Related Manuals for Kellfri 35-WKM125
Summary of Contents for Kellfri 35-WKM125
- Page 1 35-WKM125 FLAIL MOWER Carefully read the operating instructions before using the product! Operating instructions translated from Swedish...
-
Page 2: Table Of Contents
Deviation form Warranty terms and conditions Kellfri designs and supplies efficient, affordable machinery and components for forestry, agriculture, construction and gardening in Sweden, the rest of the Nordic region and Europe. We recommend that you always read and follow the safety instructions and the instructions in the product's operating manual. -
Page 3: Introduction
INTRODUCTION Thank you for choosing a product from Kellfri AB. Compliance with the safety instructions, operating manual and sound common sense will guarantee many years of enjoyment using the product. Kellfri's equipment and products are aimed at self-employed farmers, horse enthusiasts and other country-dwellers who have stringent performance demands. -
Page 4: Safety Instructions
If the safety instructions or the operating manual are damaged, or become unusable for any other reason, new copies may be ordered from: Kellfri AB, Munkatorpsgatan 6, SE-532 37 SKARA, Sweden. Tel.: +46 511 242 50 The safety instructions can also be downloaded from Kellfri's website: www.kellfri.co.uk... -
Page 5: Surroundings
SURROUNDINGS Check that the work area is free from bystanders and objects before hitching or using the equipment. Otherwise, there is a risk of serious injury. Be extra careful if there are children in the vicinity of the area where the equipment or product is used or stored. Check that there are no low-hanging electrical cables within the work area. -
Page 6: Use
Only those who understand the safety instructions and the operating manual may use the equipment or product. Exercise caution and care when working with the equipment or product and only use it in the way described in the instruction manual. There is a risk of crushing when working with equipment that has moving parts. -
Page 7: Maintenance And Service
Do not use your hands to locate leaks. Use a piece of paper or cardboard to search for leaks. Kellfri AB has a policy of continuous product development and therefore reserves the right to make modifications, e.g. to the design and appearance of the product, without prior notice. -
Page 8: For Using Machine/Equipment Connected To Tractor
FOR USING MACHINE/EQUIPMENT CONNECTED TO TRACTOR PAY ATTENTION TO THE FOLLOWING: • Carefully read the machine's operating manual before using the machine! It is important that you understand the directions in the manual. • Keep the work area clear of children and other people. Moving parts increase the risk of accidents. •... -
Page 9: Machinery/Equipment Connected To Hydraulics
MACHINERY/EQUIPMENT CONNECTED TO HYDRAULICS Be careful when you connect your machine or equipment to a hydraulic hose. DANGER! Pressurised oil and fuel leaks can penetrate skin and cause serious injuries. Do not use your hands to locate leaks. Use a piece of paper or cardboard to search for leaks. •... -
Page 10: Risks And Hazards Associated With The Use Of Grassland Machinery
RISKS AND HAZARDS ASSOCIATED WITH THE USE OF GRASSLAND MACHINERY Risk of crushing Observers can be injured when the machine is lowered in the cutting position. Pasture toppers have crushing points around the hinge areas and between the 3-point linkage and the main body. Respect the risk zone of 15 m! Rotating blades WARNING! Any person can risk injury by putting their hands or feet under the machine when it is... -
Page 11: Drive Safely On Public Roads
All unprotected rotating machine parts increase the risk of accidents. Accidents usually occur when loose-fitting clothing or long hair is caught and wrapped around rotating parts, such as PTO shafts or drive shafts on the machine. Ensure that all guards are correctly fitted. DRIVE SAFELY ON PUBLIC ROADS •... -
Page 12: Warning Decals
WARNING DECALS Make sure warning decals are always visible and clean them when necessary. Do not use a high- pressure washer directly on the warning decal. If a part with a decal is replaced, or the decal becomes worn or in any other way unusable, order a new set of decals. SYMBOL EXPLANATION Read the operating manual! Before carrying out work. -
Page 13: Chemicals
To ensure the best lubricating effect, you need to clean parts of the product or equipment from time to time. We recommend degreasing to achieve thorough cleaning and to remove all residues of old lubricant, which may contain destructive particles. The degreasing agent we supply at Kellfri is OKQ8, in a 20-litre can. Table of Contents >>... -
Page 14: Before Using The Machine
BEFORE USING THE MACHINE * IMPORTANT! Check and tighten all bolts, nuts and all connections and specially the clamp sleeve for the pulley Check clamp sleeve for the pulley. The bolts should be tightened at regular intervals. Tighten and check the belt tension if neces- sary. -
Page 15: Transport And Storage
Operate at 540 rpm, start at the lowest possible speed, make sure the mower works efficiently with the engine on 540 rpm without effort. Stop and check that the cutting unit is set correctly after the first 10 meters. Before maintenance, service, connection and disconnection of the machine, the tractor engine must switched off and the ignition key removed. -
Page 16: Parts 35-Wkm125
PARTS 35-WKM125 Tools needed: 16 / 17 / 18 och 19 mm wrench NOTE! During assembly, tighten all bolts first by hand. Finish tightening all bolts with the wrench when the product is fully assembled. Important double check all bolts are tightened... - Page 17 STEP 2 M12x35 STEP 3 M10x25 STEP 4 M10x15 Table of Contents >>...
