi networks in your environment at the expense of WiFi speed. If no other WiFi networks are present in your environment, you can disable 20/40 MHz coexistence to increase the WiFi speed on the 2.4 GHz radio to the maximum supported speed for the WiFi mode.
Page 76 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 77: Change The Wifi Mode If Ax Wifi Is Disabled
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Change the WiFi mode if AX WiFi is disabled To change the WiFi mode settings if AX WiFi is disabled: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 78: Change The 2.4 Ghz Or 5 Ghz Wifi Channel
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 devices to function at up to 866 Mbps. This mode is the default mode if AX WiFi is disabled. 7. Click the Apply button. Your settings are saved. Change the 2.4 GHz or 5 GHz WiFi channel You can change the 2.4 GHz or 5 GHz WiFi channel.
Page 79: Change Your Country Or Region
54 Mbps mode in the 2.4 GHz band. The channel also depends on the channel selection of the main WiFi network. The router provides two default guest WiFi networks with the following names (SSIDs): • 2.4 GHz guest WiFi network SSID: NETGEAR-Guest • 5 GHz guest WiFi network SSID: NETGEAR-5G-Guest Manage WiFi Settings...
Page 80 • Guest Wireless Network Name (SSID): The SSID is the 2.4 GHz or 5 GHz guest WiFi network name. The default 2.4 GHz SSID is NETGEAR-Guest. The default 5 GHz SSID is NETGEAR-5G-Guest.
Page 81: Manage Advanced Wifi Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To use WPA2 security, in the Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the guest WiFi network, a user must enter this password. • WPA-PSK [TKIP] + WPA2-PSK [AES]: Enables WiFi devices that support either WPA or WPA2 to join the guest WiFi network.
Page 82: Set Up A Wifi Schedule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To enable or disable a WiFi radio: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3.
Page 83: Enable Or Disable Implicit Beamforming
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 5. Click the Add a new period button for a radio. The Turn off wireless signal by schedule page displays. 6. Use the menus, radio buttons, and check boxes to set up a period during which you want to turn off the WiFi signal.
Page 84: Enable Or Disable Mu-Mimo
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Your settings are saved. Enable or disable MU-MIMO Multiuser multiple input, multiple output (MU-MIMO) improves performance when many WiFi clients that are MU-MIMO-capable transfer data at the same time. For MU-MIMO to function, WiFi clients must support MU-MIMO (some older devices do not), and they must be connected to the 5 GHz WiFi band.
Page 85: Enable Or Disable Airtime Fairness
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 A login window displays. 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 86: Change The Cts/Rts Threshold Or Preamble Mode For A Radio
CAUTION: We recommend that you do not change these settings unless directed by NETGEAR support or unless you are sure what the consequences are. Incorrect settings might disable the WiFi function of a radio unexpectedly. NOTE: If the Smart Connect feature is enabled, the CTS/RTS threshold and preamble mode apply to all radios.
Page 87: Use The Wps Wizard For Wifi Connections
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 CAUTION: Incorrect settings might disable the radio’s WiFi broadcast unexpectedly. 7. Click the Apply button. Your settings are saved. Use the WPS Wizard for WiFi connections WPS (Wi-Fi Protected Setup) lets you connect a WPS-enabled device to your WiFi network without typing the WiFi password.
Page 88: Use The Wps Wizard With A Pin
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 By default, the Push Button (recommended) radio button is selected. 6. Click the green WPS software button on the page. 7. Within two minutes, go to the WPS-enabled device and use its WPS software to connect to the WiFi network.
Page 89: Chapter 7 Manage The Wan And Lan Network Settings
Manage the WAN and LAN Network Settings You can customize the router’s wide area network (WAN) settings for the Internet port and local area network (LAN) settings for local devices. We recommend that you install the router and connect it to the Internet before you change its network settings. This chapter contains the following sections: •...
Page 90: Manage The Wan Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manage the WAN settings You can change security and other settings that determine how the router interacts with the Internet, also known as the wide area network (WAN). Change the WAN security settings The wide area network (WAN) security settings include port scan protection and denial of service (DoS) protection, which can protect your local area network (LAN) against many common cyber attacks.
