Page 1
35-RKATV117 ATV ROUGH MOWER CAREFULLY READ THE OPERATING INSTRUCTIONS BEFORE USING THE PRODUCT! OPERATING INSTRUCTIONS TRANSLATED FROM THE ORIGINAL...
TABLE OF CONTENT Product information Technical data For your safety Product safety information In case of emergencies Personal protection Surroundings Warning signs and labels Before use Use/operating Connecting Cut height - adjusting Driving and speed After use Petrol handling Transport and storage Maintenance and service 10-12 Maintenance of knives...
Thank you for choosing a product from Kellfri AB. By following the general safety information and the in- struction manual and by using common sense, you will have a great and safety use of your Kellfri product for many years. Kellfri designs and delivers effective, affordable machinery and components for forest, agriculture, construction and gardening in Sweden, other Nordic countries and Europe.
If the instructions manual is damaged or otherwise unusable If the instructions manual is dam- aged or otherwise unusable, please contact your retailer. For more information visit our website: https://www.kellfri.co.uk/ Do not use this equipment if you are feeling sick, tired or in influence of alcohol. Nor if you are under the influence of strong medications or drugs, suffering from strong depression or severe mental illness.
PERSONAL PROTECTION Always wear suitable clothing and footwear. Do not wear loose clothing or jewelry when using the machine. Remember to put up long hair when operating rotating machines. Wear protec- tive gloves, to prevent risking burns on contact with hot surfaces such as exhaust system, and to avoid oil and gasoline on the skin.
WARNING DECALS Ensure that warning labels are always visible and clean. Clean the warning labels as required. Do not rinse using pressure washer directly on the warning labels. Any damage/ brokenstick- ers should be replace. Order new stickers from your supplier. SYMBOL EXPLANATION LOCATION...
Learn and remember the correct working methods. Beginners should always keep a low speed, use extreme caution before routine and product knowledge is achieved. The user/cus- tomer is responsible to handle the situation correctly. The product should not be taken into use unless it can be done in a safe way for the user.
CUTTING HEIGHT The mower must be turned off when adjusting the cutting height. Never adjust the cutting height with the engine running. The cutting height is adjusted by turning the lever. Turn the lever clockwise to lower the knife down and counterclockwise to raise Make sure that the mower is always kept horizontal by adjusting the handle.
The amount of grass to be cut determines the forward speed; low speed usually gives the best result. Make sure that you follow these procedures. Normal speed 1 km / h at heavy work, 8 km / h at very light work. Do not exceed the maximum driving speed 8km / h when driving Start with the lowest possible speed, ensure that the mower is working effectively with the engine at maximum speed without effort.
Perform maintenance, servicing and inspections as recommended. Use only parts with equivalent performance to reduce the risk of damage and failure. For spare parts: contact Kellfri Service Check all bolts and nuts are tightened after maintenance and service. Always test the machine before work is started.
Page 11
LUBRICATING Lubricate the draw coupling Check the coupling to see signs of damage or wear. Replace damaged and / or worn parts. Lubricate the coupling regularly. LUBRICATE ALL LUBRICATION POINTS Open the cover and lubricate the bearings for the strap. EVERY 8TH HOUR OF OPERATING: WARNING: ENGINE MUST BE TURNED OFF BEFORE LUBRICATION IS IMPLEMENTED Lubricate the bearings carefully, unnecessary wear and mechanical damage may result from...
Page 12
Open the plate protection, to get to the grease fitting under the engine. Lubricate bearings CHANGING OIL Use the correct type of oil depending on temperature conditions. Use SAE 5W-30 or SAE-30. See table:...
MAINTENANCE OF KNIVES The mower is equipped with blades made to last for a long time. If a knife loosens or breaks down, it is important to replace it immediately. If not, there is a possible imbalance, which is very serious. If it is partly or completely worn out, it should be replaced to maintain the correct weight balance.
LONG TIME STORAGE: Before the storage, be sure to follow the below • Drain the engine on or add a stabilizer in the fuel to prevent fuel becomes messy. • If you have added stabilizer, run the engine for about 5 minutes .. •...
DESCRIPTION ENGINE: 16 hp Petrol tank, volume 13 L Petrol level gauge Ball coupling: 50 mm Drawbar bracket: for use in sideway direction Wheel: Maximum wheel pressure 2,06 Bar /30 PSi SPARE PARTS ART.NO. NAME R35-RKATV.001 Knife R35-RKATV.004 Bearings for knives R35-RKATV.005 Wheel R35-RKATV.015...
ASSEMBLY INSTRUCTIONS STEP 1: Installation of the gas tank and the support frame Assembly the support frame (3 parts #49, #51, #47), lock in place with 2 M8x35 (#53) and lock nut M8 (#4) Mount the tank on the frame, lock in place with M8x25 (#2), spring disc Ø8 (#3) and large disc Ø8 (#52) Mount the stabilizer bar (#50) for stabilizing the frame (A-A), lock in place with 2 M8x35 (#53) and lock nut M8 (#4)
Page 17
Step3: Installing the tank on the mower 1. Place the frame with the tank above the mower (#20) and lock in place with 6 bolts M8x25 (#2), spring disc Ø8 (#3) and lock nut M8 (#4) SAE 5W-30 /SAE 5-30 Step 4: Fill the engine with oil 1.
Page 19
NAME AMOUNT NAME AMOUNT Petrol tank Spring Six point bolt M8x25 Side disc Lock disc Ø8 Six point bolt M5x12 Lock boltM8 Lock disc Ø5 Hooks for battery Washers Rubber bushing Six point bolt Engine Adjustable disc B V-belt SPB686 Plate - back V-belt SPB2182 Adjustable disc A...
Page 21
Pos no. NAME AMOUNT Lock disc Ø8 Lock nut M8 Lock disc Ø10 Lock nut M10 Lock nut M12 Six point bolt M8x30 Six point bolt M10x45 Washers Ø8 Bushing Adjustable handle Six point boltM12x55 Main frame Cotter pin Ø4x40 Track nutM16x1.5 WashersØ16 Wheel...
Page 22
Pos no. NAME AMOUNT Pos no. NAME AMOUNT Lock disc Ø8 Bushing for engine Lock disc Ø5 Socket head bolt M8x25 Washers Pulley C Disc Wedge for pulley C Muffler Engine16hp Six point bolt 5/16”x1” 12V Battery Flanged pin M6x120 Wire Flanged pin 7/16x40 Six point bolt M5x16...
Page 23
Pos no. NAME AMOUNT Six point bolt- M12x60 Lock nut M12 Lock disc Ø12 Draw coupling Draw pipe Washers Ø12 Pos no. NAME AMOUNT Pop rivets Ø5x12 Clamp Protective cover Pop rivets Ø16x12 Strap cover Rubber strip - long Rubber strip - short Hinge...
COMPLAINT FORM We are grateful for your help pointing out any inaccuracies in the Kellfri product delivered to you. Before making a complaint read Kellfris general warranty and sales conditions in our catalog as well as the enclosed User’s manual that comes with the machine.
Other equipment must meet the hardware requirements of the Directive. Tina Baudtler, VD Kellfri AB is constantly working on further developing their products and therefore re- servesthe right to modify, among other things the design and appearance without no- tice.