-
Page 18: Fill The Tube With Oil
FILL THE TUBE WITH OIL ALWAYS check the level before operation. level plug The level plug is located on the back of the tube. Top-up - transmission oil 80W-90, about 0.2 liters GEARBOX Top-up - transmission oil 80W-90, about 0,7 liter Level plug drain plug Table of Contents >>... -
Page 19: Checking Belt Tension
CHECKING BELT TENSION Belt guard Type of belt: BX17X1016 Behind the cover there is a greasing point BILD1 CHECK AND TIGHTEN THE V-BELT AFTER 1 HOUR DRIVE !! CHECK BELT TENSION REGULARLY The belt should move 20 mm (10 mm on each side) under pressure. -
Page 20: Belt Adjusment
BELT ADJUSMENT Fastening bolts Adjuster Release the fastening bolts for the gearbox and the pul- ley (see images). Then adjust the adjusting bolt until the belts are tight enough. CHECK AND TIGHTEN THE BELTS AT REGULAR INTERVALS. A NEW MACHINE SHOULD BE CHECKED AND THE BELTS TIGHTENED AFTER 2 HOURS OF OPERATION. - Page 21 Table of Contents >>...
-
Page 22: Maintenance And Service
MAINTENANCE AND SERVICE Make sure the implement is stable and there’s no risk of falling over during maintenance and ser- vice. Replace damaged and worn parts immediately to reduce the risk of machine failure and in- juries. Perform maintenance, service and inspections as recommended. Use only spare parts with equivalent performance to reduce the risk of damage and failure. -
Page 23: Flails
FLAILS WARNING! NEVER mount different types of flails on the mower. When the flails have been mounted, always check the tightness of the flail screws. Ensure that all screws are fully tightened. Mounting of hammer flail onto verge flail mower. Hammer flails can be replaced with Y-flails (not included, may be purchased additionally). - Page 24 Table of Contents >>...
-
Page 25: Parts List I
PARTS LIST I POS.NO PART NO. SPECIFICATION R35-VKM175.022 Skid, left R35-VKM175.023 Skid, right R35-WKM125.001 Rotor shaft R35-VKM175.018 Adjustment plate support roller, right R35-VKM175.019 Adjustment plate support roller, left VKMATV150HXL.003 Bearing UC207 + housing R60-TÄTNING.035 Radial seal 55x80x8 R35-VKM195H.028 Sleeve lower pulley R35-VKM175.043 Gearbox bracket R35-VKM175.005... - Page 26 Table of Contents >>...
-
Page 27: Parts List Ii
PARTS LIST II POS.NO PART NO. SPECIFICATION Split pin 4x25 R35-SK140.037 PTO cover plastic R35-VKM195H2.054 Hexagonal bolt M10x16 Spring washer 10x2.6 R-pin 4 R35-VKM195H2.048 Hexagonal plug 3/8 R35-VKM195H2.065 Hexagon screw M12x35 R60-SGH62 Circlip SGH62 Flat washer 8 VKMATV150HXL.087 Hexagon locking nut M8 R35-VKM175.010 V-belt BX40 Li1016 R35-WKM125.007... -
Page 28: Flail
FLAIL The product is delivered with hammer flails. As an option, you can exchange the hamer flails with Y-flails. Hammer flail - product no.: R35-VKM195H.001 Table of Contents >>... - Page 29 Y-flail - product no: R35-SK180.003 spacer - product no.: R35-VKM175.008 Table of Contents >>...
-
Page 30: Directions For Shortening The Pto Shaft
DIRECTIONS FOR SHORTENING THE PTO SHAFT 1. Remove the protective device. 2. Cut off the transmission shaft to the desired length. NB The shaft may not be cut more than half the tube length. 3. File the edges of the tube 4. -
Page 31: Deviation Form
DEVIATION FORM We are grateful for your help in pointing out any defects in the product supplied to you by Kellfri. Before making a claim, read Kellfri’s general purchase terms and conditions in our catalogue or on our website www.kellfri.co.uk, and in the operating manual if supplied. -
Page 32: Warranty Terms And Conditions
You are always welcome to give feedback or ask us about our equipment and products. Kellfri AB has a policy of continuous product development and therefore reserves the right to make modifications, e.g. to the design and appearance of the product, without prior notice.