Page 91: Set Up A Default Dmz Server
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set up a default DMZ server The default DMZ server feature is helpful when you are using some online games and videoconferencing applications that are incompatible with Network Address Translation (NAT). The router is programmed to recognize some of these applications and to work correctly with them, but other applications might not function well.
Page 92: Manage Igmp Proxying
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manage IGMP proxying IGMP proxying allows a computer on the local area network (LAN) to receive the multicast traffic (such as video streaming) it is interested in from the Internet. If you do not need this feature, leave it disabled, which is the default setting.
Page 93: Manage The Sip Application-Level Gateway
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays. 4.
Page 94: Change The Lan Ip Address Settings Or Rip Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Your settings are saved. Change the LAN IP address settings or RIP settings The router is preconfigured to use private IP addresses on the local area network (LAN) side and to act as a Dynamic Host Configuration Protocol (DHCP) server. We also refer to the LAN IP address settings as the LAN TCP/IP settings.
Page 95: Set The Ip Addresses That The Router Assigns
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The IP address and subnet mask specify the IP address range that the devices on your network can use. 6. To change the RIP settings, do the following: a. Select the RIP direction: •...
Page 96: Disable The Dhcp Server Feature In The Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To set the pool of IP addresses that the router assigns: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays.
Page 97: Manage Reserved Lan Ip Addresses
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To disable the DHCP server feature in the router: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3.
Page 98: Edit A Reserved Ip Address
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 4. Select ADVANCED > Setup > LAN Setup. The LAN Setup page displays. 5. In the Address Reservation section, click the Add button. The Address Reservation page displays. 6.
Page 99: Delete A Reserved Ip Address Entry
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 5. Select the radio button next to the reserved address that you want to edit. 6. Click the Edit button. The Address Reservation page displays. 7. Change the settings. 8. Click the Apply button. Your settings are saved.
Page 100: Set Up A Static Route
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Your LAN subnet is 192.168.1.0, and the ADSL router’s address on your LAN is 192.168.1.100. • The public IP address range at the remote office site is 134.177.0.0. When you set up your router, two implicit static routes were created: 1.
Page 101: Edit A Static Route
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The Static Routes page displays. 5. Click the Add button. Static route configuration options display. 6. In the Route Name field, type a name for this static route (for identification purposes only).
Page 102: Delete A Static Route
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 4. Select ADVANCED > Advanced Setup > Static Routes. The Static Routes page displays. 5. In the table, select the radio button for the route. 6. Click the Edit button. Static route configuration options display.
Page 103: Set Up A Bridge For A Port Group
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Some devices, such as an IPTV, cannot function behind the router’s network address translation (NAT) service or firewall. For example, an IPTV port might require an IP address within the Internet service provider’s (ISP’s) network (also called an ISP intranet address).
Page 104: Set Up A Bridge For A Vlan Tag Group
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 7. Select a Wired Ports check box or a Wireless check box: • Wired Ports: If your device is connected to an Ethernet LAN port on the router, select the Wired Ports check box that corresponds to the Ethernet LAN port on the router to which the device is connected.
Page 105: Manage Ethernet Lan Port Aggregation To A Lan Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 5. Select the Enable VLAN / Bridge Settings check box. The page expands. 6. Select the Enable VLAN Tag radio button. The page expands. The table includes a default VLAN enabled for normal Internet access. The VLAN's ID is 10 and has all Ethernet LAN ports and WiFi networks as members.
Page 106: Set Up Lan Port Aggregation To A Lan Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To set up Ethernet LAN port aggregation to a LAN device that is configured for 802.3ad Link Aggregation Control Protocol (LACP), first configure Ethernet LAN port aggregation for the LAN port 1 and LAN port 2 on your router, and then connect these ports to the two aggregated ports on the LAN device.
Page 107: View Or Change The Router Lan Port Aggregation Mode
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Enable (LACP-IEEE 802.3ad): After you connect the Ethernet cables (see the following step), the router communicates with the LAN device that is connected to LAN ports 1 and 2 on your router, and checks to see if LAN port aggregation is supported on the LAN device.
