Advertisement
Quick Links
Advertisement
Related Manuals for ComMarker Omni
Summary of Contents for ComMarker Omni
- Page 1 ComMarker Omni Users’ Manual...
-
Page 2: Table Of Contents
Table of contents Safety Warning ..............................3 Product Structure ............................... 4 List of Items ................................ 5 Assembly of Machine ............................6 Parameters ................................. 6 Turn On the laser ..............................6 Operation Instructions ............................8 Lightburn Operation Tutorial ........................... 13 ................................... 13... -
Page 3: Safety Warning
Safety Warning Before using the laser engraving machine, please read this safety guide carefully. Before using the laser engraving machine, please read this safety guide carefully. Before using the laser engraving machine, please read this safety guide carefully. ■ Do not leave the device unattended Do not leave the device unattended while in operation. -
Page 4: Product Structure
Product Structure... -
Page 5: List Of Items
List of items... -
Page 6: Assembly Of Machine
Assembly of Machine 1. Place the parts on the table. 2. Fasten the supporting pole with four screws. 4. Connect the external signal and power cables for 3. Fix the laser head on the shelf laser head 6. Connect the wire cable on the case 5. -
Page 7: Parameters
Parameters Voltage 110V/220V Laser Type: UV laser Working Area 70*70mm and 150*150mm Wavelength 355nm Marking Speed: 0- 7000mm/s Accuracy 0.01mm Graphic Format Supported: AI/PLT/JPG/DXF System Supported Window7/8/10/11 Cooling Type Air Cooling Output Power Dimension(L*W*H): 35x65x72cm Weight (KG): 23kg Turn on the laser Connect the Power cable and switch on the power, the laser's switch indicator light will alternately the laser's switch indicator light will alternately flash... -
Page 8: Operation Instructions
Operation Instructions 1. Install the driver Note：Please insert the USB drive into the computer lease insert the USB drive into the computer before operation. It is recommended to copy the recommended to copy the files from the USB drive to the desktop. files from the USB drive to the desktop. - Page 9 5.Find the corresponding file in the USB drive, click OK 5.Find the corresponding file in the USB drive, click OK 6.Click "Install" 7.Click “finish” if it is successful 8.it will display "BJJCZ Device" in Device Manager 8.it will display "BJJCZ Device" in Device Manager Noted: *It is recommended to copy and paste the files of the U disk to the computer desktop or other and paste the files of the U disk to the computer desktop or other and paste the files of the U disk to the computer desktop or other...
- Page 10 2. Open the software Open the USB folder omni 1; open the " open the "software15” folder. Open the software “EZCAD2 EZCAD2”. You can enter "text", "picture" or "vector diagram" as shown in the figure below. It is recommended to select the text to "text", "picture"...
- Page 11 4. Adjust the focus Press up or down button to lift or lower the laser head until the 2 red light point overlap, which is the best Press up or down button to lift or lower the laser head until the 2 red light point overlap, which is the best Press up or down button to lift or lower the laser head until the 2 red light point overlap, which is the best focal point.
- Page 12 5.Press “red light” to ensure it’ll mark on the test ll mark on the test 6. Meanwhile, lift or lower the laser head and observe lower the laser head and observe material. Click “mark”, and the laser would be , and the laser would be the obvious change of intensity of the laser beam.
-
Page 13: Lightburn Operation Tutorial
Lightburn icon to the Applications folder Lightburn icon to the Applications folder 3.Copy the folder “Omni 1” from the USB to the desktop from the USB to the desktop 4. A device window will pop out if the software is open 4. - Page 14 Device setting” button, 12. Change the setting of Freq 12. Change the setting of Freq “Min 1”, “Max 40”. click “Load COR file”, Select “omni 1 omni 1”, Choose file Switch on “Galvo 2”. Set the Laser Type UV, a Set the Laser Type UV, and it is “JCZ15.cor”, Click “OK”...
-
Page 15: Faq
USB flash drive is damaged and cannot be opened *Please visit Commarker's official website to download the ficial website to download the omni driver and software. *Contact after-sales staff or email us Q3: The red light preview functions, but there is no... - Page 16 Q7: The preview and the shape of the mark of the mark is deformed *Import the calibration file, please refer to step 3 of the operating instructions *Import the calibration file, please refer to step 3 of the operating instructions *If it still doesn't work, please contact after after-sales staff or email us Q8: Nothing displays on canvas board w...
-
Page 17: Customer Service
,please visit our official website at: www.commarker.com For Laser Engraver technical support and service please email: For Laser Engraver technical support and service please email: support@commarker.com Manufacturer: ComMarker Industrial Co., Limited ComMarker Industrial Co., Limited...
Need help?
Do you have a question about the Omni and is the answer not in the manual?
Questions and answers