Related Manuals for Kellfri 35-WKM145
Summary of Contents for Kellfri 35-WKM145
- Page 1 35-WKM145 35-WKM175 FLAIL-MOWER Carefully read the operating instructions before using the product! Operating instructions translated from Swedish...
- Page 2 Deviation form Warranty terms and conditions Kellfri designs and supplies efficient, affordable machinery and components for forestry, agriculture, construction and gardening in Sweden, the rest of the Nordic region and Europe. We recommend that you always read and follow the safety instructions and the instructions in the machine's operating manual.
-
Page 3: Product Information
INTRODUCTION Thank you for choosing a product from Kellfri AB. Compliance with the general safety instructions, operating instructions and common sense will guarantee many years of enjoyment using the product. Kellfri's equipment and products are aimed at self-employed farmers who have stringent performance demands. -
Page 4: Safety Instructions
Kellfri AB, Storsvängen 2, SE-532 38 SKARA, Sweden. Tel.: +46 511 242 50 The safety instructions can also be downloaded from Kellfri's website: www.kellfri.co.uk Do not use the equipment or product if you feel ill, tired or are under the influence of alcohol. -
Page 5: Before Use
SURROUNDINGS Check that the work area is free from bystanders and objects before hitching or using the equipment. Otherwise, there is a risk of serious injury. Be extra careful if there are children in the vicinity of the area where the equipment or product is used or stored. Check that there are no low-hanging electrical cables within the work area. -
Page 6: After Use
Only those who understand the safety instructions and the operating manual may use the equipment or product. Exercise caution and care when working with the equipment or product and only use it in the way described in the instruction manual. There is a risk of crushing when working with equipment that has moving parts. -
Page 7: Maintenance And Service
Do not use your hands to locate leaks. Use a piece of paper or cardboard to search for leaks. Kellfri AB has a policy of continuous product development and therefore reserves the right to make modifications, e.g. to the design and appearance of the product, without prior notice. - Page 8 FOR USING MACHINE/EQUIPMENT CONNECTED TO TRACTOR PAY ATTENTION TO THE FOLLOWING: • Carefully read the machine's operating manual before using the machine! It is important that you understand the directions in the manual. • Keep the work area clear of children and other people. Moving parts increase the risk of accidents.
-
Page 9: Power Take-Off Shaft
MACHINERY/EQUIPMENT CONNECTED TO HYDRAULICS Be careful when you connect your machine or equipment to a hydraulic hose. DANGER! Pressurised oil and fuel leaks can penetrate skin and cause serious injuries. Do not use your hands to locate leaks. Use a piece of paper or cardboard to search for leaks. •... - Page 10 RISKS AND HAZARDS ASSOCIATED WITH THE USE OF GRASSLAND MACHINERY Risk of crushing Observers can be injured when the machine is lowered in the cutting position. Pasture toppers have crushing points around the hinge areas and between the 3-point linkage and the main body.
- Page 11 All unprotected rotating machine parts increase the risk of accidents. Accidents usually occur when loose-fitting clothing or long hair is caught and wrapped around rotating parts, such as PTO shafts or drive shafts on the machine. Ensure that all guards are correctly fitted. DRIVE SAFELY ON PUBLIC ROADS •...
-
Page 12: Warning Decals
WARNING DECALS Make sure warning decals are always visible and clean them when necessary. Do not use a high-pressure washer directly on the warning decal. If a part with a decal is replaced, or the decal becomes worn or in any other way unusable, order a new set of decals. SYMBOL EXPLANATION Read the operating manual! Before carrying out work. - Page 13 CHEMICALS To maximise the service life of a product/equipment, maintenance - and not least preven- tive maintenance - is important, and this is largely what greases and oils do. Carefully read the operating manuals for your new products or equipment to ensure correct maintenance and service life and that the warranty remains valid! Lubricating greases First aid measures.
- Page 14 PARTS Tools Spanner: 18 and 19 mm Swivel joint wrench: 10 and 16 mm M10x25 2 pcs M6x25 3 pcs M12x40 8 pcs Table of Contents...
- Page 15 ASSEMBLY M12x40 NOTE: Left and right See position of holes during assembly. M12x40 Table of Contents...
- Page 16 M12x40 Table of Contents...
- Page 17 M10x25 The hook acts as a support for the PTO shaft. Table of Contents...