Page 108 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 5. To change the LAN port aggregation mode, select one of the following radio buttons: • Disable: This mode is selected by default. This mode disables LAN port aggregation on your router. LAN ports 1 and 2 can be used as independent Ethernet LAN ports.
Page 109: Chapter 8 Optimize Performance
Optimize Performance You can set up the router to optimize performance. This chapter contains the following sections: • Enable QoS • Set the Internet bandwidth for your router • Update the QoS database • Manage Wi-Fi Multimedia QoS • Improve network connections with Universal Plug and Play...
Page 110: Enable Qos
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Enable QoS Quality of Service (QoS) helps improve your router’s Internet traffic management capabilities through better application and device identification, bandwidth allocation, and traffic prioritization techniques. QoS resolves traffic congestion when the Internet bandwidth is limited and different demands compete for bandwidth.
Page 111: Update The Qos Database
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 A login window displays. 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 112: Manage Wi-Fi Multimedia Qos
When you enable QOS, this check box is automatically selected. 6. To update the QoS database immediately, click the Update Now button. The router connects to a Netgear server. 7. Click the Apply button. Your settings are saved.
Page 113: Improve Network Connections With Universal Plug And Play
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 4. Select ADVANCED > Setup > QoS Setup. The QoS page displays. 5. Click the WMM tab. The WMM check boxes display. 6. Clear the Enable WMM (Wi-Fi multimedia) settings check box for one or more radios.
Page 114 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 6. In the Advertisement Period field, type the advertisement period in minutes. The advertisement period specifies how often the router broadcasts its UPnP information. This value can range from 1 to 1440 minutes. The default period is 30 minutes.
Page 115: Chapter 9 Manage And Monitor Your Router
Manage and Monitor Your Router This chapter describes the router settings for administering, maintaining, and monitoring your router and home network. This chapter contains the following sections: • Update the router firmware • Change the admin password • Enable admin password reset •...
Page 116: Update The Router Firmware
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Update the router firmware You can log in to the router and check if new firmware is available, or you can manually install a specific firmware version on your router. Check for new firmware and update the router The router firmware (routing software) is stored in flash memory.
Page 117: Manually Upload Firmware To The Router
Ethernet connection to upload the firmware. To manually upload a firmware file to your router: 1. Download the firmware for your router from the NETGEAR Download Center, save it to your desktop, and unzip the file if needed. NOTE: The correct firmware file uses an .img or .chk extension.
Page 118: Manage The Firmware Update Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 When the upload is complete, your router restarts. The upload process typically takes about one minute. Manage the firmware update settings You can set the router to automatically update to future firmware versions as they become available.
Page 119: Enable Admin Password Reset
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NOTE: The ideal password contains no dictionary words from any language and contains uppercase and lowercase letters, numbers, and symbols. It can be up to 30 characters. To change the password for the admin user name: 1.
Page 120: Reset The Admin Password
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The Set Password page displays. 5. Select the Enable Password Reset check box. 6. Select two security questions and provide answers to them. 7. Click the Apply button. Your settings are saved. Reset the admin password If you set up the password reset feature (see Enable admin password reset on page 119), you can reset your router admin password if you forgot it.
Page 121: Use Https To Access The Router
This is expected behavior. You can proceed, or add an exception for the security warning. For more information, visit kb.netgear.com/000062980/what-to-do-incase-of-security-message. To require HTTPS connections: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 122: Manage The Router Configuration File
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To change the router’s device name: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3.
Page 123: Restore The Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 4. Select ADVANCED > Administration > Backup Settings. The Backup Settings page displays. 5. Click the Back Up button. 6. Follow the direction of your browser to save the .cfg file. A copy of the current settings is saved in the location that you specify.
Page 124: Monitor The Router And Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To erase the settings: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3. Enter the router admin user name and password. The user name is admin.
Page 125: View Devices Currently On The Network
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays. 4.
Page 126: View And Manage Logs Of Router Activity
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • IP Address: The IP address that the router assigned to this device when it joined the network. This address can change if a device is disconnected and rejoins the network. •...
Page 127: View The Internet Connection Status Or Renew The Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To view and manage logs: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays. 3. Enter the router admin user name and password. The user name is admin.
Page 128 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The information in this section applies to Internet connections that do not require you to log in to your ISP, L2TP connections, and PPTP connections. To view the Internet connection status or renew the connection: 1.
Page 129: View The Pppoe Internet Connection Status Or Renew The Connection
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 View the PPPoE Internet connection status or renew the connection If your router is set up to use a PPPoE Internet connection, you can view the PPPoE connection status and, if necessary, manually restart the connection. To view the PPPoE Internet connection status or renew the connection: 1.
Page 130: Monitor, Meter, And Control Internet Traffic
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays. 4.
Page 131: Start The Traffic Meter Without Traffic Volume Restrictions
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Start the traffic meter without traffic volume restrictions You can monitor the traffic volume without setting a limit. To start or restart the traffic meter without configuring traffic volume restrictions: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 132 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 3. Enter the router admin user name and password. The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays.
Page 133: Restrict Internet Traffic By Connection Time
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Restrict Internet traffic by connection time If you connect to the Internet with a session-based connection type, you can record and restrict traffic by connection time. This is useful when your ISP measures your connection time.
Page 134: View The Internet Traffic Volume And Statistics
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 View the Internet traffic volume and statistics If you enabled the traffic meter (see Start the traffic meter without traffic volume restrictions on page 131), you can view the Internet traffic volume and statistics. To view the Internet traffic volume and statistics shown by the traffic meter: 1.
Page 135: Set The Ntp Server
Your settings are saved. Set the NTP server By default, the router uses the NETGEAR Network Time Protocol (NTP) server to sync the network time. You can change the NTP server to your preferred NTP server. To set the NTP server: 1.
Page 136: Set Your Time Zone And Daylight Saving Time
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Use the default NETGEAR NTP server: Use the preset NETGEAR NTP server. • Set your preferred NTP server: Enter the name or IP address of your preferred server. 6. If you select the Set your preferred NTP server radio button, enter the NTP server domain name or IP address in the field below the radio button.
Page 137: Set Up The Router As A Wifi Access Point
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set up the router as a WiFi access point You can set up the router to run as an access point (AP) on the same local network as another router. When you set up the router as an AP, some of its router features are disabled so that they do not interfere with the router features of the other router.
Page 138: Return The Router To Router Mode
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Return the router to router mode By default, your router is set to router mode. If you changed the mode to access point mode (AP mode), you can change the mode back to router mode. To return the router to router mode: 1.
Page 139: Connect To Your Router With Anywhere Access
Nighthawk app for your mobile device. For more information about how to update your router’s firmware, see Update the router firmware on page 116. To download the latest Nighthawk app for your mobile device, visit netgear.com/home/apps-services/nighthawk-app. Manage and Monitor Your User Manual Router...
Page 140: Return The Router To Its Factory Default Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Return the router to its factory default settings Under some circumstances (for example, if you lost track of the changes that you made to the router settings or you move the router to a different network), you might want to erase the current configuration and reset the router to factory default settings.
Page 141: Erase The Settings
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Erase the settings CAUTION: This process erases all settings that you configured in the router. To erase the settings: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 142: Chapter 10 Share A Usb Storage Device Attached To The Router
• Change a network folder on a USB storage device • Add a network folder on a USB storage device • Safely remove a USB storage device • Change the media server settings or rescan media files For more information about ReadySHARE features, visit netgear.com/readyshare.
Page 143: Usb Device Requirements
The router works with most USB-compliant external flash and hard drives. For the most up-to-date list of USB devices that the router supports, visit kb.netgear.com/app/answers/detail/a_id/18985/~/readyshare-usb-drives-compatibility-list. Some USB external hard drives and flash drives require you to load the drivers onto the computer before the computer can access the USB storage device.
Page 144: Display Network Folders On A Storage Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Display network folders on a storage device You can display network folders on a storage device that is connected to the router. To display network folders: 1. Launch a web browser from a computer or mobile device that is connected to the router network.