-
Page 18: Troubleshooting
Storage for documents, small tools etc. M6x25 SERVICE INTERVAL MEASURE Before each use Replace all defective flails. Sharp blades give better results. When replacing blades, tighten bolts fully. Flails While operating Listen out for noises After each use Check Gearbox Before each use Check level Transmission oil... -
Page 19: Before Operation
BEFORE OPERATION • Important! Check re-tightening of all bolts and nuts, especially bolts for clamp bushings and belt pulleys! IMPORTANT! Check mounting bolts for CLAMP BUSHINGS and BELT PULLEYS. Re-tighten the pulley bolts at regular intervals. • Check that blades or flails are in their correct position. REPLACE broken, cracked or worn-out blades or flails. - Page 20 REFILLING THE PIPE ALWAYS CHECK THE LEVEL BEFORE OPERATION! REFILLING WITH TRANSMISSION OIL 80W-90 LEVEL PLUG WKM145 0.25L WKM175: 0.25L GEARBOX WKM145/WKM175 OIL REFILLING TRANSMISSION OIL 80W-90 (1.2 L) LEVEL PLUG Screw off the guard to reach the level plug DRAINAGE PLUG Table of Contents...
-
Page 21: Checking Belt Tension
CHECKING BELT TENSION BELT GUARD Belt 17X1016Li ILLUSTRATION 1 CHECK AND TIGHTEN COG BELT AFTER ONE HOUR OF OPERATION!! CHECK BELT TENSION REGULARLY The belt should move 20 mm under pressure. (10 mm on each side - see illustration 2) ILLUSTRATION 2 Re-tighten the pulley bolts at regular intervals. -
Page 22: Belt Adjustment
BELT ADJUSTMENT MOUNTING BOLTS ADJUSTMENT BOLT Loosen the mounting bolts for the gearbox and pulley. (See illustration.) Then adjust the adjustment bolt until the belts are adequately tightened. CHECK AND TIGHTEN THE BELTS AT REGULAR INTERVALS. NEW MACHINE - CHECK AND TIGHTEN THE BELTS AFTER TWO HOURS OF OPERATION. Table of Contents... -
Page 23: Grease Points
GREASE POINTS Lubricate the indicated grease nipples regularly, and every time you rinse off the machine, to remove the water that has penetrated into the bearings during the rinsing. Inadequate lubrication can result in unnecessary wear and mechanical damage. Use a universal lubricant. IMPORTANT! Avoid over-lubricating. - Page 24 Version 1.1 Table of Contents...
- Page 25 ITEM NO. SPARE PART NO. DESIGNATION QUANTITY QUANTITY R35-WKM145.007 Chassis R35-VKM175.022 Skid shoe, right R35-VKM175.023 Skid shoe, left R35-VKM145.003 Blade cylinder/rotary shaft R35-VKM175.039 R35-VKM175.018 Adjustment plate for support roller, left R35-VKM175.019 Adjustment plate for support roller, right VKMATV150HXL.003 Bearing UC207 + bearing housing R60-SEAL.035 Radial seal 55 x 80 x 8 R35-VKM195H.028...
- Page 26 Version 1.1 Table of Contents...
- Page 27 ITEM NO. SPARE PART NO. DESIGNATION QUANTITY QUANTITY R35-VKM195H2.058 Locking nut M14 R35-VKM195H2.057 Hex key M14 x 35 Flat washer 12 x 2.5 R35-RS165H.017 Locking nut M12 R35-VKM195H2.066 Hex key M12 x 35 R35-VKM195H2.037 Hex key M12 x 40, full thread Spring washer 12 Hex key M12 x 30 Hex key M8 x 20...
- Page 28 Version 1.1 ITEM SPARE PART NO. DESIGNATION QUANTITY QUANTITY R35-VKM175.046 Drive cup 33mm - 33mm R35-VKM175.044.2 Drive shaft VKM175 L:424mm R35-VKM175.042 Shaft pipe Hex key 8 x 12 Hex key M12 x 35 Flat washer 12 x 2.5 Spring washer 12 R60-SGH62 Circlip SGH62 R60-SGH35...
- Page 29 Version 1.1 ITEM SPARE PART NO. DESIGNATION QUANTITY QUANTITY R35-VKM145.003 Blade cylinder/rotary R35-VKM175.039 shaft R35-SK180.002 Hammer flails Hex key M16 x 80 R35-SK140.008 Locking nut M16 Table of Contents...
- Page 30 FLAILS The product is supplied with hammer flails. The possibility of replacing them with Y-flails is available as an option. Hammer flail article no.: R35-SK180.002, R35-SK180.002.2 Y-flails - article no.: R35-SK180.003 Spacer - article no.: R35-VKM175.008 Table of Contents...
- Page 31 DEVIATION FORM We are grateful for your help in pointing out any defects in the product supplied to you by Kellfri. Before making a claim, read Kellfri's general purchase terms and conditions in our catalogue or on our website www.kellfri.co.uk, and in the operating manual if supplied.
-
Page 32: Warranty Terms And Conditions
You are always welcome to give feedback or ask us about our equipment and products. Kellfri AB has a policy of continuous product development and therefore reserves the right to make modifications, e.g. to the design and appearance of the product, without prior notice.
Need help?
Do you have a question about the 35-WKM145 and is the answer not in the manual?
Questions and answers