Page 145: Access A Storage Device Connected To The Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Access a storage device connected to the router From a computer or mobile device on your network, you can access a USB storage device that is connected to the router. Access a storage device connected to the router from a Windows-based computer To access the USB storage device from a Windows-based computer: 1.
Page 146 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 When you connect the USB storage device to the router’s port, it might take up to two minutes before it is ready for sharing. By default, the USB storage device is available to all computers on your local area network (LAN).
Page 147: Manage Access To A Usb Storage Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 5. When prompted, select the Guest radio button. 6. Click the Connect button. A window automatically opens and displays the files and folders on the USB storage device. Manage access to a USB storage device You can manage how you access a USB storage device that is connected to the router: •...
Page 148 Use Dynamic DNS to Access a USB Storage Device From the Internet on page 154. If you set up DDNS, you can also type a URL domain name. For example, if your domain name is MyName and you use the NETGEAR DDNS service, you can type https://MyName.mynetgear.com or ftp://MyName.mynetgear.com to access the USB device over the Internet.
Page 149 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To remove the password requirement, clear the associated Admin Password Protection check box. 8. Click the Apply button. Your settings are saved. Enable FTP access within your network File Transfer Protocol (FTP) lets you download (receive) and upload (send) large files faster.
Page 150: Change A Network Folder On A Usb Storage Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Change a network folder on a USB storage device By default, when you connect a USB storage device to a router USB port, the entire device is shared. You can change the network folder to limit access to specific files or folders.
Page 151: Add A Network Folder On A Usb Storage Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Add a network folder on a USB storage device You can add network folders on a USB storage device that is connected to a router USB port. To add a network folder on a USB storage device: 1.
Page 152: Safely Remove A Usb Storage Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 11. Click the Apply button. The folder is added on the USB storage device. 12. Click the Close Window button. The window closes. Safely remove a USB storage device Before you physically disconnect a USB storage device from the router USB port, log in to the router and take the USB storage device offline.
Page 153 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To change the media server settings or rescan media files: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays.
Page 154 Use Dynamic DNS to Access a USB Storage Device From the Internet With Dynamic DNS (DDNS), you can use the Internet to access a USB device that’s connected to a USB port on the router when you’re not home. This chapter contains the following sections: •...
Page 155: Set Up And Manage Dynamic Dns
Internet. Set up a new Dynamic DNS account If you do not yet have a Dynamic DNS (DDNS) account, NETGEAR provides you the opportunity to set up a free account.
Page 156 Use a Dynamic DNS account that you already have If you already have a Dynamic DNS (DDNS) account with NETGEAR, No-IP, or DynDNS, you can set up the router to use your existing account. To set up DDNS if you already have an account: 1.
Page 157 Manage your existing NETGEAR or No-IP Dynamic DNS account You can manage the settings for your existing NETGEAR or No-IP Dynamic DNS (DDNS) account, or reset your password for the DDNS account. To manage your DynDNS account, visit the DynDNS website.
Page 158 With your customized free URL, you can use FTP to access your network through Dynamic DNS when you aren’t home. To set up your FTP server, you must register for a NETGEAR Dynamic DNS (DDNS) service account and specify the account settings. See Set up a new Dynamic DNS account on page 155.
Page 159 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 4. Select ADVANCED > USB Functions > Advanced Settings. The USB Storage (Advanced Settings) page displays. 5. Select the FTP (via Internet) check box. The default port is number 21. Password protection is enabled by default. We highly recommend that you keep password protection enabled.
Page 160 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays. 4.
Page 161 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To access a device from a remote computer: 1. Launch a web browser on a computer that is not on your home network. 2. Connect to your home router: The link that lets you access the device over the Internet is https://public-ip-address/shares.
Page 162 Use OpenVPN to Access Your Network You can use OpenVPN software to remotely access your router with virtual private networking (VPN). This chapter explains how to install and use OpenVPN software to set up a VPN tunnel. The chapter contains the following sections: •...
Page 163 • To use a DDNS service, register for a DDNS account with a host name. You use the host name to access your network. The router supports these DDNS accounts: NETGEAR, No-IP, and Dyn. For more information, see Set up and manage Dynamic DNS on page 155.
Page 164 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 If both networks use the same LAN IP scheme, when the VPN tunnel is established, you cannot access your home router or your home network with the OpenVPN software. For information about changing the LAN settings on the router, see Change the LAN IP address settings or RIP settings on page 94.
Page 165 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The default protocol for TUN mode is UDP. • To change the TUN mode service port, type the port number that you want to use in the field. The default port number for TUN mode is 12973. The TUN port number is used in the .ovpn file of the OpenVPN configuration software package for Mac and non-Windows clients.
Page 166: Install Openvpn Software On A Windows-Based Computer
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NOTE: If you later change the OpenVPN configuration for the router (for example, you change the TUN or TAP port number), you must download and install the .ovpn configuration file again on each client, depending on its operating system.
Page 167 You can also import the unzipped .ovpn configuration file from the OpenVPN client user interface. 11. Modify the VPN interface name to NETGEAR-VPN: a. If your computer is running Windows 10 or newer, select Start > Settings > Network & Internet > Change adapter options.
Page 168: Install Openvpn Software On An Ios Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The BASIC Home page displays. 6. Select ADVANCED > Advanced Setup > VPN Service. The VPN Service page displays. 7. Make sure that the Enable VPN Service check box is selected. For more information about the VPN configuration for the router, see Enable OpenVPN service on the router on page 164.
Page 169: Install Openvpn Software On An Android Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 7. Click the For Smart Phone button to download the router’s OpenVPN configuration file to your computer or iOS device. If you download the configuration file to your computer, unzip the .ovpn file, and send it to your iOS device.
Page 170: Use Vpn To Access Your Internet Service At Home
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 For more information about the VPN configuration for the router, see Enable OpenVPN service on the router on page 164. 7. Click the For Smart Phone button to download the router’s OpenVPN configuration file to your computer or Android device.
Page 171: Block Vpn Client Internet Access In The Router
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To allow VPN clients to use your home Internet service: 1. Launch a web browser from a computer or mobile device that is connected to the router network. 2. Enter http://www.routerlogin.net. A login window displays.
Page 172 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 4. Select ADVANCED > Advanced Setup > VPN Service. The VPN Service page displays. 5. Make sure that the Enable VPN Service check box is selected. For more information about the VPN configuration for the router, see Enable OpenVPN service on the router on page 164.
Page 173: Manage Port Forwarding And Port Triggering
Manage Port Forwarding and Port Triggering You can use port forwarding and port triggering to set up rules for Internet traffic for services and applications. You need networking knowledge to set up these features. This chapter includes the following sections: •...
Page 174 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Manage port forwarding to a local server If a server is part of your network, you can allow certain types of incoming traffic to reach the server. For example, you might want to make a local web server, FTP server, or game server visible and available to the Internet.
Page 175: Add A Custom Port Forwarding Service Or Application
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 If the service or application that you want to add is not in the list, create a port forwarding rule with a custom service or application (see Add a custom port forwarding service or application on page 175).
Page 176: Change A Port Forwarding Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 You can specify ports and port ranges divided by commas, for example: 30, 50–60, 65500–65510. 11. Specify the internal ports by one of these methods: • Leave the Use the same port range for Internal port check box selected. •...
Page 177: Remove A Port Forwarding Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 For information about the settings, see Add a custom port forwarding service or application on page 175. 9. Click the Apply button. Your settings are saved. The changed rule displays in the table on the Port Forwarding / Port Triggering page.
Page 178: How The Router Implements The Port Forwarding Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 In this example, your router always gives your web server an IP address of 192.168.1.33. 2. On the Port Forwarding / Port Triggering page, configure the router to forward the HTTP service to the local address of your web server at 192.168.1.33. HTTP (port 80) is the standard protocol for web servers.
Page 179: Add A Port Triggering Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • An application must use port forwarding to more than one local computer (but not simultaneously). • An application must open incoming ports that are different from the outgoing port. With port triggering, the router monitors traffic to the Internet from an outbound “trigger” port that you specify.
Page 180: Change A Port Triggering Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 7. Specify the following settings: • Service Name: Enter the name of the custom service or application. • Service User: From the Service User menu, select Any, or select Single address and enter the IP address of one computer: ○...
Page 181: Remove A Port Triggering Rule
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The Port Forwarding / Port Triggering page displays. 5. Select the Port Triggering radio button. The port triggering settings display. 6. In the Port Triggering Portmap Table, select the radio button for the rule. 7.
Page 182 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Set the time-out period for port triggering The time-out period for port triggering controls how long the inbound ports stay open when the router detects no activity. A time-out period is required because the router cannot detect when the service or application terminates.
Page 183: Disable Port Triggering
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive. The BASIC Home page displays. 4.
Page 184: Application Example: Port Triggering For Internet Relay Chat
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Application example: Port triggering for Internet Relay Chat Some application servers, such as FTP and IRC servers, send replies to multiple port numbers. Using port triggering, you can tell the router to open more incoming ports when a particular outgoing port starts a session.
Page 185: Troubleshooting
Troubleshooting This chapter provides information to help you diagnose and solve problems you might experience with your router. If you do not find the solution here, check the NETGEAR support site at netgear.com/support for product and contact information. The chapter contains the following sections: •...
Page 186: Quick Tips
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Quick tips This section describes tips for troubleshooting some common problems. Sequence to restart your network If you must restart your network, follow this sequence: 1. Turn off and unplug the modem. 2.
Page 187: Check The Network Settings
Reboot the router from its router web interface You or NETGEAR technical support can reboot the router from its router web interface, either locally or remotely, for example, when the router seems to be unstable or is not operating normally.
Page 188: Troubleshoot With The Leds
• Make sure that the power adapter is securely connected to your router and securely connected to a working power outlet. • Make sure that you are using the power adapter that NETGEAR supplied for this product. Power LED stays solid amber or blinking...
Page 189: You Cannot Log In To The Router
If the error persists, it is likely that a hardware problem exists. For recovery instructions, or help with a hardware problem, contact Technical Support at netgear.com/support. Internet or Ethernet LAN port LEDs are off If the Internet LED or Ethernet LAN port LEDs do not light when an Ethernet connection is made, check the following: •...
Page 190 • If you are attempting to set up your NETGEAR router as a replacement for an ADSL gateway in your network, the router cannot perform many gateway services. For example, the router cannot convert ADSL or cable data into Ethernet networking information.
Page 191: You Cannot Access The Internet
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 NOTE: If you use high-speed fiber Internet service, you might not need a separate modem. Contact your Internet service provider (ISP) for more information. You cannot access the Internet If you can access your router but not the Internet, check to see if the router can obtain a Internet IP address from your Internet service provider (ISP).
Page 192 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Your Internet service provider (ISP) might be experiencing an outage. Try connecting a computer directly to your modem's Ethernet port and accessing the internet. If your computer still can't access the Internet, contact your ISP to troubleshoot your connection.
Page 193: Troubleshoot Internet Browsing
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 Troubleshoot Internet browsing If your router can obtain an IP address but your computer is unable to load any web pages from the Internet, it might be for the following reasons: •...
Page 194: Troubleshoot Your Network Using The Ping Utility
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 • Does the WiFi device that you are using find your WiFi network? If not, check the WiFi LED on the router. If it is off, log in to the router web interface and check if the WiFi radio is enabled or disabled.
Page 195: Test The Path From A Windows-Based Computer To A Remote Device
Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 To ping the router from a Windows-based computer: 1. From the Windows toolbar, click the Start button and select Run. 2. In the field provided, type ping followed by the IP address of the router, as in this example: ping www.routerlogin.net 3.
Page 196 Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1 If the path is functioning correctly, messages display that are similar to those shown in Test the LAN path to your router on page 194. 3. If you do not receive replies, check the following: •...

This manual is also suitable for:

Nighthawk rs150v1

NETGEAR Nighthawk RS200 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for NETGEAR Nighthawk RS200

Summary of Contents for NETGEAR Nighthawk RS200

This manual is also suitable for: